Thermal effects are typically considered as obstacles to high-repetition-rate stimulated Brillouin scattering (SBS) pulse compression. In this paper, a novel method is proposed for improving the SBS output characteristics by exploiting thermal effects on the liquid medium. Using HT270, the SBS output parameters with the medium purification and rotating off-centered lens methods are studied at different repetition rates. The results indicate that these two methods can alleviate thermal effects and improve the energy efficiency, but the rotating method reduces the energy stability because of the aggravated optical breakdown at the kilohertz-level repetition rate. For a 35-mJ pump energy, the energy efficiency at 2 kHz without the rotating method is 30% higher than that at 100 Hz and 70% higher than that at 500 Hz. The enhancement of the SBS output characteristics by thermal effects is demonstrated theoretically and experimentally, and 2-kHz high-power SBS pulse compression is achieved with HT270.

We evaluate and demonstrate ultra-broadband near-infrared noncollinear optical parametric amplification in two nonlinear crystals, bismuth borate (BiBO) and yttrium calcium oxyborate (YCOB), which are not commonly used for this application. The spectral bandwidth is of the microjoule level; the amplified signal is ≥ 200 nm, capable of supporting sub-10 fs pulses. These results, supported by numerical simulations, show that these crystals have a great potential as nonlinear media in both low-energy, few-cycle systems and high peak power amplifiers for terawatt to petawatt systems based on noncollinear optical parametric chirped pulse amplification (NOPCPA) or a hybrid.

Proton radiography is a key diagnostics to measure and image the electric/magnetic field in laser-produced plasmas. A thin solid target is irradiated with an intense laser pulse to produce a proton beam. The accelerated proton can achieve higher energy with thinner target. In order to produce an extremely thin target, we have developed a large-area suspended graphene as a laser target for energetic ion sources. We describe the manufacturing process of the suspended graphene, and show the results of quality evaluations.

Microtube implosions are a novel scheme to generate ultrahigh magnetic fields of the megatesla order. These implosions are driven by ultraintense and ultrashort laser pulses. Using two- and three-dimensional particle simulations where megatesla-order magnetic fields can be achieved, we demonstrate scaling and criteria in terms of laser parameters, such as laser intensity and laser energy, to facilitate practical experiments toward the realization of extreme physical conditions, which have yet to be realized in laboratories. Microtube implosions should provide a new platform for studies in fundamental and applied physics relevant to ultrahigh magnetic fields.

Tailored diode laser single emitters with long (6 mm) resonators and wide (1.2 mm) emission apertures that operate with 940 nm emission wavelength were assembled in novel edge-cooled vertically stacked arrays, and used to construct a compact and highly efficient fiber coupled pump source for Yb:YAG pulsed high-energy class solid-state lasers. The novel configuration is shown to allow repetition rates of 200 Hz at 1 ms pulse duration, at an output power of 130 W per single emitter. The emission of two stacked arrays was then optically combined to realize pump modules that deliver 6 kW peak power (pulse energy 6 J) from a 1.9 mm core diameter fiber, with wall plug efficiency of 50%. This represents a significant improvement in terms of duty cycle and electro-optical efficiency over conventional sources. The pump module has been successfully tested at the Max Born Institute, Berlin during trials for pumping of disk lasers.

We produced $5\text{-}{\rm\mu}\text{J}$, 6.5-fs visible pulses at a repetition rate of 1 kHz using filamentation in a gas cell filled with krypton followed by spectral selection and phase compensation by a combination of dielectric mirrors. The visible pulses have a smooth spectrum from 520 to 650 nm with a shot-to-shot stability in each spectral component of better than 2% (standard deviation). This pulse compression scheme is simple and robust, and can be easily integrated into intense ultrashort-pulse laser systems.

Emerging multi-PW-class lasers and their envisioned laser–plasma interaction applications in unprecedented intensity regimes set a very demanding frame for the precise understanding of the finest properties of these systems. In this work we present a synthesis of simulation studies on a series of less known or even completely disregarded spatiotemporal effects that could potentially impact greatly the performances of high-intensity lasers.

Laser-induced damage (LID) on high-power laser facilities is one of the limiting factors for the increase in power and energy. Inertial confinement fusion (ICF) facilities such as Laser Mégajoule or the National Ignition Facility use spectral broadening of the laser pulse that may induce power modulations because of frequency modulation to amplitude modulation conversion. In this paper, we study the impact of low and fast power modulations of laser pulses both experimentally and numerically. The MELBA experimental testbed was used to shape a wide variety of laser pulses and to study their impact on LID. A 1D Lagrangian hydrodynamic code was used to understand the impact of different power profiles on LID.

We report on the generation of a mid-infrared (mid-IR) frequency comb with a maximum average output power of 250 mW and tunability in the 2.7–4.0 μm region. The approach is based on a single-stage difference frequency generation (DFG) starting from a compact Yb-doped fiber laser system. The repetition rate of the near-infrared (NIR) comb is locked at 75 MHz. The phase noise of the repetition rate in the offset-free mid-IR comb system is measured and analyzed. Except for the intrinsic of NIR comb, environmental noise at low frequency and quantum noise at high frequency from the amplifier chain and nonlinear spectral broadening are the main noise sources of broadening the linewidth of comb teeth, which limits the precision of mid-IR dual-comb spectroscopy.

The laser system PALS, as a driver of a broad-beam ion source, delivered deuterons which generated neutrons with energies higher than 14 MeV through the $\def \xmlpi #1{}\def \mathsfbi #1{\boldsymbol {\mathsf {#1}}}\let \le =\leqslant \let \leq =\leqslant \let \ge =\geqslant \let \geq =\geqslant \def \Pr {\mathit {Pr}}\def \Fr {\mathit {Fr}}\def \Rey {\mathit {Re}}{}^{7}\mathrm{Li(d,n)}{}^{8}\mathrm{Be}$ reaction. Deuterons with sub-MeV energy were accelerated from the front surface of a massive $\mathrm{CD}_{2}$ target in the backward direction with respect to the laser beam vector. Simultaneously, neutrons were emitted from the primary $\mathrm{CD}_{2}$ target and a secondary LiF catcher. The total maximum measured neutron yield from ${}^{2}\mathrm{D(d,n)}{}^{3}\mathrm{He}$, ${}^{7}\mathrm{Li(d,n)}{}^{8}\mathrm{Be}$, ${}^{12}\mathrm{C(d,n)}{}^{13}\mathrm{N}$ reactions was ${\sim } 3.5 ({\pm }0.5) \times 10^{8}\ \mathrm{neutrons/shot}$.

Fast magnetic field annihilation in a collisionless plasma is induced by using TEM(1,0) laser pulse. The magnetic quadrupole structure formation, expansion and annihilation stages are demonstrated with 2.5-dimensional particle-in-cell simulations. The magnetic field energy is converted to the electric field and accelerate the particles inside the annihilation plane. A bunch of high energy electrons moving backwards is detected in the current sheet. The strong displacement current is the dominant contribution which induces the longitudinal inductive electric field.

In this paper, we propose an effective method to compensate for the performance degradation of optically addressed spatial light modulators (OASLMs). The thermal deposition problem usually leads to the on-off ratio reduction of amplitude OASLM, so it is difficult to achieve better results in high-power laser systems. Through the analysis of the laser-induced temperature rise model and the liquid crystal layer voltage model, it is found that reducing the driving voltage of the liquid crystal light valve and increasing the driving current of the optical writing module can compensate for the decrease of on–off ratio caused by temperature rise. This is the result of effectively utilizing the photoconductive effect of Bi12SiO20 (BSO) crystal. The experimental results verify the feasibility of the proposed method and increase the laser withstand power of amplitude-only OASLM by about a factor of 2.5.

We demonstrate an all-fiber high-power linearly polarized supercontinuum source with polarization-maintaining photonic crystal fibers (PM-PCFs) as the nonlinear medium. The source exhibits an average output power of 3.8 W with a flat spectrum from 480 nm to 2100 nm at the $-$10 dB level, except for the residual pump peak. The polarization extinction ratio (PER) is measured to be greater than 20 dB at selected sample wavelength points (532 nm, 1064 nm and 1550 nm) at the highest pump power level and greater than 20 dB at all wavelengths from 800 nm to 1500 nm at the low pump power level. We also experimentally study the spectral properties when the pump light propagates along different axes of the PM-PCF. The results show that propagating parallel to the slow axis enables a broader spectrum in the PM-PCF in this case, probably due to matching of the dispersion properties with the pump light, which is qualitatively in accordance with the numerical simulation. To our best knowledge, this is the first demonstration of a watt-level linearly polarized supercontinuum source generated from PM-PCFs in an all-fiber structure.

Laser–plasma interactions have been studied in detail over the past twenty years, as they show great potential for the next generation of particle accelerators. The interaction between an ultra-intense laser and a solid-state target produces a huge amount of particles: electrons and photons (X-rays and $\unicode[STIX]{x03B3}$-rays) at early stages of the process, with protons and ions following them. At SPARC_LAB Test Facility we have set up two diagnostic lines to perform simultaneous temporally resolved measurements on both electrons and protons.

Measured highly elevated gains of proton–boron (HB11) fusion (Picciotto et al., Phys. Rev. X 4, 031030 (2014)) confirmed the exceptional avalanche reaction process (Lalousis et al., Laser Part. Beams 32, 409 (2014); Hora et al., Laser Part. Beams 33, 607 (2015)) for the combination of the non-thermal block ignition using ultrahigh intensity laser pulses of picoseconds duration. The ultrahigh acceleration above $10^{20}~\text{cm}~\text{s}^{-2}$ for plasma blocks was theoretically and numerically predicted since 1978 (Hora, Physics of Laser Driven Plasmas (Wiley, 1981), pp. 178 and 179) and measured (Sauerbrey, Phys. Plasmas 3, 4712 (1996)) in exact agreement (Hora et al., Phys. Plasmas 14, 072701 (2007)) when the dominating force was overcoming thermal processes. This is based on Maxwell’s stress tensor by the dielectric properties of plasma leading to the nonlinear (ponderomotive) force $f_{\text{NL}}$ resulting in ultra-fast expanding plasma blocks by a dielectric explosion. Combining this with measured ultrahigh magnetic fields and the avalanche process opens an option for an environmentally absolute clean and economic boron fusion power reactor. This is supported also by other experiments with very high HB11 reactions under different conditions (Labaune et al., Nature Commun. 4, 2506 (2013)).

A new specially correlated partially coherent beam named nonuniform multi-Gaussian correlated (NMGC) partially coherent beam is introduced. The correlation functions of such beam in $x$ and $y$ directions are different from each other, i.e., nonuniform correlation function in one direction and multi-Gaussian correlated Schell-model function in the other direction. The propagation properties of an NMGC partially coherent beam in free pace are demonstrated, and we find that the intensity distribution of such beam exhibits self-focusing and self-shifting effect in one direction and self-shaping effect in the other direction on propagation. The correlation-induced self-focusing and self-shaping effect will be useful in some applications, where the high power and shaped laser is required, such as material thermal processing and laser carving.

Processes of laser energy absorption and electron heating in an expanding plasma in the range of irradiances $I\unicode[STIX]{x1D706}^{2}=10^{15}{-}10^{16}~\text{W}\,\cdot \,\unicode[STIX]{x03BC}\text{m}^{2}/\text{cm}^{2}$ are studied with the aid of kinetic simulations. The results show a strong reflection due to stimulated Brillouin scattering and a significant collisionless absorption related to stimulated Raman scattering near and below the quarter critical density. Also presented are parametric decay instability and resonant excitation of plasma waves near the critical density. All these processes result in the excitation of high-amplitude electron plasma waves and electron acceleration. The spectrum of scattered radiation is significantly modified by secondary parametric processes, which provide information on the spatial localization of nonlinear absorption and hot electron characteristics. The considered domain of laser and plasma parameters is relevant for the shock ignition scheme of inertial confinement fusion.

We demonstrated experimentally the formation of monoenergetic beams of accelerated electrons by focusing femtosecond laser radiation with an intensity of $2\times 1{0}^{17} ~\mathrm{W} / {\mathrm{cm} }^{2} $ onto the edge of an aluminum foil. The electrons had energy distributions peaking in the 0.2–0.8 MeV range with energy spread less than 20%. The acceleration mechanism related to the generation of a plasma wave as a result of self-modulation instability of a laser pulse in a dense plasma formed by a prepulse (arriving 12 ns before the main pulse) is considered. One-dimensional and two-dimensional Particle in Cell (PIC) simulations of the laser–plasma interaction showed that effective excitation of a plasma wave as well as trapping and acceleration of an electron beam with an energy on the order of 1 MeV may occur in the presence of sharp gradients in plasma density and in the temporal shape of the pulse.

As intense, ultrashort, kHz-repetition-rate laser systems become commercially available, pulse cumulative effects are critical for laser filament-based applications. In this work, the pulse repetition-rate effect on femtosecond laser filamentation in air was investigated both numerically and experimentally. The pulse repetition-rate effect has negligible influence at the leading edge of the filament. Clear intensity enhancement from a high-repetition pulse is observed at the peak and tailing edge of the laser filament. As the repetition rate of the laser pulses increases from 100 to 1000 Hz, the length of the filament extends and the intensity inside the filament increases. A physical picture based on the pulse repetition-rate dependent ‘low-density hole’ effect on filamentation is proposed to explain the obtained results well.

Suppressing nonlinear effects in high-power fiber lasers based on fiber gratings has become a hotspot. At present, research is mainly focused on suppressing stimulated Raman scattering in a high-power fiber laser. However, the suppression of spectral broadening, caused by self-phase modulation or four-wave mixing, is still a challenging attribute to the close distance between the broadened laser and signal laser. If using a traditional fiber grating with only one stopband to suppress the spectral broadening, the signal power will be stripped simultaneously. Confronting this challenge, we propose a novel method based on phase-shifted long-period fiber grating (PS-LPFG) to suppress spectral broadening in a high-power fiber master oscillator power amplifier (MOPA) laser system in this paper. A PS-LPFG is designed and fabricated on 10/130 passive fiber utilizing a point-by-point scanning technique. The resonant wavelength of the fabricated PS-LPFG is 1080 nm, the full width at half maximum of the passband is 5.48 nm, and stopband extinction exceeds 90%. To evaluate the performance of the PS-LPFG, the grating is inserted into the seed of a kilowatt-level continuous-wave MOPA system. Experiment results show that the 30 dB linewidth of the output spectrum is narrowed by approximately 37.97%, providing an effective and flexible way for optimizing the output linewidth of high-power fiber MOPA laser systems.