Fullerene dimers have attracted extensive attention due to their unique structures and fascinating properties. Here, fullerene dimer derivatives with four to six carbon atoms in the esters are designed and synthesized. The property differences that caused by the carbon number in the esters of the fullerene dimers are investigated by performing their electrochemical, optical, and photoelectric measurements. As the carbon atom numbers in the esters increase from four to five and six, the absorption intensities increase to 1.6- and 4.4-folds. The intensities of the fluorescence spectra increase to 1.8- and 5.2-folds. Their photocurrent increases to 2- and 7-folds under the irradiation of a 405-nm laser. The LUMO energy levels move downward slightly from −3.89 to −3.90 and −3.92 eV, respectively. Our results indicate that as the carbon number increases, the carbon chain lengths in the ester structures increase, very slight effects produced on the energy levels of the fullerene dimers, but strongly contribute to their chemical activities and thus the photoelectronic efficiencies.

Using the first-principles calculation combined with the structure searching method, the ternary intermetallic compound (IMC) (Ni0.66, Zn0.33)3Sn4 with $R\bar 3m$ space group is predicted. The energetic, dynamic, thermal, and mechanical stabilities of the (Ni0.66, Zn0.33)3Sn4 IMC are confirmed. The mechanical, thermodynamic, and electronic characteristics at different pressures from 0 to 20 Gpa for the (Ni0.66, Zn0.33)3Sn4 IMC are also investigated. The results show that the (Ni0.66, Zn0.33)3Sn4 IMC possesses a ductile trait within 20 Gpa and that pressurization can increase its elastic modulus, hardness, anisotropy, Debye temperature, and minimum thermal conductivity. At a given pressure, the thermal expansion coefficient α increases significantly below 200 K, and then its increase rate approaches a linear mode as the temperature increases. Compared with the case of 0 GPa, the shapes of the total density of states and partial density of states for the (Ni0.66, Zn0.33)3Sn4 IMC change slightly at pressure 20 Gpa, implying that its structure is still stable under pressure 20 GPa.

Three-dimensional nano-mulberries consisting of SnO2 nanoparticles have been successfully anchored onto the surfaces of reduced graphene oxide (RGO) to construct hierarchical hybrids—SnO2@RGO with a one-pot approach. The SnO2 nano-mulberries with different amounts of RGO have been produced for optimizing their composition effect on Li storage performance. Specifically, SnO2@RGO hybrids incorporated with optimized amount of RGO nanosheets (∼20.8%) exhibit highly enhanced capacity of ∼1025 mA h/g at 0.1 A/g and a reversible capacity of 750 mA h/g over 100 cycles at 0.2 A/g. The materials also deliver much better rate performance with average specific capacity of ∼498 mA h/g at 2 A/g in comparison with that of SnO2 nano-mulberries. After cycling for 600 times at 1 A/g, the SnO2@RGO electrodes still maintain high reversible capacity of ∼602 mA h/g, corresponding to 35% of the second cycle and 133% of the 70th discharge capacity.

In this work, filament based on ɛ-polycaprolactone (PCL) and containing the bioactive ceramics nanohydroxyapatite (nHap) and Laponite® (Lap) was prepared by the extrusion process. To obtain the material, a mass ratio of 89:10:1 (PCL:nHap:Lap) was used, and structural and morphological characterization was realized. In addition, cytotoxicity (using Allium cepa bulbs) and viability tests on L929 cells also were performed. The results showed that filament (diameter of 1.79 ± 0.17 mm) presented a good dispersion of nHap and Lap into polymeric matrices. Fourier transform infrared spectroscopy identified typical bands at 1720, 1091, and 1045 cm−1 addressed to PCL and nHAp, In addition, Lap was identified through dispersive energy system and X-ray diffraction analyses. All filaments did not exhibit cytotoxic effects.

The synergetic effects of surface smoothing exhibited during the inductively coupled plasma reactive ion etching (ICP-RIE) of free-standing polycrystalline diamonds (PCDs) were investigated. Changing the assistive gas types generated variable surface oxidation states and chemical environments that resulted in different etching rates and surface morphologies. The main reaction bond mechanism (C–O) during ICP-RIE and the ratio of C–O–C/O–C=O associated with the existence of a uniform smooth surface with root mean square (RMS) roughness of 2.36 nm were observed. An optimal process for PCD smoothing at high etching rate (4.6 μm/min) was achieved as follows: 10% gas additions of CHF3 in O2 plasma at radio frequency power of 400 W. The further etched ultra-smooth surface with RMS roughness <0.5 nm at etching rate of 0.23 μm/min that being produced by transferring this optimum recipe on single crystal diamonds with surface patterns confirmed the effectiveness of the fast smoothing approach and its feasibility for diamond surface patterning.

A novel ionic liquid/α-ZrP (C16MIM/α-ZrP) lamellar nanocomposite was fabricated via the electrostatic self-assembly deposition technique by using exfoliated α-ZrP nanosheets and guest molecules (1-hexadecyl-3-methylimidazolium bromide) as building blocks under mild conditions. C16MIM/α-ZrP nanocomposite was characterized by various analytical techniques such as X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscope (SEM), Fourier transform infrared spectroscopy, and synchronous thermal analyzer. The net interlayer spacing of α-ZrP determined by XRD confirmed that the C16MIM cations formed a monolayer arrangement between the α-ZrP nanosheets. The morphology and microstructure of C16MIM/α-ZrP composite were observed using SEM and TEM. The C16MIM/α-ZrP modified glass carbon electrode exhibited excellent electrocatalytic activity toward the oxidation of nitrite in weak base media. The results obtained with differential pulse voltammetry demonstrated that the C16MIM/α-ZrP hybrid detected nitrite linearly in the concentration range from 7.3 μM to 1.25 mM with the detection limit of 1.26 μM (S/N = 3). Additionally, the prepared sensor showed outstanding reproducibility, high stability, and anti-interference capability.

The analysis presented in Part I of this study on the binary collision of equal molten calcium–magnesium–alumino–silicate (CMAS) droplets is extended to investigate the flow and interfacial dynamics of unequal CMAS droplet collision. Numerical investigations of head-on, off-center, and grazing collisions of two CMAS droplets of size 1 and 2 mm are conducted at pressure and temperature of 20 atm and 1548 K, respectively, that are representative of a gas-turbine combustor. At these conditions, the physical properties of CMAS are density, ρCMAS = 2690 kg/m3, surface tension between CMAS/air, σCMAS = 0.40 N/m, and viscosity, μCMAS = 11.0 N-s/m2. The primary difference between the CMAS and a fictitious fluid with viscosity 1/10 of CMAS was higher deformation for the lower viscosity case, leading to stretching and subsequent breakup of the liquid structure. These mechanisms are supported by the time evolution of surface, kinetic, and viscous dissipation energies.

Some interesting properties such as superelasticity, shape memory effect, kink resistance, good biocompatibility, biomechanical properties, and corrosion resistance made nitinol a popular biomaterial as stent and orthopedic implants. But surface modification is needed to control nickel leaching from its surface, making safe for human body. The aim of this study was to modify the nitinol surface by the silanization technique and electrophoretically deposited hydroxyapatite coating, and to conduct a detailed in vitro and in vivo investigation. Detailed in vitro investigation involved MTT assay with the human osteoblastic cells (MG63 cell) over a period of 5 days and confocal image study. In case of in vivo study, histological study, fluorochrome labeling study, and Micro-Ct study were conducted. The overall in vitro and in vivo results indicate that silanized nitinol samples are showing slightly better level of performance, but both the surface-modified samples are suitable as the potential bio-implant for orthopedic purpose.

Epitaxial SnSxSe2−x films with tunable band gap energies (1.0–2.2 eV) are of growing interest for photodetectors and 2D heterostructures for nanoscale electronics. In this study, powder vapor transport growth of SnSxSe2−x was investigated on c-plane sapphire and epitaxial graphene (EG)/6H–SiC substrates using tin, sulfur, and selenium powder sources in a heated tube furnace. The SnSxSe2−x composition was controlled by varying the sulfur and selenium source temperatures and the corresponding chalcogen vapor pressure ratio. Raman spectroscopy was used to determine the alloy composition of the films, and the optical properties were characterized using UV-Vis-NIR spectroscopy. SnSxSe2−x grown on sapphire consisted of vertically oriented platelets. By contrast, large-area, planar coalesced SnSxSe2−x films grew on EG with low surface roughness indicative of a van der Waals growth mode. High-resolution X-ray diffraction θ–2θ scans and pole figure analysis confirm that the SnSxSe2−x films are c-axis oriented with epitaxial relation being $\left[ {11\bar{2}0} \right]$ SnSxSe2−x‖$\left[ {10\bar{1}0} \right]$ 6H–SiC.

Methods that allow for high-throughput synthesis of magnetic nanoparticles are necessary to more feasibly fabricate materials for real-world applications. To accomplish this, in this article, we describe a versatile electrospray-based synthesis method for the synthesis of magnetic cobalt ferrite nanoparticles. This method has the potential to be readily scaled up using methods similar to those currently used in place for the large-scale electrospinning of fibers. To mitigate film formation as often seen with electrospraying ceramics onto a flat plate collector, we developed a method where the magnetic cobalt ferrite nanoparticles were electrosprayed into a silicone oil–based liquid collector. The as-sprayed particles were then crystalized by salt calcining with sodium chloride at 800 °C. The synthesized magnetic nanoparticles obtained using this method had an average particle diameter of 20.7 ± 11.5 nm. This liquid collection method for the synthesis of cobalt ferrite also presents a versatile platform for the synthesis of a wide range of functional nanomaterials and nanocomposites.

The present work is mainly accentuated to improve corrosion resistance performance, adhesion strength, biocompatibility, and cell proliferation of metallic implants. Novel nano triphasic bioceramic composite coating was achieved on 316L SS by the electrophoretic deposition process followed by vacuum sintering. The optimized potential for composite coating on 316L SS was found to be 30 V and 1 min. All the composite coated samples were sintered in a vacuum furnace at various sintering temperature starting from 700 °C to 1000 °C for 1 h. The coated samples were thoroughly characterized in terms of crystallinity, morphology, and surface roughness by XRD, FESEM with EDX, and profilometer studies, respectively. In addition, the coated samples were mechanically characterized using a tap adhesion and Vickers microhardness test. Corrosion performance of the coated sample was characterized by electrochemical studies in Hank's solution. The in vitro cytotoxicity studies for cell viability and cell proliferation was carried out using MC3T3-E1 osteoblast cells. These studies revealed an enhanced cell attachment and proliferation on the composite-coated sample than the uncoated sample, which controlled the discharge of metal ions from the metal surface into the biological system.

Structural evolution induced and driven by a dual system and simultaneous passivation of phosphorene are reported. Different nano-objects of phosphorene or black phosphorus (BP) are obtained using a new method of exfoliation, in which solvent and an ionic polymer are combined to weaken the van der Waals forces and to scissor the nanosheets. Nanoribbons, nanorods, and nanoneedles are obtained under mechanical force and ambient conditions. Ionic polymer chains assist in curling the monolayer or few-layer nanosheet. Nafion is chosen to exfoliate the bulk BP and induce a morphological transition in BP nanosheets. The exfoliation of BP nanosheets results into thin and specific structures such as nanosheets/rods/needles. The nanosheets of phosphorene are covered and passivated simultaneously by the polymeric sheath that protects the nanosheets from degradation or oxidation and can be integrated with a device directly without any further coating.

This study presents a dual Eulerian–Lagrangian particle approach for time-accurate computational fluid dynamics (CFD) modeling of volcanic ash in gas turbine engines and initial results. The objective is to enable high-fidelity simulations of calcia–magnesia–alumina-silica (CMAS) particles in gas turbine engines to better predict deposition and particle paths to rapidly test mitigation solutions. The approach uses a primarily first principles framework to account for the various physical phenomena in the system. Particles are modeled using Lagrangian methods which track individual particles and Equilibrium Eulerian methods which track particles in terms of concentration densities. Lagrangian methods become prohibitively expensive for fine particles. Eulerian methods are physically appropriate for fine particles but become inaccurate for large particle sizes. A dual approach using both Eulerian and Lagrangian methods allows for optimal computational cost with maximum accuracy. Simulation results using the proposed approach are compared against experimental data for a representative gas turbine engine blade.

A flexible surface-enhanced Raman scattering (SERS) substrate was prepared by vacuum evaporation of silver on the surface of woven nylon fabrics. SERS properties of the Ag-coated nylon fabrics varied as the thickness of silver coatings changed, relative to the morphologies and distribution of silver nanoparticles (NPs) on fiber. The SERS enhancement performance of Ag-coated nylon fabrics was evaluated by collecting Raman signals of different concentrations of p-aminothiophenol (PATP). The results suggested that the nylon fabrics coated with 10 nm thickness Ag NPs coatings possessed high SERS activity and its detection concentration for PATP is as low as 10−9 M. Furthermore, sensitive SERS signals with excellent reproducibility (Relative standard deviation = 8.25%) and stability (30 days) have been demonstrated. In addition, the SERS nylon fabrics have been applied to rapidly detect thiram pesticides on cucumber, which indicated a great potential for trace analysis.

In this paper, CNTs reinforced foam aluminum matrix composites with small pore diameter were prepared by powder metallurgy method. When the mass fraction of CNTs was 0.75%, the tensile strength, flexural strength and compressive yield strength of the materials were 3.4 times, 2.4 times and 2.4 times of pure foam aluminum, respectively, reaching the maximum value, which obviously improved the mechanical properties of aluminum foam. The tensile property model of foam aluminum matrix composites was built to predict the properties of the composites, and the effects of defects and reinforcement on the mechanical properties of the composites were compared. The results show that the tensile fitting is consistent with the measured results when the mass fraction of CNTs is less than 0.75%, but the weakening effect of defects on the strength of aluminum foam is much greater than the enhancement of CNTs. With the increase of CNTs mass fraction, the damping loss factor of foam aluminum composites increases, dislocation damping and grain boundary damping play a role in advance, and the damping peak moves to the low temperature region.

The synthesis of antibacterial biomaterial with specific functions responsive to specific bacterial growth environments is of significant importance to achieve effective sterilization and reduce the resistant bacteria. Herein, inspired by biomineralization, we develop a one-pot, threonine (Thr)-mediated biomineralization method using a CO2 bubbling procedure to green, simply and quickly prepare vaterite CaCO3 microspheres as a platform for antibacterial Sanguinarine (SAN) delivery. The loading capacity of vaterite CaCO3 microspheres for SAN drugs reached 159.8 mg/g, corresponding to the loading efficiency of 83.7%. And for the first time, a novel Sanguinarine@calcium carbonate (SAN@CaCO3) organic–inorganic hybrid antibacterial biofilm was constructed by using vaterite CaCO3 microspheres with pH-responsive and high SAN drug-loading. Importantly, the film showed bacteria-triggered, pH-responsive SAN release properties and strong bactericidal ability (96.19%) for Staphylococcus aureus (S. aureus). Meanwhile, it also had antibacterial capabilities in real environments. In 7 days, it can significantly inhibit the adhesion and growth of bacteria in the air. The biomineralized synthetic vaterite CaCO3 microspheres and the application in the construction of pH-responsive antibacterial biofilm have bright future in resisting bacterial infections and reducing the production of resistant bacteria.

Since the photocatalytic effect of a single conventional photocatalyst is often not ideal, it is particularly important to design and construct an efficient and stable photocatalyst in a compound way. In this study, we exploited the sol–gel method to combine BiOCl and TiO2 and gave full play to their respective advantages to prepare BiOCl/TiO2 composite materials. Then, X-ray diffraction (XRD), scanning electron microscope (SEM), and transmission electron microscope (TEM) characterization techniques were utilized to study important indicators of composites—composition, morphology, and structure. In the photodegradation experiment of methyl orange (MO), it was found that the photocatalytic performance of 10BTO (the molar ratio of TiO2 to BiOCl is 10:1) was the best among all the composite photocatalysts, and almost complete degradation of MO was realized. Besides, repeated experiments and recyclability tests on composite materials display favorable stability. Through ultraviolet–visible diffuse reflectance spectroscopy (UV–Vis DRS), photoluminescence (PL), transient photocurrent response, electrochemical impedance spectroscopy (EIS), and electron spin resonance (ESR), a possible degradation mechanism is proposed. Given that there are serious environmental pollution problems in our country, we sincerely hope this research will do its best to degrade organic pollutants in wastewater.

Elevated temperature co-sputtering of immiscible elements results in a variety of self-organized morphologies due to phase separation. Cu–Ta is used as a model system to understand the evolution of phase-separated microstructural morphologies by co-sputtering thin films with nominal 50–50 at.% composition at four temperatures: 25, 400, 600, and 800 °C. Scanning/transmission electron microscopy of the film cross sections showed the microstructure morphology varied from nanocrystalline Cu–Ta at 25 °C to a wavy ribbon-like structure at 400 °C, to Cu-rich agglomerates surrounded by Ta-rich veins at 600 and 800 °C. In the agglomerate-vein morphology, microstructural features were present on two length scales, from a few nanometers to a few tens of nanometers, thus making the structures hierarchical. On the nanoscale, the Cu-rich agglomerates contained Ta precipitates, whereas the Ta-rich veins had embedded Cu nanocrystals. The various microstructures can be attributed to the highly disparate constituent element interdiffusion at the deposition temperatures with the Cu having orders of magnitude higher mobility than Ta at the deposition temperatures. This study of processing–microstructure relationship will be useful in guiding the design of hierarchical multiphase microstructures in binary or multicomponent thin films with tailored mechanical properties.

Metal additive manufacturing (AM) provides a platform for microstructure optimization via process control, but establishing a quantitative processing-microstructure linkage necessitates an efficient scheme for microstructure representation and regeneration. Here, we present a deep learning framework to quantitatively analyze the microstructural variations of metals fabricated by AM under different processing conditions. The principal microstructural descriptors are extracted directly from the electron backscatter diffraction patterns, enabling a quantitative measure of the microstructure differences in a reduced representation domain. We also demonstrate the capability of predicting new microstructures within the representation domain using a regeneration neural network, from which we are able to explore the physical insights into the implicitly expressed microstructure descriptors by mapping the regenerated microstructures as a function of principal component values. We validate the effectiveness of the framework using samples fabricated by a solid-state AM technology, additive friction stir deposition, which typically results in equiaxed microstructures.

With the ever-increasing importance of nanoscale deformation phenomena in contemporary technologies, basic understanding of material behavior at the nanoscale has become of critical importance. Especially, nanomechanical testing that provides the capability to study fundamental nanoscale deformation and phase change phenomena in real time and under controlled loading conditions is essential for nanomaterial research. In this study, acoustic emission (AE) was used in situ to characterize nanoindentation-induced deformation, microfracture, and phase transformation processes intrinsic of bulk single-crystal MgO and polycrystalline Al, thin films of polycrystalline SiC, and thick films of austenitic TiNi shape-memory alloy. Scale-dependent plastic deformation and microfracture affected by the indenter tip radius and the applied normal load are interpreted in terms of the type and intensity of AE events revealed by abrupt displacement excursions in the loading response of the indented materials. The amplitudes of AE waveforms are used to examine characteristic deformation, microfracture, and phase change mechanisms in the time domain. Fast Fourier transformation and short-time Fourier transformation analyses provide further insight into the material behavior and structural changes due to indentation loading in the frequency and time-frequency domain, respectively. The methodology developed in this study represents an effective approach for nanomechanical testing and in situ characterization of nanoscale deformation, microfracture, and phase transformation phenomena.