The development of laser wakefield accelerators (LWFA) over the past several years has led to an interest in very compact sources of X-ray radiation – such as “table-top” free electron lasers. However, the use of conventional undulators using permanent magnets also implies system sizes which are large. In this work, we assess the possibilities for the use of novel mini-undulators in conjunction with a LWFA so that the dimensions of the undulator become comparable with the acceleration distances for LWFA experiments (i.e., centimeters). The use of a prototype undulator using laser machining of permanent magnets for this application is described and the emission characteristics and limitations of such a system are determined. Preliminary electron propagation and X-ray emission measurements are taken with a LWFA electron beam at the University of Michigan.

To produce pulses with good flat-top quality, pulse-forming lines (PFLs) have been widely used in the field of Tesla-type pulse generators. To shorten the physical length of the PFL, a double-width PFL (DWPFL) is proposed that doubles the output pulse width while maintaining flat-top quality. A repetitively 10 GW Tesla-type long-pulse generator producing pulses with flat-top width of about 110 ns was developed with a coaxial DWPFL to produce high-current electron beams. Electron beams of about 10 GW with flat-top widths of about 110 ns were obtained on a planar vacuum diode load. With this pulse generator and a C-band high-power microwave system, microwaves of ~2.2 GW power and full-width at half-maximum of 101 ns were generated. The experiment demonstrates the feasibility and ideal output waveform quality of the DWPFL.

This paper provides a summary of recent research connected with the shock ignition (SI) concept of the inertial confinement fusion which was carried out at PALS. In the experiments, Cu planar targets coated with a thin CH layer were used. Two-beam irradiation experiment was applied to investigate the effect of preliminary produced plasma to shock-wave generation. The 1ω or 3ω main beam with a high intensity >1015 W/cm2 generates shock wave, while the other 1ω beam with the intensity below 1014 W/cm2 creates CH pre-plasma simulating the pre-compressed plasma related to SI. Influence of laser wavelength on absorbed energy transfer to shock wave was studied by means of femtosecond interferometry and measuring the crater volume. To characterize the hot electron and ion emission, two-dimensional (2D) Kα-imaging of Cu plasma and grid collector measurements were used. In single 1ω beam experiments energy transport by fast electrons produced by resonant absorption made a significant contribution to shock-wave pressure. However, two-beam experiments with 1ω main beam show that the pre-plasma is strongly degrading the scalelength which leads to decreasing the fast electron energy contribution to shock pressure. In both the single 3ω beam experiments and the two-beam experiments with the 3ω main beam, do not show any clear influence of fast electron transport on shock-wave pressure. The non-monotonic behavior of the scalelength at changing the laser beam focal radius in both presence and absence of pre-plasma reflects the competition of plasma motion and electron heat conduction under the conditions of one-dimensional and 2D plasma expansion at large and small focal radii, respectively.

The generalized theory of terawatt laser pulse interaction with a low-dense porous substance of light chemical elements including laser light absorption and energy transfer in a wide region of parameter variation is developed on the base of the model of laser-supported hydrothermal wave in a partially homogenized plasma. Laser light absorption, hydrodynamic motion, and electron thermal conductivity are implemented in the hydrodynamic code, according to the degree of laser-driven homogenization of the laser-produced plasma. The results of numerical simulations obtained by using the hydrodynamic code are presented. The features of laser-supported hydrothermal wave in both possible cases of a porous substance with a density smaller and larger than critical plasma density are discussed along with the comparison with the experiments. The results are addressed to the development of design of laser thermonuclear target as well as and powerful neutron and X-ray sources.

Iron (Fe) targets are exposed to 100 pulses of Nd: YAG laser (532 nm, 6 ns, 10 Hz) at various fluences ranging from 4.8 to 38.5 J/cm2. In order to explore the effect of background environment, targets have been exposed under vacuum as well as under five different pressures ranging from 5 to 100 Torr of various background gases like Ar, Ne, O2, and air. The sputtering yield measurements and surface modifications of laser-ablated Fe are explored by quartz crystal microbalance (QCM) and scanning electron microscopy (SEM) analysis, respectively. QCM measurements reveal that the sputtering yield of Fe is strongly affected by laser fluence, pressure and nature of gas. By increasing laser fluence, the sputtering yield initially increases due to enhanced energy deposition and then saturates due to self-regulating regime. However, with increasing pressures of background gases, the sputtering yield of Fe initially increases and then decreases. Owing to thermal conductivity, ionization potential, and mass of background gas, the sputtering yield of Fe varies in accordance with the sequence vacuum >Ar>Ne>O2> air. The SEM analysis reveals the formation of several features like laser-induced periodic surface structures, cones, cavities, channels, multiple ablative craters, and dot-like structures. The difference in the periodicity, size, and shape of features is explained on the basis of confinement and shielding effects of plasma and various energy deposition mechanisms. The surface profilometry analysis reveals that the crater depth increases with increasing the laser fluence in inert environments, while in case of reactive environments, it tends to decrease initially and afterwards it increases. X-ray diffraction and energy-dispersive X-ray analyses confirm the oxide formation in case of Fe treatment in O2 and air; however, no additional phases are observed for Fe irradiation under inert environments.

Surface exfoliation was observed on single-crystal silicon surface under the action of compressed plasma flow (CPF). This phenomenon is mainly attributed to the strong transient thermal stress impact induced by CPF. To gain a better understanding of the mechanism, a micro scale model combined with thermal conduction and linear elastic fracture mechanics was built to analyze the thermal stress distribution after energy deposition. After computation with finite element method, J integral parameter was applied as the criterion for fracture initiation evaluation. It was demonstrated that the formation of surface exfoliation calls for specific material, crack depth, and CPF parameter. The results are potentially valuable for plasma/matter interaction understanding and CPF parameter optimization.

By using reductive perturbation technique we have studied the linear and non-linear properties of ion-acoustic solitary structures in a three-component plasma containing non-thermal electrons and Boltzmann positrons and a comparatively cold ion which has got a streaming motion. The Korteweg–de Vries equation has been obtained and the dependence of small amplitude solitary structures on various plasma parameters such as streaming velocity (v0), non-thermal parameter (β), reciprocal of electron temperature (χ), positron density (p), Mach number (M), and ion density (δ) have been studied. The possibility of formation of enveloping soliton and its characteristic features are further investigated by deriving the non-linear Schrödinger equation.

Integrated simulation results of femtosecond laser ablation of copper were compared with new experimental data. The numerical analysis was performed using our newly developed FEMTO-2D computer package based on the solution of the two-temperature model. Thermal dependence of target optical and thermodynamic processes was carefully considered. The experimental work was conducted with our 40 fs 800 nm Ti:sapphire laser in the energy range from 0.14 mJ to 0.77 mJ. Comparison of measured ablation profiles with simulation predictions based on phase explosion criterion has demonstrated that more than one ablation mechanisms contribute to the total material removal even in the laser intensity range where explosive boiling is dominating. Good correlation between experimental and simulation results was observed for skin depth and hot electron diffusion depth – two parameters commonly considered to identify two ablation regimes in metal. Analysis of the development dynamics for electron–lattice coupling and electron thermal conduction allowed explaining different ablation regimes because of the interplay of the two parameters.

Hermite–Gaussian (HG) laser beam with transverse electromagnetic (TEM) mode indices (m, n) of distinct values (0, 1), (0, 2), (0, 3), and (0, 4) has been analyzed theoretically for direct laser acceleration (DLA) of electron under the influence of an externally applied axial magnetic field. The propagation characteristics of a TEM HG beam in vacuum control the dynamics of electron during laser–electron interaction. The applied magnetic field strengthens the $\vec v \times \vec B$ force component of the fields acting on electron for the occurrence of strong betatron resonance. An axially confined enhanced acceleration is observed due to axial magnetic field. The electron energy gain is sensitive not only to mode indices of TEM HG laser beam but also to applied magnetic field. Higher energy gain in GeV range is seen with higher mode indices in the presence of applied magnetic field. The obtained results with distinct TEM modes would be helpful in the development of better table top accelerators of diverse needs.