Biological microorganisms and artificial micro-swimmers often locomote in heterogeneous viscous environments consisting of networks of obstacles embedded into viscous fluid media. In this work, we use the squirmer model and present a numerical investigation of the effects of shape on swimming in a heterogeneous medium. Specifically, we analyse the microorganism's propulsion speed as well as its energetic cost and swimming efficiency. The analysis allows us to probe the general characteristics of swimming in a heterogeneous viscous environment in comparison with the case of a purely viscous fluid. We found that a spheroidal microorganism always propels faster, expends less energy and is more efficient than a spherical microorganism in either a homogeneous fluid or a heterogeneous medium. Moreover, we determined that above a critical eccentricity, a spheroidal microorganism in a heterogeneous medium can swim faster than a spherical microorganism in a homogeneous fluid. Based on an analysis of the forces acting on the squirmer, we offer an explanation for the decrease in the squirmer's speed observed in heterogeneous media compared with homogeneous fluids.

Eukaryotic swimming cells such as spermatozoa, algae or protozoa use flagella or cilia to move in viscous fluids. The motion of their flexible appendages in the surrounding fluid induces propulsive forces that balance viscous drag on the cells and lead to a directed swimming motion. Here, we use our recently built database of cell motility (BOSO-Micro) to investigate the extent to which the shapes of eukaryotic swimming cells may be optimal from a hydrodynamic standpoint. We first examine the morphology of flexible flagella undergoing waving deformation and show that their amplitude-to-wavelength ratio is near that predicted theoretically to optimise the propulsive efficiency of active filaments. Next, we consider ciliates, for which locomotion is induced by the collective beating of short cilia covering their surface. We show that the aspect ratios of ciliates are close to that predicted to minimise the viscous drag of the cell body. Both results strongly suggest a key role played by hydrodynamic constraints, in particular viscous drag, in shaping eukaryotic swimming cells.

Recently, subcritical transition to turbulence in the quasi-two-dimensional (quasi-2-D) shear flow with strong linear friction (Camobreco et al., J. Fluid Mech., vol. 963, 2023, R2) has been demonstrated by the 2-D mechanism at $Re = 71\,211$, and the nonlinear Tollmien–Schlichting (TS) waves related to the edge state were approached independently of initial optimal disturbances. For 2-D plane Poiseuille flow, transition to the fully developed turbulence requires that the Reynolds number is several times larger than the critical Reynolds number $Re_c$ (Markeviciute & Kerswell, J. Fluid Mech., vol. 917, 2021, A57). In this paper, we observed the subcritical transitional flow in 2-D plane Poiseuille flow driven by the nonlinear TS waves by both linear and nonlinear optimal disturbances ($Re < Re_c$) with different quantitative edge states. The nonlinear optimal disturbances could trigger the sustained subcritical transitional flow for $Re \geqslant 2400$. The initial energy for nonlinear optimal disturbance is more efficient than the linear optimal disturbance in reaching the subcritical transitional flow for $2400 \leqslant Re \leqslant 5000$. Moreover, the initial energy of linear optimal disturbance is larger than the energy of its edge state. The nonlinear TS waves along the edge state are formed by the nonlinear optimal disturbances to trigger transitional flow, which agrees well with the main conclusions of Camobreco et al. (J. Fluid Mech., vol. 963, 2023, R2), while the required $Re$ of 2-D plane Poiseuille flow is much smaller.

We experimentally explored the effect of single-sidewall cooling on Rayleigh–Bénard (RB) convection. Canonical RB was also studied to aid insight. The scenarios shared tank dimensions and bottom and top wall temperatures; the single sidewall cooling had the top wall temperature. Turbulence was explored at two canonical Rayleigh numbers, $Ra=1.6\times 10^{10}$ and $Ra=2\times 10^9$ under Prandtl number $Pr=5.4$. Particle image velocimetry described vertical planes parallel and perpendicular to the sidewall cooling. The two $Ra$ scenarios reveal pronounced changes in the flow structure and large-scale circulation (LSC) due to the sidewall cooling. The density gradient induced by the sidewall cooling led to asymmetric descending and ascending flows and irregular LSC. Flow statistics departed from the canonical case, exhibiting lower buoyancy effects, represented by an effective Rayleigh number with effective height dependent on the distance from the lateral cooling. Velocity spectra show two scalings, $\varPhi \propto f^{-5/3}$ Kolmogorov (KO41) and $\varPhi \propto f^{-11/5}$ Bolgiano (BO59) in the larger $Ra$; the latter was not present in the smaller set-up. The BO59 scaling with sidewall cooling appears at higher frequencies than its canonical counterpart, suggesting weaker buoyancy effects. The LSC core motions allowed us to identify a characteristic time scale of the order of vortex turnover time associated with distinct vortex modes. The velocity spectra of the vortex core oscillation along its principal axis showed a scaling of $\varPhi _c \propto f^{-5/3}$ for the single sidewall cooling, which was dominant closer there. It did not occur in the canonical case, evidencing the modulation of LSC oscillation on the flow.

We studied the transport and deposition behaviour of point particles in Rayleigh–Bénard convection cells subjected to Couette-type wall shear. Direct numerical simulations (DNSs) are performed for Rayleigh number ($Ra$) in the range $10^{7} \leq Ra \leq ~10^9$ with a fixed Prandtl number $Pr = 0.71$, while the wall-shear Reynolds number ($Re_w$) is in the range $0 \leq Re_w \leq ~12\,000$. With the increase of $Re_w$, the large-scale rolls expanded horizontally, evolving into zonal flow in two-dimensional simulations or streamwise-oriented rolls in three-dimensional simulations. We observed that, for particles with a small Stokes number ($St$), they either circulated within the large-scale rolls when buoyancy dominated or drifted near the walls when shear dominated. For medium $St$ particles, pronounced spatial inhomogeneity and preferential concentration were observed regardless of the prevailing flow state. For large $St$ particles, the turbulent flow structure had a minor influence on the particles’ motion; although clustering still occurred, wall shear had a negligible influence compared with that for medium $St$ particles. We then presented the settling curves to quantify the particle deposition ratio on the walls. Our DNS results aligned well with previous theoretical predictions, which state that small $St$ particles settle with an exponential deposition ratio and large $St$ particles settle with a linear deposition ratio. For medium $St$ particles, where complex particle–turbulence interaction emerges, we developed a new model describing the settling process with an initial linear stage followed by a nonlinear stage. Unknown parameters in our model can be determined either by fitting the settling curves or using empirical relations. Compared with DNS results, our model also accurately predicts the average residence time across a wide range of $St$ for various $Re_w$.

The scaling relations mapping the turbulence statistics in compressible turbulent boundary layers (TBLs) onto their incompressible counterparts are of fundamental significance for turbulence modelling, such as the Morkovin scaling for velocity fields, while for pressure fluctuation fields, a corresponding scaling relation is currently absent. In this work, the underlying scaling relations of pressure fluctuations about Mach number ($M$) contained in their generation mechanisms are explored by analysing a series of direct numerical simulation data of compressible TBLs over a wide Mach number range $(0.5\leq M \leq 8.0)$. Based on the governing equation of pressure fluctuations, they are decomposed into components according to the properties of source terms. It is notable that the intensity of the compressible component, predominantly originating from the acoustic mode, obeys a monotonic distribution about the Mach number and wall distance; further, the intensity of the rest of the pressure components, which are mainly generated by the vorticity mode, demonstrates a uniform distribution consistent with its incompressible counterpart. Moreover, the coupling between the two components is negligibly weak. Based on the scaling relations, semiempirical models for the fluctuation intensity of both pressure and its components are constructed. Hence, a mapping relation is obtained that the profiles of pressure fluctuation intensities in compressible TBLs can be mapped onto their incompressible counterparts by removing the contribution from the acoustic mode, which can be provided by the model. The intrinsic scaling relation can provide some basic insight for pressure fluctuation modelling.

The velocity gradient tensor can be decomposed into normal straining, pure shearing and rigid rotation tensors, each with distinct symmetry and normality properties. We partition the strength of turbulent velocity gradients based on the relative contributions of these constituents in several canonical flows. These flows include forced isotropic turbulence, turbulent channels and turbulent boundary layers. For forced isotropic turbulence, the partitioning is in excellent agreement with previous results. For wall-bounded turbulence, the partitioning collapses onto the isotropic partitioning far from the wall, where the mean shearing is relatively weak. By contrast, the near-wall partitioning is dominated by shearing. Between these two regimes, the partitioning collapses well at sufficiently high friction Reynolds numbers and its variations in the buffer layer and the log-law region can be reasonably modelled as a function of the mean shearing strength. Altogether, our results highlight the expressivity and broad applicability of the velocity gradient partitioning as advantages for turbulence modelling.

A hydrodynamic theory of premixed flame propagation within closed vessels is developed assuming the flame is much thinner than all other fluid dynamic lengths. In this limit, the flame is confined to a surface separating the unburned mixture from burned combustion products, and propagates at a speed determined from the analysis of its internal structure. Unlike freely propagating flames that propagate under nearly isobaric conditions, combustion in a closed vessel results in continuous increases in pressure, burning rate and flame temperature, and a progressive decrease in flame thickness. The flame speed is shown to depend on the voluminal stretch rate, which measures the deformation of a volume element of the flame zone, and on the rate of pressure rise. Both effects are modulated by pressure-dependent Markstein numbers that depend on heat release and mixture properties while capturing the effects of temperature-dependent transport and stoichiometry. The model applies to flames of arbitrary shape propagating in general flows, laminar or turbulent, within vessels of general configurations. The main limitation of hydrodynamic flame theories is the assumption that variations inside the flame zone due to chemistry or turbulence, which could potentially alter its internal structure, are physically unresolved. Nonetheless, the theory, deduced from physical first principles, identifies the various mechanisms involved in the combustion process as demonstrated in detailed discussions of planar flames propagating in rectangular channels and spherically expanding flames in spherical vessels. It also enables the construction of instructive models to numerically simulate the evolution of multi-dimensional and corrugated flames under confinement.

This study introduces an analytical solution for the laminar entrance flow in circular pipes, aiming to confirm the occurrence of velocity overshoot. Velocity overshoot is characterised by the maximum axial velocity appearing near the pipe wall instead of the central axis. Similar to the previous studies, the analytical solution is derived from the parabolised Navier–Stokes equation; however, the specific approach used in linearising the momentum equation has not been attempted before. The accuracy of this analytical solution has been verified through a comprehensive comparison with various published experimental data. The existence of velocity overshoot at a short distance from the inlet, which is evident in numerous numerical calculations based on the full Navier–Stokes equations and corroborated by recent magnetic resonance (MR) velocimetry experiments, is identified analytically for the first time. The parabolised Navier–Stokes equation has inherent self-similarity with respect to the Reynolds number, implying that $Re$ is incorporated into the dimensionless variables rather than serving as an independent flow parameter. According to both MR velocimetry measurements and the present analytical solution, the self-similarity is not valid immediately following the pipe inlet, and this becomes more evident as $Re$ decreases; hence, the analytical solution derived from the parabolised Navier–Stokes equation cannot accurately predict the evolution of the velocity profile within this region near the pipe inlet.

The hydrodynamics of a self-propelling swimmer undergoing intermittent S-start swimming are investigated extensively with varying duty cycle $DC$, swimming period $T$, and tailbeat amplitude $A$. We find that the steady time-averaged swimming speed $\bar {U}_x$ increases directly with $A$, but varies inversely with $DC$ and $T$, where there is a maximal improvement of $541.29\,\%$ over continuous cruising swimming. Our results reveal two scaling laws, in the form of input versus output relations, that relate the swimmer's kinematics to its hydrodynamic performance: swimming speed and efficiency. A smaller $DC$ causes increased fluctuations in the swimmer's velocity generation. A larger $A$, on the other hand, allows the swimmer to reach steady swimming more quickly. Although we set out to determine scaling laws for intermittent S-start swimming, these scaling laws extend naturally to burst-and-coast and continuous modes of swimming. Additionally, we have identified, categorized and linked the wake structures produced by intermittent S-start swimmers with their velocity generation.

We investigate the concentration fluctuations of passive scalar plumes emitted from small, localised (point-like) steady sources in a neutrally stratified turbulent boundary layer over a rough wall. The study utilises high-resolution large-eddy simulations for sources of varying sizes and heights. The numerical results, which show good agreement with wind-tunnel studies, are used to estimate statistical indicators of the concentration field, including spectra and moments up to the fourth order. These allow us to elucidate the mechanisms responsible for the production, transport and dissipation of concentration fluctuations, with a focus on the very near field, where the skewness is found to have negative values – an aspect not previously highlighted. The gamma probability density function is confirmed to be a robust model for the one-point concentration at sufficiently large distances from the source. However, for ground-level releases in a well-defined area around the plume centreline, the Gaussian distribution is found to be a better statistical model. As recently demonstrated by laboratory results, for elevated releases, the peak and shape of the pre-multiplied scalar spectra are confirmed to be independent of the crosswind location for a given downwind distance. Using a stochastic model and theoretical arguments, we demonstrate that this is due to the concentration spectra being directly shaped by the transverse and vertical velocity components governing the meandering of the plume. Finally, we investigate the intermittency factor, i.e. the probability of non-zero concentration, and analyse its variability depending on the thresholds adopted for its definition.

The orientational dynamics of a spherical magnetic particle in linear shear flow subjected to an oscillating magnetic field in the flow plane is analysed in the viscous limit. The shear is in the $X$–$Y$ plane, the magnetic field is in the $X$ direction and the vorticity is perpendicular to the flow in the $Z$ direction. The relevant dimensionless groups are $\omega ^\ast$, the ratio of the frequency of the magnetic field and the strain rate, and $\varSigma$, the ratio of the magnetic and hydrodynamic torques. As $\varSigma$ is decreased, there is a transition from in-plane rotation, where the rotation is in the flow ($X$–$Y$) plane, to out-of-plane rotation, where the orientation vector is not necessarily in the $X$–$Y$ plane and the dynamics depends on the initial orientation. The particle rotation is phase-locked for in-plane rotation with discrete odd rotation number (number of rotations in one period of magnetic field oscillation), while the orbits are quasi-periodic with non-integer rotation number for out-of-plane rotation. For $\varSigma \gg 1$, regions of odd rotation number $n_o$ are bound by the lines $8 (n_o-1) \varSigma \omega ^\ast = 1$ and $8 (n_o+1) \varSigma \omega ^\ast = 1$, and there are discontinuous changes in the rotation number and mean and root-mean-square torque at these lines. For $\varSigma \ll 1$, the domains of in-plane rotation of finite width in the $\omega ^\ast$–$\varSigma$ plane extend into downward cusps at $\omega ^\ast = {1}/{2 n_o}$. The orbits are quasi-periodic between these domains, where the rotation is out of plane.

Motivated by contradicting or insufficient information regarding the large-scale flow dynamics around surface-mounted finite-height square prisms of small aspect ratio, the present study investigates the dominant vortex shedding and low-frequency dynamics around a surface-mounted cube. These flow modes were obtained from the spectral proper orthogonal decomposition of large-eddy simulation results, at a Reynolds number of $\textit {Re}=1\times 10^4$ and two different types of boundary layer: a thin and laminar boundary layer with thickness $\delta /D=0.2$ and a thick and turbulent boundary layer with $\delta /D=0.8$. The main antisymmetric mode pair revealed a new flow pattern with the alternate shedding of streamwise flow structures, indicating a transition from the half-loops of taller prisms to only streamwise strands (i.e. no vertical core) for smaller aspect ratio. The formation process of the streamwise structures is due to a reorientation of the vorticity of the arch vortex in the streamwise direction characteristic of the shed structures. The low-frequency drift mode affected the length of the recirculation region, the strength of vortex shedding, and the near-wall flow field and pressure distribution on the cube's faces, leading to low-frequency variations in the fluctuating drag and normal force coefficients. These large-scale flow dynamics were similar for both boundary layers, but minor differences were identified, related mostly to the occurrence of flow attachment and the formation of a headband vortex for the thicker boundary layer.

The featured article ‘Break-up of a falling drop containing dispersed particles’ (Nitsche and Batchelor, J. Fluid Mech., 1997, vol. 340, pp. 161–175) is G. K. Batchelor's last published paper with his former postdoctoral associate J. M. Nitsche. The objective of the study was to investigate the randomness of the velocities of interacting rigid particles falling under gravity through a viscous fluid at a small Reynolds number and its consequence for the breakup of a falling cloud of particles. The study focused on a quintessential problem of the collective dynamics of interacting particles and has been an inspiration for subsequent work.

A moving static pressure distribution is commonly used to simulate a travelling ship. However, the ship movement changes the fluid velocity around the hull, inducing pressures on the hull surface that are no longer equal to the static pressure. Therefore, we introduce a dynamic pressure correction strategy, which can accurately simulate the impact of the ship movement on the hull-surface pressure and preserve the desired hull shape under both stationary and transient conditions. The strategy is applied to a high-order spectral model and used to investigate ship-induced waves and wave resistance over a both flat and variable topography. We explore various parameters in our study, including the average water depth to ship draft ratio ($h_0/d$), the channel width to ship width ratio ($W/B$), the Froude number ($Fr_0=U/\sqrt {gh_0}$) and variations in bathymetric slope. Compared with experiments on a flat bottom, the numerical results with dynamic correction show better accuracy in the simulation of ship-induced waves and wave resistance than those obtained using a static pressure distribution. The correlation coefficient for wake waves between the numerical and experimental results is improved by approximately 0.25 with the dynamic correction strategy. The amplitude and wavelength of ship-induced mini-tsunamis over a variable topography are found to be reduced when employing a dynamic correction compared with a static pressure distribution, and this effect becomes more pronounced with higher Froude number. The static pressure approach is shown to allow large deformations of the desired hull shape and changes in ship volume which are responsible for the different wave patterns from the two approaches.

The peculiar migration and rotational dynamics of non-spherical particles in non-Newtonian flows stem from the interplay between fluid rheology and fluid inertial effects. In this paper, the cross-flow migration of a neutrally buoyant oblate spheroid (aspect ratio $AR = 0.5$) immersed in the elasto-inertial duct flow is investigated by particle-resolved simulations with the immersed boundary method. Different from spherical particles, due to the orientation-dependent lift force, the oblate spheroid migrates in an oscillating manner in the duct. The travelling period for particles reaching the duct centreline undergoes a non-monotonic change with elastic number, revealing the existence of a critical elastic number governing the migrating efficiency of oblate particles within the present flow system. For the particle rotation and orientation, the present results indicate that the particle rotation rate and orbit drifting rate are both hindered by the fluid elasticity. With increasing the fluid elasticity, three different orientation modes – log-rolling mode, kayaking-like mode and longside-flow alignment mode – are observed successively during the elasto-inertial migration of the oblate spheroid. Potentially, the present results could be used to design the rheology-based controlling strategy for guiding particles to achieve optimal focusing and orientation in microfluidic applications without the need for external forcing fields.

The effects of thermal convection on turbulence in accretion discs, and particularly its interplay with the magnetorotational instability (MRI), are of significant astrophysical interest. Despite extensive theoretical and numerical studies, such an interplay has not been explored experimentally. We conduct linear analysis of the azimuthal version of MRI (AMRI) in the presence of thermal convection and compare the results with our experimental data published before. We show that the critical Hartmann number ($Ha$) for the onset of AMRI is reduced by convection. Importantly, convection breaks symmetry between $m = \pm 1$ instability modes ($m$ is the azimuthal wavenumber). This preference for one mode over the other makes the AMRI wave appear as a ‘one-winged butterfly’.