Camber morphing is an effective way to control the lift generated by any aerofoil and potentially improve the range (as measured by the lift-to-drag ratio) and endurance (as measured by $C_l^{3/2}/C_d$ ). This can be especially useful for fixed-wing Unmanned Aerial Vehicles (UAVs) undergoing different flying manoeuvres and flight phases. This work investigates the aerodynamic characteristics of the NACA0012 aerofoil morphed using a Single Corrugated Variable-Camber (SCVC) morphing approach. Structural analysis and morphed shapes are obtained based on small-deformation beam theory using chain calculations and validated using finite-element software. The aerofoil is then reconstructed from the camber line using a Radial Basis Function (RBF)-based interpolation method (J.H.S. Fincham and M.I. Friswell, “Aerodynamic optimisation of a camber morphing aerofoil,” Aerosp. Sci. Technol., 2015). The aerodynamic analysis is done by employing two different finite-volume solvers (OpenFOAM and ANSYS-Fluent) and a panel method code (XFoil). Results reveal that the aerodynamic coefficients predicted by the two finite-volume solvers using a fully turbulent flow assumption are similar but differ from those predicted by XFoil. The aerodynamic efficiency and endurance factor of morphed aerofoils indicate that morphing is beneficial at moderate to high lift requirements. Further, the optimal morphing angle increases with an increase in the required lift. Finally, it is observed for a fixed angle-of-attack that an optimum morphing angle exists for which the aerodynamic efficiency becomes maximum.

Increasingly agile manoeuvre is an advantage in the flight of aircraft, missiles and aerial vehicles, but the principles of accelerating aerodynamics in the transonic regime are only now being fully investigated. This study contributes to the understanding of shock and separation effects on drag during axial acceleration, using a simple geometric configuration. Unsteady shock wave behavior was numerically investigated for an axisymmetric cone-cylinder using a commercial solver and the Moving Reference Frame acceleration technique. This acceleration technique was validated using unsteady numerical and experimental methods. The cone-cylinder was accelerated from Mach number 0.6 to Mach number 1.2 at 100g constant and deceleration was from Mach number 1.2 until Mach number 0.6 at –100g constant. Three cone angles were tested for the cone-cylinder with uniform cylinder diameter. Acceleration through the transonic Mach regime was characterised by a delayed and gradual shock wave development when compared to steady state, demonstrating a clear flow history effect. Deceleration through the transonic Mach regime was characterised by shock wave propagation from the base to the nose. New flow structures appeared during deceleration that do not have counterparts in the steady state, including shock interactions and propagating expansion-compression features. Gross changes in the unsteady drag coefficient curves for each cone-angle are explained with reference to unsteady shock wave behaviour for accelerating and decelerating motion.

Strategic airlift is a crucial capability for any country that wants to protect its global interests around the world. Air refueling may offer more agile and efficient airlift capabilities by increasing cargo aircraft payload and shortening airlift time. We investigated whether air refueling can shorten the total time of an airlift operation and decrease the number of cargo aircraft sorties required in a deployment scenario, especially where the distance between origin and destination is within the range of cargo aircraft. We introduced two mathematical models to compare the total airlift time and number of cargo aircraft required for given origin-destination and tanker base locations and total freight to be moved. We optimised initial cargo and fuel amount for cargo aircraft along with rendezvous point coordinates to minimise total airlift time. We used a numerical example to show that substantial airlift time and cargo aircraft sortie savings are possible through air refueling.

There are significant variations in the fuel consumption of aircraft during the descent phase of a flight. This paper uses aircraft flight data measurements to develop an improved understanding of these variations. A model of the aircraft engines is developed that is matched to flight data and shown to reproduce the time history of engine parameters. This model is used to determine the overall engine efficiency at each point during a descent. This enables an energy breakdown to be completed, in terms of mechanical energy from fuel, gravitational potential energy and kinetic energy. During descent, the aircraft engines operate at low overall pressure ratios corresponding to low fuel flow rates and low overall efficiencies. On average, the engine overall efficiency during descent is one-third of cruise efficiency. The airframe aerodynamic performance is deteriorated during descent with an average lift-to-drag ratio that is 87% of the average value at cruise. There are also large variations in air-track efficiency, and for the flights analysed the great circle descent distance was found to be 85% of the average descent air distance. To minimise fuel burn, flights should cruise as far as possible before starting descent and follow a trajectory with the shortest possible air distance. The descent air speed should be set to maximise the aircraft lift-to-drag ratio. Such descents could save up to 0.5% of the total aircraft mass in fuel.

Increasing demand for commercial air travel is projected to have additional environmental impact through increased emissions from fuel burn. This has necessitated the improvement of aircraft propulsion technologies and proposal of new concepts to mitigate this impact. The hybrid-electric aircraft propulsion system has been identified as a potential method to achieve this improvement. However, there are many challenges to overcome. One such challenges is the combination of electrical power sources and the best strategy to manage the power available in the propulsion system. Earlier methods reviewed did not quantify the mass and efficiency penalties incurred by each method, especially at system level. This work compares three power management approaches on the basis of feasibility, mass and efficiency. The focus is on voltage synchronisation and adaptation to the load rating. The three methods are the regulated rectification, the generator field flux variation and the buck-boost. This comparison was made using the propulsion system of the propulsive fuselage aircraft concept as the reference electrical configuration. Based on the findings, the generator field flux variation approach appeared to be the most promising, based on a balance of feasibility, mass and efficiency, for a 2.6MW system.

An efficient, fully coupled beam model is developed to analyse laminated composite thin-walled structures with arbitrary cross-sections. The Euler–Lagrangian equations are derived from the kinematic relationships for a One-Dimensional (1D) beam representing Three-Dimensional (3D) deformations that take into account the cross-sectional stiffness of the composite structure. The formulation of the cross-sectional stiffness includes all the deformation effects and related elastic couplings. To circumvent the problem of shear locking, exact solutions to the approximating Partial Differential Equations (PDEs) are obtained symbolically instead of by numerical integration. The developed locking-free composite beam element results in an exact stiffness matrix and has super-convergent characteristics. The beam model is tested for different types of layup, and the results are validated by comparison with experimental results from literature.

An unusual philosophical approach is proposed here to decarbonise larger civil aircraft that fly long ranges and consume a large fraction of civil aviation fuel. These inject an important amount of carbon emissions into the atmosphere, and holistic decarbonising solutions must consider this sector. A philosophical–analytical investigation is reported here on the feasibility of an airliner family to fly over long ranges and assist in the elimination of carbon dioxide emissions from civil aviation.

Backed by state-of-the-art correlations and engine performance integration analytical tools, a family of large airliners is proposed based on the development and integration of the body of a very large two-deck four-engine airliner with the engines, wings and flight control surfaces of a very long-range twin widebody jet. The proposal is for a derivative design and not a retrofit. This derivative design may enable a swifter entry to service.

The main contribution of this study is a philosophical one: a carefully evaluated aircraft family that appears to have very good potential for first-generation hydrogen-fuelled airliners using gas turbine engines for propulsion. This family offers three variants: a 380-passenger aircraft with a range of 3,300nm, a 330-passenger aircraft with a range of 4,800nm and a 230-passenger aircraft with a range of 5,500nm. The latter range is crucially important because it permits travel from anywhere in the globe to anywhere else with only one stop. The jet engine of choice is a 450kN high-bypass turbofan.

We previously described an efficient, lightweight and flexible electro-thermal system, based on directly drawn carbon nanotube web (CNT web), as part of an icing protection system for carbon fibre reinforced polymer (CFRP) composite aircraft structures. The location of the heating elements on critical lifting surface leading edges or nacelle intake lips makes them particularly susceptible to impact damage, which may leave no visible mark. This makes it desirable to have both a mechanism for identifying the location of damage to the CNT structure (and by inference, potential damage to the underlying CFRP) and a process for restoring the CNT heater to full operation. With the CNT web acting as a sensor, impact damage is identified by an increase in electrical resistance and, particularly, by infrared imaging, which reveals a cold spot or zone depending upon the CNT web layup. Whereas a unidirectional CNT web layup exhibits a large increase in resistance and loss of a full width band of operation, a cross ply quasi-isotropic CNT web arrangement suffers only a small increase in resistance and a loss of function that is highly localised to the damaged area. A novel methodology, based on dispersed CNT in resin, is described for repairing and reconnecting the CNT structure and restoring functionality. A CNT web-based electro-thermal element was applied to the leading edge of a representative carbon-fibre composite wing section to demonstrate the flexibility of this system.

The potential to recover waste heat from the exhaust gases of a turboprop engine and produce useful work through an Organic Rankine Cycle (ORC) is investigated. A thermodynamic analysis of the engine’s Brayton cycle is derived to determine the heat source available for exploitation. The aim is to use the aircraft engine fuel as the working fluid of the organic Rankine cycle in order to reduce the extra weight of the waste heat recovery system and keep the thrust-to-weight ratio as high as possible. A surrogate fuel with thermophysical properties similar to aviation gas turbine fuel is used for the ORC simulation. The evaporator design as well as the weight minimisation and safety of the suggested application are the most crucial aspects determining the feasibility of the proposed concept. The results show that there is potential in the exhaust gases to produce up to 50kW of power, corresponding to a 10.1% improvement of the overall thermal efficiency of the engine.

This paper presents an aeromechanics investigation of tiltrotor aircraft through the conversion regime of flight. The effects of the rotors-on-wing, rotors-on-empennage and wing-on-empennage interactions were investigated singularly and collectively to assess their impacts on trim behaviour, performance and conversion boundaries. The rotors-on-wing download was found to be dominant in the prediction of hover and low-speed flight performance and had a degrading effect overall. The fuselage pitch attitude and stick position were found to be significantly affected by the empennage interaction cases throughout the conversion domain. The large flap/flaperon settings used to alleviate the rotor download contributed considerably to the low-speed trim behaviour. The conversion boundaries were found to be insensitive to all the interaction cases, though the min-speed boundary was reduced marginally due to the wing-on-empennage interaction. The results showed that the combined interactions were important factors to accurately predict the trim behaviour and aircraft performance throughout the conversion corridor.

During early phases of wing design, analytic and low-fidelity methods are often used to identify promising design concepts. In many cases, solutions obtained using these methods provide intuition about the design space that is not easily obtained using higher-fidelity methods. This is especially true for aerostructural design. However, many analytic and low-fidelity aerostructural solutions are limited in application to wings with specific planforms and weight distributions. Here, a numerical method for minimising induced drag with structural constraints is presented that uses approximations that apply to unswept planar wings with arbitrary planforms and weight distributions. The method is applied to the National Aeronautics and Space Administration (NASA) Ikhana airframe to show how it can be used for rapid aerostructural optimisation and design-space exploration. The design space around the optimum solution is visualised, and the sensitivity of the optimum solution to changes in weight distribution, structural properties, wing loading and taper ratio is shown. The optimum lift distribution and wing-structure weight for the Ikhana airframe are shown to be in good agreement with analytic solutions. Whereas most modern high-fidelity solvers obtain solutions in a matter of hours, all of the solutions shown here can be obtained in a matter of seconds.

The design and development of Stratospheric Airships for High-Altitude Long-Endurance missions (HALESAs) has generated interest worldwide. Conventional airships usually have a single-lobed axisymmetrical envelope shape. In contrast, several non-axisymmetric envelope configurations have been proposed for the HALESAs, such as flattened single lobed and multi lobed. This paper describes a methodology for carrying out a comparative analysis of a conventional HALESA and the multi-lobed HALESA designed for the same design mission. A sizing methodology which enables the estimation of its design parameters to meet some user-specified requirements has been developed for airships with envelopes of both these shapes. A Multidisciplinary Design Optimisation (MDO) approach has been followed in this methodology, which includes considerations from the disciplines of aerodynamics, energy, environment and structures. The study indicates that the envelope volume, solar array area and total mass of the single-lobed conventional airship are better than those of the tri-lobed HALESA. While the multi-lobed HALESA has the advantage of a flatter upper surface resulting in higher efficiency of the solar panels, the conventional airship has lower drag, which results in superior mission performance.

New alternative jet fuels have provided many advantages in the aviation industry, especially in terms of economics and environment. However, fuel–seal compatibility is one of the major issues that restricts alternative fuel advancement into the market. Thus, to help understand and solve the problem, this study examines the swelling effect of prepared and non-prepared O-rings in different fuels and aromatic species. Stress relaxation experiments were carried out to evaluate seal compatibility under compression, which mimics engine operation conditions. Seals were compressed and immersed in a variety of fuels and their blends for about 90h while maintaining a constant temperature 30°C and constant compression force of 25% seal thickness. The two types of elastomers investigated were fluorosilicone and nitrile O-rings, which are predominantly used in the aviation industry. Meanwhile, three different fuels and aromatic species were utilised as the variables in the experiments. The fuels used were Jet-A1, SPK and SHJFCS, while the aromatic species added were propyl benzene, tetralin and p-xylene. The swelling effects were determined from the P/Po value. Results indicate that Jet-A1 has the highest swelling effect, followed by SHJFCS and SPK. It was observed that the higher the percentage of aromatics in fuel, the higher the rate of swelling. Furthermore, prepared seals had a lower swelling rate than did non-prepared seals. Meanwhile, the intensity of the swelling effect in the Jet-A1-SHJFCS blends was in the order of 60/40, 85/15 and 50/50 blend. The work done in this study will aid in the selection of suitable aromatic species in future fuels. The novelty of this research lies in the determination of the appropriate amount of aromatic content as well as the selection of type of aromatic and its mixture fuel. Moreover, the various proportions of fuel blends with aromatic are investigated. The primary aim of this study is to understand the behaviour of prepared and non-prepared seals, and their compatibility with alternative fuels.

The addition of wedge-like fairings onto the side of missiles and space launch vehicles, to shield devices such as cameras and reaction jet nozzles, creates additional drag, particularly when in supersonic and hypersonic freestream flow. An experimental and computational study was performed to obtain aerodynamic data on simple representative configurations to test the accuracy of simple theories for the drag increment due to these types of fairings. A semi-empirical method to estimate drag on wedge-shaped projections is presented, which may be used by missile designers to provide predictions of the drag increment due to wedge-like fairings. The method is shown to be valid where the wedge width is much smaller than body diameter, and across the Mach number range 4–8.2 but is likely to be valid for higher Mach numbers. Drag coefficient is found to increase with increasing wedge angle and reducing wedge slenderness, although increasing slenderness tends to increase skin friction drag.

The importance of fuel injection methods and their atomisation characteristics has been well described in literature. Also, there are a large number of studies in literature detailing the impact of bulk properties of conventional fuels on atomisation and spray characteristics. However, there is a lack of knowledge on how different alternative fuels, and specifically aromatic species, impact spray and atomisation characteristics. In this investigation, the impact of alternative fuels, selected aromatic species and their properties on spray atomisation was studied. Details of how different aromatic structures, bonds and other micro properties of aromatics species impact spray and atomisation characteristics were investigated. To achieve this objective, testing was conducted using a Rolls-Royce Tay engine fuel injector. It was found that the droplet sizes in the form of the Sauter Mean Diameter (SMD) correlate well with fuel properties including density, viscosity and surface tension, which is in line with other published literature. Moreover, it was found that there are several aromatic species (ethylbenzene, cumene and tert-butylbenzene) which display improved atomisation. This indicates that the size of the aliphatic groups attached to the benzene ring in the aromatic molecule impact on the drop size and thereby the combustion characteristics. The worst performers were polyaromatic naphthalene compounds. With the increasing push for fuels with selected aromatic species in the future, this study provides knowledge on the impact of their on the atomisation characteristics.

This paper presents a performance analysis on a novel engine concept, currently under development, in order to achieve hybrid air-breathing rocket technology. A component-level approach has been developed to simulate the performance of the engine at Mach 5, and the thermodynamic interaction of the different working fluids has been analysed. The bypass ramjet duct has also been included in the model. This facilitates the improved evaluation of performance parameters. The impact of ram drag induced by the intake of the engine has also been demonstrated. The whole model is introduced into a multi-platform application for aeroengine simulation to make it accessible to the interested reader. Results show that the bypass duct modelling increases the overall efficiency by approximately 7%. The model calculates the specific impulse at approximately 1800 seconds, which is 4 times higher than any chemical rocket.

Real-time flight data from the Automatic Dependent Surveillance–Broadcast (ADS-B) has been integrated, through a data interface, with a flight performance computer program to predict aviation emissions at altitude. The ADS-B, along with data from Mode-S, are then used to ‘fly’ selected long-range aircraft models (Airbus A380-841, A330-343 and A350-900) and one turboprop (ATR72). Over 2,500 flight trajectories have been processed to demonstrate the integration between databases and software systems. Emissions are calculated for altitudes greater than 3,000 feet (609m) and exclude landing and take-off cycles. This proof of concept fills a gap in the aviation emissions inventories, since it uses real-time flights and produces estimates at a very granular level. It can be used to analyse emissions of gases such as carbon dioxide ($\mathrm{CO}_2$), carbon monoxide (CO), nitrogen oxides ($\mathrm{NO}_x$) and water vapour on a specific route (city pair), for a specific aircraft, for an entire fleet, or on a seasonal basis. It is shown how $\mathrm{NO}_x$ and water vapour emissions concentrate around tropospheric altitudes only for long-range flights, and that the cruise range is the biggest discriminator in the absolute value of these and other exhaust emissions.

Air traffic controller training is highly regulated but lacks prescribed common assessment criteria and methods to evaluate trainees at the level of basic training and consideration of how trainees in fluence flight efficiency. We investigated whether there is a correlation between two parameters, viz. the trainees’ assessment score and fuel consumption, obtained and calculated after real-time human-in-the-loop radar simulations within the ATCOSIMA project. Although basic training assessment standards emphasise safety indicators, it was expected that trainees with higher assessment scores would achieve better flight efficiency, i.e. less fuel consumption. However, the results showed that trainees’ assessment scores and fuel consumption did not correlate in the expected way, leading to several conclusions.

Turbulence and gusts cause variations in the aerodynamic forces and moments applied to the structure of aircraft, resulting in passenger discomfort and dynamic loads on the structure that it must be designed to support. By designing Gust Load Alleviation (GLA) systems, two objectives can be achieved: first, realizing higher passenger comfort; and second, reducing the dynamic structural loads, which allows the design of lighter structures. In this paper, a methodology for designing combined feedback/feedforward GLA systems is proposed. The methodology relies on the availability of a wind profile ahead of the aircraft measured by a Doppler LIDAR sensor, and is based on $H_{\infty}$-optimal control techniques and a discrete-time preview-control problem formulation. Moreover, to allow design trade-offs between those two objectives (to achieve design flexibility) as well as to allow specification of robustness criteria, a variant of the problem using multi-channel $H_{\infty}$-optimal control techniques is introduced. The methodology developed in this paper is intended to be applied to large aircraft, e.g. transport aircraft or business jets. The simulation results show the effectiveness of the proposed design methodology in accounting for the measured wind profile to achieve the two mentioned objectives, while ensuring both design flexibility and controller robustness and optimality.

The aeroelastic phenomenon of limit-cycle oscillations (LCOs) is analysed using a projection-based reduced-order model (PROM) and Navier–Stokes computational fluid dynamics (CFD) in the time domain. The proposed approach employs incompressible Navier–Stokes CFD to construct the full-order model flow field. A proper orthogonal decomposition (POD) of the snapshot matrix is conducted to extract the POD modes and corresponding temporal coefficients. The POD modes are directly projected to the incompressible Navier–Stokes equation to reconstruct the flow field efficiently. The methodology is applied to a plunging cylinder and an aerofoil undergoing LCOs. This scheme decreases the computational time while preserving the capability to predict the flow field accurately. The ROM is capable of reducing the computational time by at least 70% while maintaining the discrepancy within 0.1%. The causes of LCOs are also investigated. The scheme can be used to analyse non-linear aeroelastic phenomena in the time domain with reduced computational time.