In this paper, a complete wireless power transmission scenario is presented, including an external transmission antenna, an in-body embedded antenna, a rectifying circuit, and a powered sensor. This system operates at the Industrial, Scientific, and Medical bands (902.8–928 MHz). For the antenna design, important parameters including reflection coefficient, radiation pattern, and specific absorption rate are presented. As for the rectifying circuit, a precise model is created utilizing off-the-shelf components. Several circuit models and components are examined in order to obtain optimum results. Finally, this work is evaluated against various sensors' power needs found in literature.

Radiofrequency ablation (RFA) is a non-invasive image-guided procedure where tumors are heated in the body with electrical current. RFA procedures are commonly indicated for patients with limited local disease or who are not surgical candidates. Current methods of RFA use multiple cords and wires that ergonomically complicate the procedure and present the risk of cutting or shorting the circuit if they are damaged. A wireless RFA technique based on electromagnetic induction is presented in this paper. The transmitting and receiving coils were coupled to resonate at the same frequency to ensure the highest power output. The receiving coil was connected to two insulated electrodes on a catheter, which allowed the current to flow to the targeted tissue. The prototype system was tested with ex-vivo bovine tissue, which has similar thermal and electrical properties to human tissue. The setup can monitor the received power, efficiency, temperature, and ablation zone during ablation procedures. The maximum received power was 15 W, and the average maximum efficiency was 63.27%. The novel system was also able to ablate up to a 2 cm ablation zone in non-perfused tissue. This proof of concept for performing RFA wirelessly with electromagnetic induction may merit further optimization.

In this paper, a new design configuration has been proposed in which a prototype of resonant inductive power transfer-based contactless power transfer to wound rotor has been developed which provides field power to brushless alternating current (BLAC) or brushless direct current (BLDC) motors without the use of permanent magnets in the rotor. Further, wound field in the rotor of DC motor can be powered without carbon brushes. The proposed design facilitates motor performance improvement by adding an extra dimension of field flux control, while the armature circuit is conventionally fed from position detection and commutation schemes. It contains a primary multilayer concentrated coil fed with high-frequency resonating AC supply or switched mode supply. A single layer helical secondary coil coaxially fixed on the shaft receives high frequency wireless AC power transmitted from primary coil. Fast rectifier inside the hollow shaft and DC filter provides the transferred DC power to field terminals in the rotor. It has been verified that rotor power can be varied linearly with linear variation in input DC power with the highest efficiency at the resonant frequency. Available power to the rotor remains invariable with rotational speed and angle, which is a necessary requirement for rotor field. DC voltage on the rotor terminals can be effectively controlled during standstill as well as during rotation at any speed.

Aiming at the influence of coupling coefficient variation on the output voltage of a high-power LCC-S topology inductively coupled power transfer (ICPT) system, a synchronous three-phase triple-parallel Buck converter is used as the voltage adjustment unit. The control method for the three-phase current sharing of synchronous three-phase triple-parallel Buck converter and the constant voltage output ICPT system under the coupling coefficient variation is studied. Firstly, the hybrid model consisting of the circuit averaging model of the three-phase triple-parallel Buck converter and the generalized state-space average model for the LCC-S type ICPT system is established. Then, the control methods for three-phase current sharing of the synchronous three-phase triple-parallel Buck converter and constant voltage output of ICPT system are studied to achieve the multi-objective integrated control of the system. Finally, a 3.3 kW wireless charging system platform is built, the experimental results have verified the effectiveness of the proposed modeling and control method, and demonstrated the stability of the ICPT system.

Telemetry acquisition from rodents is important in biomedical research, where rodent behavior data is used to study disease models. Telemetry devices for such data acquisition require a long-term powering method. Wireless power transfer (WPT) via magnetic resonant coupling can provide continuous power to multiple small telemetric devices. Our loosely coupled WPT (LCWPT) system consists of a stationary primary coil and multiple freely moving secondary coils. Our previous LCWPT system was designed to transfer reasonable power to secondary coils at poor orientations but transfers excessively high amounts of power at favorable orientations. Reasonable power is needed for telemetry and radio electronics, but highly induced voltage on the secondary coil creates excess energy which must be dissipated by previous devices, and caused problems (localized heat damage and variations in component properties) leading to drift in operating frequency. To remedy these two problems, a novel scheme is proposed to automatically tune or detune the resonant frequency of the secondary circuit. Our closed-loop controlled tuning or detuning (CTD) approach can be used to prevent excessive power transfer by detuning, or to improve power transfer by tuning, depending on the need. Furthermore, this novel CTD scheme facilitates the use of multiple telemetric devices.

Distribution of wireless power charging field uniformly on a large area pad is critical for power receivers, particularly for wearable devices, wherein small form factor coils are involved. Since the receiver coil size is quite limited in these types of applications, the device is very sensitive to the amount of field it could retain and hence, it needs special placement or snapping mechanism to fix it at an optimum location for reliable wireless charging. In order to overcome this limitation for the end-user, a dual-mode multi-coil power transceiver system is proposed; utilizing resonance filtering to increase the amount of total power delivered with the rather uniform spatial distribution. Two concentric coils; center one driven by 6.78-MHz high-frequency driver (A4WP) and the outer larger one with a 200-KHz low-frequency driver (Qi) with resonant blocker could transfer up to 50 mW standards compliant flat power to a 13-mm radius 30-turns wearable receiver coil everywhere across an 8-cm radius charging pad area without any alignment requirement or snapping. Two different feedback topologies corresponding to each of the H-Bridge power drivers were also presented as an automatic series resonance coil drive frequency lock mechanism, extracting peak powers for each system individually from a standard 5 V-1A USB wall charger.

This paper presents design considerations for an integrated wireless power transfer (WPT) and power line communication (PLC) system (e.g. WPT-PLC). The main goal is to enable wireless charging of mobile electronic products, along with high data rate communication over the shared wireless inductive resonant channel. Starting from a couple of resonant coils, characterized by the S-parameters matrix, the design of an impedance matching network and decoupling filters is carried out to better decouple power and data signals. A pulse-driven class-E power amplifier (PA) and a rectifier are first conceived based on the measured S-parameters and load-pull characterizations. Second, a sine-driven class-E power link, operating at 6.78 MHz, is proposed to reduce the total harmonic distortion of the integrated WPT-PLC system. These design steps aim to ensure high-power efficiency and low harmonic distortion of the class-E PA in order to mildly affect the channel capacity of the PLC. The harmonic interferences of the pulse-driven and sine-driven class-E power links are compared and discussed, together with the electromagnetic compatibility levels, the channel capacity, and the noise disturbances of the PLC channel in order to guarantee an optimized power and data transfer in the integrated WPT-PLC system.

In this paper, we use convex optimization to maximize power efficiency through cascaded multi-coil wireless power transfer systems and investigate the resulting characteristic spacing. We show that although the efficiency is generally a non-convex function of the coil spacing, it can be approximated by a convex function when the effects of higher-order couplings are small. We present a method to optimize the spacing of cascaded coils for maximum efficiency by perturbing the solution of the convex approximation to account for higher-order interactions. The method relies on two consecutive applications of a local optimization algorithm in order to enable fast convergence to the global optimum. We present the optimal configurations of coil systems containing up to 20 identical coils that transfer power over distances up to 4.0 m. We show that when spacing alone is optimized, there exist an optimal number of coils that maximize transfer efficiency across a given distance. We also demonstrate the use of this method in optimizing the placement of a select number of high-Q coils within a system of low-Q relay coils, with the highest efficiencies occurring when the high-Q coils are placed on either side of the largest gaps within the relay coil chain.

Studies on inductive power transfer (IPT) systems are most times either theoretical or experimental. In this paper, we want to bring theoretical models and experimental data together using the impedance based interface proposed in SAE J2954. This proposal characterizes the IPT system by impedances at both coil terminals. We show how the experimental data was retrieved at the interface and use it to validate an analytical model and a Simulink model described within this study. Such models can support the design and development process and therefore a comparison with reality is necessary.

The deployment of multi-insulator tunneling diodes has recently had more attention to be used as rectifiers in energy harvesting rectennas with good potentiality for a millimeter and terahertz range. However, with the rather complicated math to obtain the current–voltage relation, it is difficult to evaluate the design figures of merit (FOM)s such as asymmetry, nonlinearity, responsivity, and dynamic resistance and monitor the impact of changing physical parameters on them. This complicates the decision-making process for the required physical parameters. In this work, a heuristic optimization framework using genetic algorithm is suggested using the transfer matrix method to find the combination of physical parameters which satisfies the minimum required FOM set by users and weighted by their preference.

Typical wireless power transfer (WPT) systems on the market charge only a single receiver at a time. However, it can be expected that the need will arise to charge multiple devices at once by a single transmitter. Unfortunately, adding extra receivers influences the system efficiency. By impedance matching, the loads of the system can be adjusted to maximize the efficiency, regardless of the number of receivers. In this work, we present the analytical solution for achieving maximum system efficiency with any number of receivers for capacitive WPT. Among others, we determine the optimal loads and the maximum system efficiency. We express the efficiency as a function of a single variable, the system kQ-product and demonstrate that load capacitors can be inserted to compensate for any cross-coupling between the receivers.

Wireless power transfer (WPT) has attracted attention from academia and industry in recent years. WPT has natural electrical isolation between primary and secondary side, which ensures safe charging in an underwater environment. This breakthrough technology greatly facilitates the deep-sea power transmission. However, at the current stage the transferred power and energy efficiency level are not up to that of the WPT system in the air. The major concerns include the attenuation is seawater, extreme temperature and pressure conditions, disturbance of ocean currents, and bio-security. Three questions are answered in this paper: first, the expressions of eddy current loss and attenuation of electromagnetic wave in seawater are unified, and the influence of seawater as transmission medium on the WPT system is discussed. Second, the evolution of electromagnetic coupling structure suitable for underwater applications is studied. Third, the loss and heating effects of an underwater WPT system and the corresponding bio-fouling phenomenon are investigated. The questions above were addressed through analysis of electrical properties, coupler structures, and bio-fouling effects of the underwater WPT system. This paper will facilitate the study and research on underwater WPT applications.

In this paper, a concise and universal method to calculate the maximum RF (radio frequency) power transfer efficiency between arbitrary multiple transmitters and multiple receivers wireless power transfer (MIMO-WPT) system is presented. The method is based on maximum Rayleigh quotient which can be deduced either from the multi-port impedance matrix Z or from the multi-port scattering matrix S. Moreover, without any limitation on the transmitting/receiving element's geometry, numbers, operating frequency, coupling method, and so on, the approach is capable to evaluate both the transfer efficiency and the maximum transfer efficiency (MTE) of any type of transmitting and receiving elements, and to obtain the optimum impedances for all transmitting or receiving ports as well. At the end of this paper, the MTEs of some typical MIMO-WPT systems will be calculated to validify the proposed method, and the effectiveness against the receiver's misalignment by using multiple transmitters will be demonstrated.