In this paper, a single-layer band-stop frequency selective surface (FSS) by combination of Mike Kastle unit and square ring unit is proposed to achieve wide angular stable shielding. Owing to the rotational symmetry of the structure, the designed FSS is insensitive to polarization. By the combination design, the wide angular stability can be achieved as the incident angle increases from 0° to 85°, with only a maximum frequency deviation of 0.012 GHz. Meanwhile, the mechanism of the proposed FSS is investigated by the parametric analysis of equivalent circuit model. The prototype was manufactured and measured to verify the design and simulation analysis, and the measurement results were in good agreement with the simulation results.

This article introduces an innovative approach to antenna array design, focusing on synthesizing the optimal radiation pattern for fifth-generation (5G) communication. The authors have designed a reliable linear and elliptical antenna array (EEA) of dipole elements by employing sailfish optimization (SFO). 5G technology promises transformative improvements in wireless communication with high data rates, expanded capacity, minimal latency, and exceptional service quality. The crux of 5G lies in the precision of antenna array design, aiming for an emission pattern with minimal side lobe levels (SLLs) and a narrow half-power beam width (HPBW). A narrower HPBW is essential for efficient long-range communication, whereas reducing the SLLs enhances signal clarity. The SFO optimizes the current excitation of each antenna element for reducing the mutual coupling effects and lowering the SLL and HPBW values in linear and EEAs. This paper uses the exact excitation to each element to show the linear antenna arrays (LAA) (10-, 16-element) design examples and EAA (8-, 12-, 20-element) structures. The LAA and EAA design examples obtained with the SFO algorithm establish the advancement in SLL suppression over the uniform antenna array and the methods proclaimed in the recent article.

This paper proposes a lightweight frequency selective surface polarization-insensitive wideband metamaterial absorber in C band and X band that employs only a few resistive elements. The proposed absorber is embodied with four quadrature slotted inner circular patch, which is horizontally and vertically bisected, and outer concentric copper rings of 0.035 mm thickness are attached with four lumped resistors placed at 90° apart. A slotted inner circular patch provides significant inductive and capacitive loading. The absorption bandwidth of 8.02 GHz with more than 90% absorption is observed from 5.69 to 13.71 GHz under normal incidence and maintains almost same absorptivity range under oblique incidence up to 45° in both transverse electric mode and transverse magnetic mode. The designed metamaterial absorber is fabricated and measured using free space measurement technique. The actual experiments and the simulated ones are in good agreement.

This paper details the design and development of a planar switched beam network using 4 × 4 Butler matrix (BM) over a thin and flexible type biocompatible substrate. Four mils thick liquid crystal polymer (LCP) is used as a substrate here (ϵr = 2.92, tanδ = 0.002). The proposed design is centered at 28 GHz, targeting commercial millimeter-wave applications. Floral-shaped antenna with defective ground structures has been implemented as basic radiating elements. The whole structure is based on microstrip line configuration. The architecture occupies an area of 23.85 × 19.20 mm2 over the LCP substrate. Individual components of the BM are detailed here, followed by a system analysis of the whole integrated structure. The present work also covers the electrical equivalent circuit modeling of the whole beam-forming network. The fabricated prototype offers better than 18 dB return losses at each input port for the desired frequency band with 6 dBi (max.) peak gain and 500 MHz bandwidth around the center frequency. Port-to-port isolation of better than 15 dB is achieved with this topology. Experimental and simulated results are in good agreement in all aspects. A comparative study is also chalked out to highlight the significance of the current research work with respect to alike earlier reported structures.

This paper presents a methodology to design band-pass filters having ultrawide stopband characteristics using multilayer circular substrate-integrated waveguide (SIW) cavities. The orthogonal microstrip feedlines are used as input and output ports that are present at the top and bottom layers, while the middle layers are used to couple the SIW cavities. Higher-order spurious modes of the circular SIW cavity are suppressed by using orthogonal feeding mechanism and properly adjusting the arc-shaped slots between the cavities. To validate the present approach, two filters (second- and fourth-order) have been designed and fabricated and their characteristics are measured. The second-order filter exhibits a stopband rejection below 25 dB up to nearly 5.07f0, while the fourth-order filter has a stopband characteristic of nearly 5.05f0 with 20 dB rejection. The filters allow only TM010 mode propagation and attenuate the higher-order spurious modes of the cavity.

3D printed orthomode transducer (OMT) integrated with a 3D printed lens antenna is presented in this work. The OMT integrated with the lens antenna covers the range of 54–80 GHz, the radiator can handle a fractional bandwidth of 38%. Fused filament fabrication printing process is used for the domed elliptical profile lens antenna and polyjet printing process is used for fabrication of the OMT. The simulated radiation efficiency of the antenna remains above 90% for the entire bandwidth and the structure shows a gain of above 16 dBi.

This paper presents a design methodology for a broadband high-efficiency power amplifier (PA). The large available impedance space of the extended continuous Class-GF mode is employed. A novel output matching network of the PA consisting of a rectangular double transmission line structure is proposed to meet impedance requirements. To validate the effectiveness of this structure, a high-efficiency PA operating in 0.8–3.0 GHz is designed using a CGH40010F GaN transistor. The measured results demonstrate that the drain efficiency falls within the range of 63.2%–71.9%, the output power varies from 40.2 to 42.2 dBm, and the gain ranges from 9.4 to 11.3 dB within the frequency band of 0.8–3 GHz. The realized PA exhibits an extremely competitive relative bandwidth of 115.8%.

An enhanced wideband tracking method for characteristic modes (CMs) is investigated in this paper. The method consists of three stages, and its core tracking stage (CTS) is based on a classical eigenvector correlation-based algorithm. To decrease the tracking time and eliminate the crossing avoidance (CRA), we append a commonly used eigenvalue filter (EF) as the preprocessing stage and a novel postprocessing stage to the CTS. The proposed postprocessing stage can identify all CRA mode pairs by analyzing their trajectory and correlation characteristics. Subsequently, it can predict corresponding CRA frequencies and correct problematic qualities rapidly. Considering potential variations in eigenvector numbers at consecutive frequency samples caused by the EF, a new execution condition for the adaptive frequency adjustment in the CTS is introduced. Finally, CMs of a conductor plate and a fractal structure are investigated to demonstrate the performance of the proposed method, and the obtained results are discussed.

This paper introduces an innovative conceptual design of a 400 kW solid-state power amplifier (SSPA) station and presents preliminary measurements for the key components. Recent advancements and benefits of solid-state technology have made the prospect of replacing vacuum tubes increasingly appealing. Historically, a significant challenge was the limited output power capacity of individual solid-state transistors, necessitating the integration of numerous units to generate high-power microwave signals in the range of hundreds of kilowatts. However, modern transistors capable of producing over 2 kW of output power have emerged, facilitating this transition. Another weak point was low power efficiency in high-power operating mode. The advanced rugged technology (ART) of solid-state devices enables the utilization of these transistors in nonlinear and switching operating classes, thereby enabling the creation of high-efficiency high-power amplifiers. In this conceptual design, 264 SSPA modules based on ART, each with a power output of 1.6 kW, are combined. The measurements revealed a single SSPA capable of delivering up to 2 kW output power with a power efficiency of 73% at frequency of 352 MHz. Due to the minimal losses during module combination and working SSPA in Class-C operation mode, the power efficiency of the station is expected to closely mirror that of a single module.

This study introduces a novel approach to radar-based hand gesture recognition (HGR), addressing the challenges of energy efficiency and reliability by employing real-time gesture recognition at the frame level. Our solution bypasses the computationally expensive preprocessing steps, such as 2D fast Fourier transforms (FFTs), traditionally employed for range-Doppler information generation. Instead, we capitalize on time-domain radar data and harness the energy-efficient capabilities of spiking neural networks (SNNs) models, recognized for their sparsity and spikes-based communication, thus optimizing the overall energy efficiency of our proposed solution. Experimental results affirm the effectiveness of our approach, showcasing significant classification accuracy on the test dataset, with peak performance achieving a mean accuracy of 99.75%. To further validate the reliability of our solution, individuals who have not participated in the dataset collection conduct real-time live testing, demonstrating the consistency of our theoretical findings. Real-time inference reveals a substantial degree of spikes sparsity, ranging from 75% to 97%, depending on the presence or absence of a performed gesture. By eliminating the computational burden of preprocessing steps and leveraging the power of (SNNs), our solution presents a promising alternative that enhances the performance and usability of radar-based (HGR) systems.

An orthogonally oriented microstrip-fed bi-element ultra-wideband (UWB) diversity antenna possessing a super-wide bandwidth, high isolation, and band rejection attributes is proposed. The intended diversity antenna uses a 2nd-order Cayley fractal tree-shaped neutralization line among a pair of radiating square monopoles along with additional components like extended ground stubs, hybrid Koch fractal parasitic elements, and an L-shaped defected ground structure to attain high isolation of <−20 dB over 3.1–18 GHz. To nullify the intervention from the existent wireless local area network band, a hybrid Koch–Minkowski slot is carved out from the radiators. A minimal inter-element spacing of 8 mm is attained with the suggested layout measuring 28 mm (L) × 42 mm (W) in extent. The numerical as well as experimental investigations of vital diversity attributes like the envelope correlation coefficient, mean effective gain, total active reflection coefficient, and multiplexing efficiency depict high diversity actualization. The consistency amidst the simulation as well as the empirical results recommends the worthiness of the intended antenna for handy UWB and UWB multiple-input multiple-output systems.

A single-layer polarization converting metasurface (PCMS) with wideband is presented for polarization conversion and radar cross-section (RCS) reduction. The proposed PCMS is composed of metallic biconic shape resonator imprinted on a metal-backed F4BM dielectric substrate of relative permittivity 2.2 and loss tangent 0.001. The unit cell has a compact size of 0.16$\lambda_\mathrm{o} \times 0.16\lambda_\mathrm{o}$. A comprehensive parametric analysis, angular sensitivity study, bistatic and monostatic RCS analysis are conducted by illuminating the proposed PCMS using linearly polarized (LP) plane waves. The PCMS converts LP electromagnetic waves to their orthogonal polarization state in the frequency band of 8.7–24.8 GHz resulting in polarization conversion ratio over 90% with a fractional bandwidth of 96%. Additionally, the developed structure is applied in chessboard configuration, using phase cancellation techniques for RCS reduction, that achieve 10 dB RCS reduction across a wideband of 7.9–23.4 GHz. The unit cell and its rotated version has a cross-polarization reflection phase difference of (${180}\pm {37}{^\circ}$) in the operating band, which fulfill the criteria for RCS reduction. The chessboard configuration exhibits a scattering pattern with four strong lobes that deviates from the normal incident path because of the phase cancellation in normal direction. The experimental results are in good agreement with the simulated result. Applications for the developed structure include antenna design (gain enhancement and beam steering), target hiding, imaging, and microwave communications.

A novel metasurface offering polarization conversion characteristic in five bands is studied and developed in this paper. To provide the anisotropic feature to the structure, a diagonally placed tapered rod is combined with two semicircular stubs. Due to the controlling ability to convert horizontal to vertical polarization and vice versa, and linear to circular polarization (CP), it serves as a multifunctional polarization converter. Simulation results suggest that the proposed polarizer functions as cross polarizer over 4.74−5.12 and 9.12−13.48 GHz. Additionally, it exhibits a distinct type of rotational sense across 4.24−4.68, 5.24−8.64, and 13.72–15.14 GHz in its linear to CP conversion behavior. The axial ratio of the polarizer is well below 3 dB throughout overall CP bands due to the minimum tolerance level in reflection phases with respect to acceptable limits. Moreover, it is noticed that the sense of CP is left-handed in the first band while right-handed in the remaining two bands. Thus, the suggested polarizer has potential to be integrated with antennas for satellite, defense, industry applications for getting the desired type of polarization in the distinguished bands.

A novel wideband reflectarray antenna (RA) is designed for 5G millimeter (mm) wave communications in the frequency range of 26.5–36 GHz. The proposed unit cell is constructed using a grid periodicity of 0.52${{\lambda }_0}{ }$ that offers 636° phase change through phase delay lines (PDLs) (${{\theta }_{\text{s}}}$). These PDLs are attached to the outer end of the unit cell comprising semi-circular rings. Bandwidth enhancement is achieved by incorporating a corrugated slot technique and a suitable air gap beneath the substrate. The proposed center-fed reflectarray is composed of 513 elements distributed in a circular aperture (13.46${{\lambda }_0}$). Using mirror-symmetrical distribution of the unit cells, a cross-polarization reduction as low as −50 dB is realized. At 30 GHz, RA has a measured peak gain of 28.2 dBi, a sidelobe level of −14.3 dB, and an aperture efficiency of 31.4%. The prototype antenna is fabricated, and the simulation results are experimentally validated. The measured 1-dB and 3-dB gain bandwidths of the proposed reflectarray antenna are 31.3% and 41.6%, respectively. The proposed broadband reflectarray can be a potential choice for inter-satellite services like inter-satellite networking/satellite positioning and control; fixed satellite services such as GPS satellite synchronization and data direct to home TV; and satellite position fixing.

In this paper, we investigate low-cost solutions for enabling ground moving target indication applications with multichannel mobile passive radar systems. As known, in order to be competitive with their active counterparts, passive radars are typically characterized by severe constraints in terms of cost, complexity, and compactness, especially when installed on moving platforms. On the one hand, carrying out the computations onboard requires processing techniques as simple as possible. On the other hand, the need for lightweight and compact systems that can be installed on a moving platform requires using a limited number of receiving channels. To meet these requirements, we propose a series of nonadaptive detectors based on multichannel displaced phase center antennas, which allow suppressing the Doppler-spread clutter component without requiring computationally intensive space–time adaptive processing techniques. Moreover, we explore the use of nonuniformly spaced array configurations on receive, which represent a good alternative to conventional uniform linear arrays when a limited number of receiving channels can be implemented. The effectiveness of the proposed processing techniques and antenna design solutions is demonstrated via numerical analysis for the case of a DVB-T-based mobile passive radar system.

Path loss prediction (PLP) is an important feature of wireless communications because it allows a receiver to anticipate the signal strength that will be received from a transmitter at a given distance. The PLP is done by using machine learning models that take into account numerous aspects such as the frequency of the signal, the surroundings, and the type of antenna. Various machine learning methods are used to anticipate path loss propagation but it is difficult to predict path loss in unknown propagation conditions. In existing models rely on incomplete or outdated data, which can affect the accuracy and reliability of predictions and they do not take into account the effects of environmental factors, such as terrain, foliage, and weather conditions, on path loss. Furthermore, existing models are not robust enough to handle the real-world variability and uncertainty, leading to significant errors in predictions. To tackle this issue, a novel ultrahigh frequency (UHF) PLP based on K-nearest neighbors (KNNs) is developed for predicting and optimizing the path loss for UHF. In this proposed model, a KNN-based PLP has been used to predict the path loss in the UHF. This technique is used for high-accuracy PLP through KNN forecast route loss by determining the K-nearest data points to a particular test point based on a distance metric. Moreover, the existing models were not able to optimize path loss due to complex and large-scale machine learning models. Therefore, the stochastic gradient descent technique has been used to minimize the objective function, which is often a measure of the difference between the model’s predictions and the actual output that will fine-tune the parameters of the KNN model, by measuring the similarity between data points. This model is implemented using Python to make it a lot more convenient.

A novel wideband nonuniform metasurface antenna with stable gain is demonstrated. The nonuniform metasurface is composed of square patches and rings and is excited by a slot antenna. Based on characteristic mode analysis, two characteristic modes with same current direction are selected to achieve stable radiation performance in a wide frequency range. The wideband operation is achieved by assembling the resonant modes of the metasurface and slot antenna. The measured results show that the −10 dB impedance bandwidth of the proposed antenna is from 4.3 to 8.4 GHz (64.57%), and the 2 dB gain bandwidth is from 4.3 to 6.2 GHz (36.2%) with a peak gain value of 9.42 dBi. Moreover, broadside radiation performance is achieved.

An isolated low-profile multilayer all-ports-matched broadside-coupled balun (BCB) with arbitrary isolation bandwidth is presented. Analytical relations are derived and provided for the isolation circuit (IC) design in terms of electrical and physical parameters. Accordingly, instructions are given on obtaining optimum bandwidth and isolation responses for the IC. Design procedure for the BCB is presented together with a case study for power amplifier application. The BCB is validated theoretically, analytically, and experimentally, and results are in good agreement. The fabricated balun has insertion loss of 0.27 dB, input and output return losses of 19 dB, isolation of 20 dB at fc, and phase and magnitude imbalance better than 2° and 0.2 dB across the Bandwidth (BW), respectively. The realized isolated balun has dimensions of 0.06λg × 0.03λg.

In this paper, pulse splitting approach is proposed to simultaneously reduce the sidelobe level (SLL) of fundamental signal and maximum sideband levels (SBLs) of harmonic signals for time-modulated linear array (TMLA). This is achieved by controlling only the periodic switching time sequence of each element of the TMLA. In pulse splitting, the on–off switching sequence of each radiating element is characterized by multiple rectangular sub-pulses within the modulation period which increase the degrees of freedom in order to better synthesize the desired fundamental pattern with simultaneous suppression of harmonic or sideband radiation. A genetic algorithm is employed to optimize the switch-on and switch-off instants of each sub-pulse for each element for 16-element uniform amplitude, phase, and space linear antenna array. The simulation results reveal that the proposed method can achieve the desired patterns with very low SLL and SBLs compared with previous published results.

A simple and compact three-way planar power divider, which avoids the floating common node of the isolation resistors, is presented. The proposed structure exhibits a wideband operation (measured frequency range of 1.6–3.3 GHz and bandwidth of 69.4%) with good return loss and isolation characteristics. Transmission line theory is used for the mathematical analysis and extraction of design equations, followed by simulations and experimental measurements that confirm the predicted results. The proposed divider achieves an equal power split (∼32%, −4.9 ± 0.4 dB insertion loss) between the input and each output port. The measured return loss is better than −10 dB at all ports, and the measured maximum isolation is close to −30 dB. The proposed design exhibits a fully planar structure, thus eliminating the need for a floating common node for the isolation resistors. Additionally, its structure is much simpler (i.e., no coupled lines, crossovers, or lumped capacitors are required) than other designs, achieves wideband operation, and provides design simplicity, flexibility, and easy implementation. Despite its simple noncomplicated structure, the proposed three-way planar divider achieves similar (or in some cases, better) performance and size than other more complicated structures. Furthermore, it can be expanded to an n-way structure.