This article presented a compact bandpass filter with wide-stopband performance. Two substrate integrated waveguide (SIW) cavities and a short-circuited coplanar line introduced between the two cavities are used to realize a compact third-order bandpass filter. The passband is generated by combining the resonant frequency of TE101 mode of the SIW cavities and the fundamental resonant frequency of the short-circuited coplanar line. The size of the proposed filter reduces significantly in comparison with conventional third-order SIW filters. Moreover, the center frequency (CF) and the bandwidth of the filter can be controlled by adjusting the structural parameters of the filter. In addition, the first higher-order mode TE102 of the SIW cavity is suppressed by minimizing the coupling of TE102 mode in order to obtain wide-stopband performance. The proposed filter is designed, fabricated, and measured, and the simulation and measurement results show a good agreement. The filter exhibits compact size, low loss, and a rejection higher than 20 dB up to 1.94f0.

In this paper, a novel directional filter (DF) is proposed and implemented using substrate integrated waveguide (SIW) technology which exhibits the advantages of compact size and simple structure. The proposed DF is realized by two half mode substrate integrated waveguides (HMSIWs) and two substrate integrated circular cavity (SICC) resonators operating in the TM110 degenerate modes in which an aperture is utilized to realize the coupling between HMSIWs and SICCs. Two slotlines with appropriate dimensions, etched on the top and bottom planes, are utilized in order to control coupling strength between two cascaded SICC resonators. The proposed two-circular cavity SIW DF at 12.3 GHz is designed and fabricated with a normal printed circuit board process. Measured and simulated results indicate that the DF has a 3.25% bandwidth, and the return loss as well as isolation are better than 10.5 and 15 dB, respectively.

This paper discusses the design of chip-less RFID tags of a standard pocket size of 69 mm by 156 mm. These tags are based on lumped elements of copper metal traces constructed on a thin polyamide flexible substrate. Moreover, a low-cost single-chip Bluetooth detector circuit system is demonstrated. Two different detection methods: variable coil load coupling and optical light intensity detection were combined to yield 256 unique ID codes. In the first method, by utilizing simple 4 MHz digital drivers and an integrated analog to digital converter (ADC) in the reader controller; various inductively coupled resonant loads corresponding to multiple distinct tags could be differentiated, yielding eight different (3-bit) ID codes. The additional via-based hole pattern reflectometer method creates additional 32 distinct levels (5-bit) utilizing 650 nm visible light-emitting diode and a simple trans-impedance operational along with the same analog ADC pins of a Bluetooth controller. The printed circuit board trace coil on the two-layer low-cost FR-4 waterproof sealed detector unit is simultaneously used as a Qi wireless power receiver to charge the120 mAh 2450 Lithium Polymer (LiR) battery. The device could remain operational for more than a month with a single charge; remaining connected with a mobile device and enabling 10 readouts daily.

We present details of on-wafer-level 16-term error model calibration kits used for the characterization of W-band circuits based on a grounded coplanar waveguide (GCPW). These circuits were fabricated on a thin gallium arsenide (GaAs) substrate, and via holes, were utilized to ensure single mode propagation (i.e., eliminating the parallel-plate mode or surface mode). To ensure the accuracy of the definition for the calibration kits, multi-line thru-reflect-line (MTRL) assistant standards were also fabricated on the same wafer and measured. The same wafer also contained passive and active devices, which were measured subject to both 16-term and conventional line-reflect-reflect-match calibrations. Measurement results show that 16-term calibration kits are capable of determining the cross-talk more accurately. Other typical calibration techniques were also implemented using the standards on the GCPW calibration kits, and were compared with the MTRL calibration using a passive device under test. This revealed that the proposed GCPW GaAs calibration substrate could be a feasible alternative to conventional CPW impedance standard substrates, for on-wafer measurements at W-band and above.

The dynamic characteristic of rain fade slope is one important factor in determining the availability of a communication system, and it is very useful in the design of fade countermeasures. In the literature, many models were proposed for rain fade slope for earth-to-satellite links. However, there are no models available for rain fade point to point terrestrial microwave links. This paper proposes a new model for the estimation of rain fade slope statistics for terrestrial microwave links in tropical regions. First, the ITU-R model for rain fade slope for earth-to-satellite link was compared with the corresponding statistics obtained from rain attenuation data measured from three terrestrial links in Malaysia. It is found that the expression of its distribution and its standard deviation should be modified. This leads to the derivation of the proposed rain fade slope model based on the statistics of one link. Then, it is tested using the remaining data and its results were very close to the measured statistics for all attenuation levels higher than 1 dB. Moreover, the model was validated using the chi-square goodness-of-fit test.

We consider the scattering and absorption of the H-polarized plane wave by finite and semi-infinite systems of layers in the THz range. Every layer consists of an infinite graphene strip grating embedded into a dielectric slab. The solution of the problem we obtain in several steps. First, with the use of the method of singular integral equations we obtain scattering matrices of a single layer. Then, we present equations for the finite and semi-infinite systems of layers relatively the Fourier amplitudes of the scattered field. The frequency dependences of the reflection, transmission, and absorption coefficients demonstrate the variety of resonances: plasmon, slab-mode, grating-mode resonances, and resonances of the multilayer structure.

In this paper, two asymmetric co-planar waveguide (ACPW) fed circularly polarized (CP) zeroth-order resonance (ZOR) antennas (Antenna I and II) are presented using a composite right and left-handed transmission line (CRLH-TL) approach. By adding a stub on the left side of the ACPW ground and adjusting its length, circularly polarization property has been achieved in Antenna I. The simulated 3 dB axial ratio bandwidth (ARBW) of Antenna I is 1750 MHz (3.50–5.25 GHz). Next, the left side ground plane of Antenna I is further defected by etching a quarter wavelength slit to introduce a notch band (Antenna II). Antenna II has an extended 10 dB return loss bandwidth of 2200 MHz (3.28–5.48 GHz) with a band notch from 4.18–4.65 GHz that isolates the WiMAX and 5.2 GHz WLAN bands. ARBWs of 1080 and 870 MHz are achieved in the first and second band of Antenna II. The overlapping 3 dB ARBW and 10 dB return loss bandwidths of Antenna II in these two bands are 770 and 830 MHz, respectively.

This paper presents a two-elements based, dual polarized, single layer, patch antenna array with improved isolation between transmit (Tx) and receive (Rx) ports for 2.4 GHz in-band full duplex (IBFD) or simultaneous transmit and receive wireless applications. The differential feeding deployed at the Rx port effectively suppresses the coupling which is termed as self-interference from the Tx port to achieve high Tx–Rx interport isolation. A simple 3 dB/180° ring hybrid coupler with nice amplitude and phase balance characteristics has been used for differential Rx operation. The mathematical description for a differential feeding based self-interference cancellation mechanism is also presented for the proposed dual polarized IBFD antenna array. The measurement results for the implemented prototype of the antenna array demonstrate very nice levels of Tx–Rx interport isolation. The implemented single layer, compact antenna array presents 10 dB return-loss bandwidth of more than 50 MHz for both Tx and Rx ports. The prototype achieves >80 dB peak interport isolation and 75 dB (65 dB) isolation in 20 MHz (50 MHz) bandwidth.

A novel dual-polarization, single-layer reflectarray has been designed and manufactured to operate at receive (20 GHz) and transmit (30 GHz) frequencies for Ka-band terminal antennas. The reflectarray unit cell is composed of several types of resonant elements printed on the upper side of a conductor-backed substrate, which are designed to produce a collimated beam at 20 and 30 GHz in dual polarization. Cross-shaped loops are used to provide the required phases at 20 GHz, while crossed dipoles and modified truncated rings are used to control the phasing at 30 GHz. The resonant lengths of the proposed elements have been adjusted cell by cell by means of a two-dimensional interpolation method to achieve the required phase shift at each frequency. Two different feeds have been used to illuminate the reflectarray at 20 and 30 GHz. The measured gain is 28.02 dBi at 20 GHz and 32.14 dBi at 30 GHz. The measurement results show that the radiation patterns of the designed single-layer reflectarray antenna are in good agreement with those achieved from the simulations.

A novel 1 × 4 phased array elliptical inverted T-shaped slotted sectored patch antenna with defected ground structure (DGS), resonate at proposed ultra-wide tetra band at 28, 43, 51, and 64 GHz with high gain and beam-steering capabilities is presented. An inverted T-shaped slotted stub is used with the sectored patch to achieve ultra-wideband properties. In order to resonate the antenna at four different bands, DGS of round bracket slot is etched on the ground. The 1 × 4 phased arrays are used at the top edge and bottom edge of mobile PCB with high gain. The simulation results show that the antenna has four ultra-wide bands: 25.8–29.7, 40.6–44.6, 49.2–53.1, and 62.2–74 GHz with a maximum gain of 16.5 dBi at 51 GHz. The phased array antenna is capable to steer its main beam within ±30° at the 26, 28, and 43 GHz, using appropriate phase shifts of each antenna element. The proposed millimeter wave antenna is particularly suitable for cellular infrastructures and can be a candidate for emerging 5G mobile applications. The availability of an additional 11.8 GHz (62.2–74 GHz) of contiguous unlicensed spectrum will allow the launching of new exciting wireless services.

In this paper, a wideband circularly polarized corrugated G-shaped grounded ring slot antenna is presented. The proposed antenna structure is excited using a coplanar waveguide-fed monopole antenna, which is placed inside a corrugated G-shaped grounded ring. Due to the asymmetry in the ground plane, two orthogonal modes, having equal magnitude and out of phase by 90° are excited, resulting in circular polarization (CP). The generation of the CP in the proposed antenna structure is explained using thin dipole current element approximation. A prototype of the proposed antenna is fabricated and tested. The measured results exhibit a 3 dB axial ratio bandwidth of 37.6% (2.22–3.25 GHz), and reflection coefficient bandwidth (|S11| ≤ −10 dB) of 47.91% (2.13–3.47 GHz). Additionally, the design guidelines are also presented for G-shaped grounded ring slot antennas.