This study evaluated the cleaning efficacy of a root canal system by Nd:YAG laser and rotary instruments. Sixty single-rooted human teeth were divided into four experimental groups (n=15). In the first group the teeth were prepared with a step-back technique using conventional K-files. In the second and third groups, tooth preparation was carried out using Nd:YAG laser and rotary NiTi instruments, respectively. Teeth in the fourth group were prepared by combined laser and rotary methods. The smear layer remaining on canal walls was then assessed by scanning electron microscopy in the coronal, middle, and apical portions. The comparison of smear layer removal efficacy between groups was carried out by Kruskal–Wallis and Mann–Whitney U tests. The mean grades of smear layer removal in rotary-laser, rotary, laser and step-back techniques were 1.34±0.18, 2.2±0.28, 1.91±0.25, and 2.42 ±0.19, respectively. On the whole, differences between rotary-laser and rotary groups, step-back, and the three other techniques (rotary, laser, and rotary-laser) were significant at p=0.034. Based on the findings of this study, the cleaning efficacy of rotary, laser, and rotary-laser techniques were better than the step-back technique and the combined laser and rotary technique was the most efficient method.

Elemental analysis of dental hard tissues is of importance. The aim of this study is to evaluate X-ray microanalysis (XRMA) of bovine enamel in a scanning electron microscope (SEM) with different coatings. The buccal surface of bovine incisors was polished flat, one-third was coated with carbon, one-third with gold, leaving one-third uncoated for XRMA in an SEM equipped with an energy-dispersive microanalysis system. The elements oxygen, sodium, magnesium, phosphorous, chlorine, potassium, and calcium were analyzed using their respective characteristic K X-ray series. Comparisons were made with analyses of glass produced by fusion of the bovine enamel, showing that oxygen analyses using the K X-ray series are reliable and preferable to calculating oxygen by stoichiometry for natural enamel. For the gold-coated and uncoated analyses, carbon was also measured using the K X-ray series. Small area Analyses in small areas (80 × 80 μm) in variable pressure-SEM mode with low vacuum (20 Pa), without any coating, midway between 40 μm wide gold lines 140 μm apart to avoid build-up of electrostatic charge is the preferred method, especially if carbon is included in the analysis. The analyses of bovine enamel are sufficiently reproducible to be regarded as quantitative for all elements except carbon.

Over the past decade, knowledge about the ocular surface in glaucoma has significantly increased through the use of in vivo laser scanning confocal microscopy (LSCM). This in vivo imaging method can show modifications at the cellular level induced by anti-glaucoma drugs on ocular surface structures and adnexa in the eye. High-quality images of the conjunctiva, cornea, limbus, meibomian glands, and lymphoid structures during therapy can be obtained. In addition, LSCM opened new fields of research on the patho-physiology of aqueous humor (AH) hydrodynamics in untreated, and in medically or surgically treated glaucomatous patients. In these conditions, an enhancement of the trans-scleral AH outflow contributed to clarification of the mechanism of action of different anti-glaucoma medications and surgical approaches. Finally, the use of LSCM represented a huge advance in evaluation of bleb functionality after filtration surgery, defining the hallmarks of AH filtration through the bleb-wall and distinguishing functional from nonfunctional blebs. Thus, signs seen with LSCM may anticipate clinical failure, guiding the clinician in planning the appropriate timing of the various steps in bleb management. In this review we summarize the current knowledge about in vivo LSCM of the ocular surface in glaucoma.

A versatile method to fabricate taper-free micro-/nanopillars of large aspect ratio was developed with focused ion beam (FIB) cutting. The key features of the fabrication are a FIB with an incident angle of 90° to the long axis of the pillar that enables milling of the pillar sideways avoiding tapering and the FIB current can be reduced step by step so as to reduce possible radiation damage of the milled surface by Ga ions. A procedure to accurately determine the cross-section of each pillar was developed.

Sample preparation and imaging techniques for scanning electron microscopy (SEM) of dehydrated dental samples can hinder the structural analyses. This study qualitatively evaluated images obtained with two different protocols of SEM preparation and analysis to assess the dentine adhesive interface. The crown and root dentine of 12 bovine incisors were subjected to cementation with the resin cement RelyX U100 or RelyX ARC/SBMP (n = 6). After storage for 7 days in a moist environment at 37 ± 1°C, the dentine samples were dehydrated in an ascending alcohol series, and three specimens from each group were coated with gold or carbon and examined in a high-vacuum (JEOL JSM—6360LV, 10 kV) or low-vacuum (FEI Quanta 200F, 15–30 kV) microscope. Images were obtained at magnifications between 50 and 2,000×, but with different working distances. The use of high vacuum for carbon and gold coating and SEM visualization led to cracks in the samples. A small number of cracks can be described in the specimens subjected to the low-vacuum technique. The protocol for SEM imaging in low vacuum was considered more appropriate for preservation of the integrity of the evaluated structures.

An alternative focused ion beam preparation method is used for sampling historical photographs containing metallic nanoparticles in a polymer matrix. We use the preparation steps of classical ultra-microtomy with an alternative final sectioning with a focused ion beam. Transmission electron microscopy techniques show that the lamella has a uniform thickness, which is an important factor for analytical transmission electron microscopy. Furthermore, the method maintains the spatial distribution of nanoparticles in the soft matrix. The results are compared with traditional preparation techniques such as ultra-microtomy and classical focused ion beam milling.

This work presents a systematic study that evaluates the feasibility and reliability of local band gap measurements of Cu(In,Ga)Se2 thin films by valence electron energy-loss spectroscopy (VEELS). The compositional gradients across the Cu(In,Ga)Se2 layer cause variations in the band gap energy, which are experimentally determined using a monochromated scanning transmission electron microscope (STEM). The results reveal the expected band gap variation across the Cu(In,Ga)Se2 layer and therefore confirm the feasibility of local band gap measurements of Cu(In,Ga)Se2 by VEELS. The precision and accuracy of the results are discussed based on the analysis of individual error sources, which leads to the conclusion that the precision of our measurements is most limited by the acquisition reproducibility, if the signal-to-noise ratio of the spectrum is high enough. Furthermore, we simulate the impact of radiation losses on the measured band gap value and propose a thickness-dependent correction. In future work, localized band gap variations will be measured on a more localized length scale to investigate, e.g., the influence of chemical inhomogeneities and dopant accumulations at grain boundaries.

Mimetite, Pb5(AsO4)3Cl, is a ubiquitous mineral that is of interest in various fields such as ore mineralogy, environmental studies, and minerals engineering. Mimetite generally forms hexagonal prisms and barrel-shaped crystals, but its fibrous form is quite an uncommon one. Here we attempt to present its worldwide occurrences on the basis of a literature review. We then present a study on fibrous mimetite from one of its historical locations based on the petrographic microscope, SEM-SE and EDX, and Raman spectroscopy.

Currently there are no methods available for staining rat and human myocardial microvasculature on thick sections that would allow for specific staining and differentiation of arterioles, venules, and capillaries. A non-injection technique is described that allows for labeling of the microvascular bed (MVB) in formalin-fixed pieces of the myocardium from humans and the white rat Rattus norvegicus, as well as human full-mount pericardium. Vessel staining is based on the activity of phosphatases (ATPases) and the precipitation of the released phosphate with calcium ions at high pH (pH 10.5–11.5). The resulting precipitate subsequently is converted to black or brown lead sulfide. The specificity of this reaction to vessels of the MVB allows arterioles, venules, capillaries, and pre- and postcapillaries to be clearly visualized in thick (60–100 µm) and ultra-thick (300–500 µm) sections against an unstained background of muscle and connective tissue. In addition, smooth muscle cells of arterioles are also stained allowing for differentiation between arteriolar and venular beds. These observations have not been reported in rat or human myocardium using other methods. This procedure should benefit studies of coronary microcirculation in experimental and pathological conditions, as well as in pharmacological investigations.

The analytical performance of high-resolution scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDX) for accurate determination of the size, size distribution, qualitative elemental analysis of nanoparticles (NPs) was systematically investigated. It is demonstrated how powerful high-resolution SEM is by using both mono- and bi-modal distributions of SiO2 airborne NPs collected on appropriate substrates after their generation from colloidal suspension. The transmission mode of the SEM (TSEM) is systematically employed for NPs prepared on thin film substrates such as transmission electron microscopy grids. Measurements in the transmission mode were performed by using a “single-unit” TSEM transmission setup as manufactured and patented by Zeiss. This alternative to the “conventional” STEM detector consists of a special sample holder that is used in conjunction with the in-place Everhart–Thornley detector. In addition, the EDX capabilities for imaging NPs, highlighting the promising potential with respect to exploitation of the sensitivity of the new large area silicon drift detector energy dispersive X-ray spectrometers were also investigated. The work was carried out in the frame of a large prenormative VAMAS (Versailles Project on Advanced Materials and Standards) project, dedicated to finding appropriate methods and procedures for traceable characterization of NP size and size distribution.

A study by electron microscopy techniques of the structural and compositional properties of AlxGa1-xN/GaN nanowire (NW) heterostructures on Si(111) is presented. AlxGa1-xN depositions grown without catalyst by plasma-assisted molecular beam epitaxy were designed to form NWs in the range of 0.20<x<0.40 with different lengths and growth temperatures. The NWs exhibit a well-defined core-shell radial structure with a complex chemical distribution along and across the growth direction that finally affects the NW morphology. All the wires have an initial stage with a maximum Al content in the core slightly above the GaN/AlxGa1-xN interface, which initially decreases exponentially with the NW height depending on the nominal Al content and the growth temperature. In longer NWs, this trend changes and evolves increasing both the Al/Ga ratio and the core diameter as well as sharpening the shell. Adatom surface kinetic differences and the geometrical shadow effect during the growth are the probable drivers of this behavior.

Some image analysis techniques are developed for simplifying lattice fringe images of deposited pyrocarbon in carbon/carbon composites by chemical vapor infiltration. They are mainly the object counting method for detecting the optimum threshold, the self-adaptive morphological filtering, the node-separation technique for breaking the aggregate fringes, and some post processing algorithms for reconstructing the fringes. The simplified fringes are the foundation for defining and extracting quantitative nanostructure parameters of pyrocarbon. The frequency filter window of a Fourier transform is defined as the circular band that retains only those fringes with interlayer distance between 0.3 and 0.45 nm. Some judge criteria are set to define topological relation between fringes. For example, the aspect ratio and area of fringes are employed to detect aggregate fringes. Fringe coaxality and distance between endpoints are used to judge the disconnected fringes. The optimum values are determined by using the iterative correction techniques. The best cut-off value for the short fringes is chosen only when there is a reasonable match between the mean fringe length and the value measured by X-ray diffraction. The adopted techniques have been verified to be feasible and to have the potential to convert the complex lattice fringe image to a set of distinct fringe structures.

A better knowledge of synovial fluid (SF) ultrastructure is required to further understand normal joint lubrication and metabolism. The aim of the present study was to elucidate SF structural features in healthy joints from three mammalian species of different size compared with features in biomimetic SF. High-resolution structural analysis was performed using transmission electron microscopy (TEM) and scanning electron microscopy (SEM) and environmental SEM/wet scanning transmission electron microscopy mode complemented by TEM and SEM cryogenic methods. Laser-scanning confocal microscopy (LCM) was used to locate the main components of SF with respect to its ultrastructural organization. The present study showed that the ultrastructure of healthy SF is built from a network of vesicles with a size range from 100 to a few hundred nanometers. A multilayered organization of the vesicle membranes was observed with a thickness of about 5 nm. LCM study of biological SF compared with synthetic SF showed that the microvesicles consist of a lipid-based membrane enveloping a glycoprotein gel. Thus, healthy SF has a discontinuous ultrastructure based on a complex network of microvesicles. This finding offers novel perspectives for the diagnosis and treatment of synovial joint diseases.

Species of Haliotis (abalone) show high variety in structure and mineralogy of the shell. One of the European species (Haliotis tuberculata) in particular has an unusual shell structure in which calcite and aragonite coexist at a microscale with small patches of aragonite embedded in larger calcitic zones. A detailed examination of the boundary between calcite and aragonite using analytical microscopies shows that the organic contents of calcite and aragonite differ. Moreover, changes in the chemical composition of the two minerals seem to be gradual and define a micrometric zone of transition between the two main layers. A similar transition zone has been observed between the layers in more classical and regularly structured mollusk shells. The imbrication of microscopic patches of aragonite within a calcitic zone suggests the occurrence of very fast physiological changes in these taxa.

Transmission electron microscopes regularly produce data which has a dynamic range that exceeds the capabilities of the recording media used, particularly in diffraction patterns. Hardware solutions such as readable phosphor imaging plates have existed since the 1990s, but in recent years the advent of robust CCD digital cameras capable of capturing high intensities in a transmission electron microscope has made image acquisition fast and straightforward. However, all CCD cameras have a saturation limit, making imaging of low intensities difficult when an image is dominated by strong features. Here we present a simple and effective tool to overcome this limitation through acquisition of multiple images and software processing to produce high dynamic range electron images.

In GaAs-based pseudomorphic high-electron mobility transistor device structures, strain and composition of the InxGa1−xAs channel layer are very important as they influence the electronic properties of these devices. In this context, transmission electron microscopy techniques such as (002) dark-field imaging, high-resolution transmission electron microscopy (HRTEM) imaging, scanning transmission electron microscopy-high angle annular dark field (STEM-HAADF) imaging and selected area diffraction, are useful. A quantitative comparative study using these techniques is relevant for assessing the merits and limitations of the respective techniques. In this article, we have investigated strain and composition of the InxGa1−xAs layer with the mentioned techniques and compared the results. The HRTEM images were investigated with strain state analysis. The indium content in this layer was quantified by HAADF imaging and correlated with STEM simulations. The studies showed that the InxGa1−xAs channel layer was pseudomorphically grown leading to tetragonal strain along the [001] growth direction and that the average indium content (x) in the epilayer is ~0.12. We found consistency in the results obtained using various methods of analysis.

Bumblebees need to keep bodily homeostasis and for that have an efficient system of excretion formed by the Malpighian tubules, ileum, and rectum. We analyzed the excretory organs of Bombus morio, a bee without rectal pads. In addition, we analyzed the rectal epithelium of Melipona quadrifasciata anthidioides which has rectal pads. The Malpighian tubules exhibited two cell types and the ileum four types. However, comparative analysis of the rectum showed that only cells of the anterior region of the rectal epithelium of B. morio are structurally distinct. We suggest that cells of the Malpighian tubules of B. morio have an excretory feature and that cells of ileum have different functions, such as ion absorption and water, organic compound, and protein secretion. In addition, only the anterior region of the rectum of B. morio showed characteristic absorption. We suggest that Malpighian tubules participate in the excretion of solutes and that the ileum and rectal epithelium are responsible for homeostasis of water and solutes, compensating for the absence of rectal papillae. These results contribute to our understanding of the morphophysiology of the excretory organs of bees without rectal pads.

Analytical transmission electron microscopy (ATEM) offers great flexibility in identification of the structural—chemical organization of soft materials at the level of individual macromolecules. However, the determination of mechanical characteristics such as hardness/elasticity of the amorphous and polycrystalline organic substances by ATEM has been problematic so far. Here, we show that energy filtered TEM (EFTEM) measurements enable direct identification and study of mechanical properties in complex (bio-)polymer systems of relevance for different industrial and (bio-)medical applications. We experimentally demonstrate strong correlations between hardness/elasticity of different polymers (polycaprolactone, polylactid, polyethelene, etc.) and their volume plasmon energy. Thickness and anisotropy effects, which substantially mask the material contrast in EFTEM bulk plasmon images, can be adequately removed by normalizing the latter by carbon elemental map. EFTEM data has been validated using atomic force microscopy phase images, where phase shift related to the hardness and elastic modulus of the materials.