A simple device was developed for a moisture-proof X-ray diffraction analysis. The device consists of a simple plastic ring where one side was glued on with a thin film to let in the X-ray beam and the other side was covered with grease to seal onto a base plate. This device was later optimized by selecting a good adhesive to glue on the film, a very effective film to minimize the moisture intake, and an optimum ring height to maximize the X-ray intensity. Finally, this simple device was successfully verified that it can protect the anhydrous CaCl2 (hydrophilite) up to 4 days in ambient air.

Synchrotron-based X-ray microbeam measurements were performed on silicon-on-insulator (SOI) features strained by adjacent shallow-trench isolation (STI). Strain engineering in microelectronic technology represents an important aspect of the enhancement in complementary metal-oxide semiconductor device performance. Because of the complexity of the composite geometry associated with microelectronic circuitry, characterization of the strained Si devices at a submicron resolution is necessary to verify the expected strain distributions. The interaction region of the SOI strain extended the SOI film thickness from the STI edge at least 25 times. Regions of 65-nm-thick SOI less than 3 μm wide exhibited an overlap in the strain fields because of the surrounding STI. Microbeam mapping of arrays containing submicron SOI features and embedded STI structures revealed the largest out-of-plane strains because of the close proximity of superimposed strain distributions induced by the STI.

Polycrystalline compounds in the Zn1-xNdxCr2Se4 system were prepared by solid state reaction using selenides (ZnSe, Cr2Se3) and pure elements (Nd, Se) as starting materials. The structural properties were determined by X-ray diffraction and the chemical composition confirmed by SEM-EDX. The observed symmetry is cubic, space group Fd3m, while the lattice parameter varies from 10.4955(7)Å to 10.4976(7)Å, and is larger than for the pure matrix. The solubility limit for the current synthesis route lies below x = 0.1. The magnetic moments, effective and saturation, increase with increasing amount of Nd ions. The Neel temperature TN and ΘCW drop, respectively, to 17.4K and 81K for x = 0.1, independently indicating that neodymium is incorporated into the spinel lattice and promotes antiferromagnetic coupling between the Cr3+ ions.

Powder diffraction data are presented for 3,4-methylenedioxymethylamphetamine hydrochloride monohydrate, the hydrated form of MDMA.HCl, the drug of abuse commonly known as Ecstasy. Samples of pure MDMA.HCl were recrystallized from a variety of solvents, and powder diffraction patterns of the resulting products recorded. Data were collected at room temperature using iron-filtered CoKα radiation.

Advanced courses in Applied Crystallography for Nanosciences are not often delivered in Academia and, consequently, require the organization of events specifically tailored to PhD students, postdocs, and young researchers at the very beginning of their scientific careers.

In an effort to better understand the structural changes occurring during hydrogen loading of erbium target materials, we have performed in situ D2 loading of erbium metal (powder) at temperature (450°C) with simultaneous neutron diffraction analysis. This experiment tracked the conversion of Er metal to the α erbium deuteride (solid-solution) phase and then into the β (fluorite) phase. Complete conversion to ErD2.0 was accomplished at 10 Torr D2 pressure with deuterium fully occupying the tetrahedral sites in the fluorite lattice.

The crystal structure of solifenacin hydrogen succinate [C23H27N2O2(HC4H4O4)] has been solved and refined using synchrotron X-ray powder diffraction data, and optimized using density functional techniques. Solifenacin hydrogen succinate crystallizes in space group P21 (#4) with a = 6.477 03(2), b = 7.830 95(2), c = 23.848 72(7) Å, β = 90.2373(3)°, V = 1209.63(1) Å3, and Z = 2. The hydrogen succinate anions form a chain linked by strong hydrogen bonds parallel to the a-axis. Discrete N–H···O hydrogen bonds lie on the sides of this chain, resulting in a layer parallel to the ab-plane rich in hydrogen bonds. Halfway between these layers the molecules meet in a herringbone packing of aromatic rings. The powder pattern has been submitted to ICDD for inclusion in future releases of the Powder Diffraction File™.

This paper describes a method to determine the equilibrium transformation temperatures in low C steels using the in situ high-temperature X-ray diffraction technique. The samples were heated and then cooled from 1000 to 720 °C in a stepwise manner decreasing to −10 °C. Austenite and ferrite fractions were determined by a quantitative method using the integrated intensities of austenite (111)γ and ferrite (110)α peaks from X-ray diffraction patterns. The effect of the temperature on interplanar d spacings of (111) and (110) crystallographic planes was determined using 2θ maximum positions of the austenite (111)γ and ferrite (110)α peaks. The equilibrium transformation temperatures were determined to be Ae1=720 °C and Ae3=950 °C. The results are in excellent agreement with those obtained by dilatometric analysis and Thermo-Calc phase diagram simulation software. In addition, the results were supported by microstructural observations: the formation of thin ferrite films (5–10 μm) was observed at temperatures near to experimental Ae3.

X-ray powder diffraction data for 3,3-dichloro-1-(4-nitrophenyl)-2-piperidinone, C11H10Cl2N2O3, are reported [a = 11.088(4) Å, b = 11.594(5) Å, c = 12.689(3) Å, α = 118.456(1)°, β = 100.320(3)°, γ = 107.763(3)°, V = 1259.27 Å3, Z = 4 and space group P-1 ]. All measured lines were indexed and are consistent with the P-1 space group. No detectable impurities were observed.

The 2,4-diaryl 1,2,3,4-tetrahydroquinoline derivative (1), described in the title (Chemical formula: C23H22N2O3), was synthesized via the “one-pot” three-component imino Diels–Alder reaction catalyzed by Cu(OTf)2. Molecular characterization was performed by 1H and 13C NMR, Fourier transform-infrared, and gas chromatography-mass spectrometry. The X-ray powder diffraction pattern for the title compound was analyzed and found to be crystallized in an orthorhombic system with space group P212121 (No. 19) and refined unit-cell parameters a = 8.6415(8) Å, b = 12.679(2) Å, c = 17.601(2) Å, and V = 1928.4(2) Å3.

Total Scattering Methods are nowadays widely used for the characterization of defective and nanosized materials. They commonly rely on highly accurate neutron and synchrotron diffraction data collected at dedicated beamlines. Here, we compare the results obtained on conventional laboratory equipment and synchrotron radiation when adopting the Debye Function Analysis method on a simple nanocrystalline material (a synthetic iron oxide with average particle size near to 10 nm). Such comparison, which includes the cubic lattice parameter, the sample stoichiometry and the microstructural (size-distribution) analyses, highlights the limitations, but also some strengthening points, of dealing with conventional powder diffraction data collections on nanocrystalline materials.

As a producer of certified reference materials (CRMs), NIST faces high demand for Standard Reference Materials (SRMs). The demand is exacerbated by widespread misuse of CRMs. When should one use CRMs? When should one not use CRMs? Must labs always use NIST SRMs? How can labs demonstrate analytical capabilities for their accreditation scopes? Why so many questions? Standards developers, laboratory accreditors, and laboratory staff must be able to understand these topics with respect to quality systems in compliance with ISO/IEC 17025. They must calibrate and validate test methods and document traceability to the International System of Units (SI). Many people working in laboratory accreditation and under the umbrella of a quality system do not fully understand what these things are, let alone the language of chemical metrology. On average, they have little training in analytical chemistry, elemental analysis, and reference material development. It is hoped this paper will impress upon the reader the need for understanding how CRMs can be best used in the laboratory. This paper provides a brief background on the above problems and then looks at some of the support and reference information provided by NIST to metals and mining industries labs, commercial CRM producers, and accrediting bodies. The concepts and guidance apply broadly to chemical metrology and fundamental analytical chemistry. The paper includes examples (some from X-ray fluorescence spectrometry) to illustrate concepts.

Biaxial residual stress in a 〈111〉 textured cubic TiN polycrystalline thin film was analyzed by linear least-squares refinement using the method proposed by Yokoyama and Harada [J. Appl. Crystallogr. 42, 185–191 (2009)]. Values of the unstressed (or stress-free) unit-cell parameter a0=4.2332±0.0006 Å and the stress components of σ11=397(88), σ22=401(88), and σ12=−110(100) were obtained. The values of the in-plane stresses σ11 and σ22 presented in the TiN film are practically the same, while σ12 is relatively small. The results obtained in this study confirm that the above theoretical prediction by Yokoyama and Harada can be used to obtain reliable values of stress-free unit-cell parameter and three biaxial stress components of a textured cubic thin film.

To minimize waste, improve process safety, and reduce costs, modifications were implemented to a method for quantifying gallium in plutonium metal using wavelength dispersive X-ray fluorescence. These changes included reducing sample sizes, reducing ion exchange process volumes, using cheaper reagent grade acids, eliminating the use of HF acid, and using more robust containment films for sample analysis. Relative precision and accuracy achieved from analyzing multiple aliquots from a single parent sample were approximately 0.2 and 0.1%, respectively. The same precision was obtained from analyzing a total of four parent materials, and the average relative accuracy from all the samples was 0.4%, which is within programmatic uncertainty requirements.

The crystal structure of danofloxacin mesylate has been solved and refined using synchrotron X-ray powder diffraction data and optimized using density functional theory techniques. Danofloxacin mesylate crystallizes in space group P1 (#1) with a = 6.77474(8), b = 12.4973(4), c = 12.82826(28) Å, α = 84.8709(29), β = 87.7501(10), γ = 74.9916(4)°, V = 1044.723(11) Å3, and Z = 2. The protonation of the danofloxacin cations was established by the analysis of potential intermolecular interactions and differs from that expected from isolated-cation calculations. The crystal structure consists of alternating layers of cations and anions parallel to the ac-plane. There is parallel stacking of the oxoquinoline rings along the a-axis. The expected N–H⋯O hydrogen bonds between the cations and anions are not present. Each cation makes an N–H⋯O hydrogen bond with the other cation, resulting in zig-zag chains along the a-axis. Both cations have strong intramolecular O–H⋯O hydrogen bonds. There are several C–H⋯O hydrogen bonds between the danofloxacin cations and mesylate anions. The powder pattern has been submitted to ICDD® for inclusion in the Powder Diffraction File™ (PDF®).

A set of nine transition metal oxophosphorous compounds, consisting of four hypophosphites and five phosphites has been synthesized and studied using X-ray powder diffraction techniques. The compounds are α-Mn(H2PO2)2·H2O, Co(H2PO2)2 ·0.53H2O, MCl(H2PO2)2·H2O (M = Co2+, Ni2+), M2(HPO3)2·2H2O (M = Co2+, Ni2+), and M11 (HPO3)8(OH)6 (M = Zn2+, Co2+, Ni2+). Unit cells and X-ray powder patterns are reported.

The transition between tetragonal and cubic phases in nanostructured ZrO2-Sc2O3 solid solutions by high-temperature X-ray powder diffraction using synchrotron radiation is presented. ZrO2-8 and 11 mol% Sc2O3 nanopowders that exhibit the t′- and t″-forms of the tetragonal phase, respectively, were synthesized by a stoichiometric nitrate-lysine gel-combustion route. The average crystallite size treated at 900°C was about 25 nm for both compositions. Our results showed that t′-t″ and t″-cubic transitions take place for the 8 and 11 mol% Sc2O3 samples, respectively.