Millimeter-wave reconfigurable bandpass filters with the ability to operate between 60 GHz and the E-band, capable of providing good channel isolation, are presented. A fully integrated filter with all reconfigurable elements embedded for compactness and a switchable filter that uses radio frequency micro-electro-mechanical system (RF MEMS) single-pole double-throw switches are designed. A new method that increases fractional bandwidths is introduced. It uses inductively coupled inverters without requiring their tuning. New circuit models are offered for inverters, reconfigurable resonators, and reconfigurable bandstop stubs. Our compact bandpass filter achieved a footprint of only 4.75 mm × 3.75 mm. Measurements for our filters show good agreement with the results of simulations.

The safe operating area (SOA) of InGaP/GaAs heterojunction bipolar transistors has been studied using two-dimensional Technology Computer-Aided Design (TCAD) tool. Comprehensive physical models, including hydrodynamic transport-based impact ionization and self-heating models were implemented. The simulations for two DC modes (constant Ib and Vb modes) captured all the SOA features observed in measurements and some failure mechanisms were revealed for the first time by TCAD simulations. The simulated results are also in agreement with analytical modeling. The simulation not only gives us insight to the detailed failure mechanisms, but also provides guidance for the design of devices with better ruggedness and improved SOA performances.

In this paper, a compact multiple-input multiple-output (MIMO) antenna system with high isolation is proposed for 2.4 GHz wireless local area network (WLAN) application. The system is composed of two aperture-coupled shorted patch antennas with a spacing of 4 mm (only 0.032λ). The antenna is fed with an H-shaped coupling slot, and the defected shorting wall is used for high isolation. The proposed MIMO system exhibits an isolation of better than −20 dB and a maximum isolation of −43 dB at the central frequency. The envelope correlation coefficient is less than 0.01. The simulated and measured results show that the proposed antenna is a good candidate for MIMO system with higher isolation and better diversity.

In this work, the design, fabrication, and testing of low sidelobe level (SLL) Butler matrix-based beamformers is presented. The paper is divided in two parts. The first part deals with the conventional technique of simultaneous excitation of input ports. The second part introduces some novel modified low SLL Butler matrices, as an alternative advantageous design choice. Circuit architecture makes use of asymmetric branch line couplers able to provide high values of output power division ratios. Radiation patterns with SLLs far lower than −23 dB are achieved, without the use of any additional circuitry, in opposition to the case of simultaneous port excitation. Apart from SLL reduction, the switched line-phase shifter technique is applied in order to increase the number of radiated beams and improve scanning coverage. The beamformers are suitable for interference suppressing point-to-multipoint ground communications, satellite and radar/EW/SIGINT systems. Several microstrip circuit prototypes are designed, fabricated, and tested, whereas extended simulation and measurements results are adduced.

In this paper, a novel and compact center-fed dual-band WiFi printed antenna is presented. This antenna is designed using two different arms which correspond to the oscillation points of the dual band, and uses parasitic capacitance and U-shaped microstrip line to match and control the necessary bandwidth. The measured frequency bandwidth of this antenna is 2.3–2.61 GHz (310 MHz, 12.7%) at 2 GHz, and the high-frequency bandwidth is 4.82–5.84 GHz (1020 MHz, 19.1%) at 5 GHz, which meets the requirements for applications in global WiFi communication. This PCB antenna is double-sided, long, and narrow; its size is 7 × 45.9 × 1 mm3; it can be applied to wireless access point; and it has a near-omni-directional radiation pattern. The design, analysis, and measured results of this proposed antenna will be presented.

A SPICE model of an antenna for transmitting is proposed. This model allows for the calculation of the frequency-domain radiation fields for a range of frequencies in which the model is valid, it also allows for the direct calculation of the time-domain (TD) radiation fields for an arbitrary TD excitation signal, the spectrum of which should be within the modeling range. The model is then verified by two examples, both of them demonstrate its validity. This model can be a part of a complete system-level model for electromagnetic compatibility simulation.

In this paper, the design of thinned planar antenna arrays of isotropic radiators with optimum side lobe level reduction is studied. The teaching–learning-based optimization (TLBO) method, a newly proposed global evolutionary optimization method, is used to determine an optimum set of turned-ON elements of thinned planar antenna arrays that provides a radiation pattern with optimum side lobe level reduction. The TLBO represents a new algorithm for optimization problems in antenna arrays design. It is shown that the TLBO provides results that are better than (or the same as) those obtained using other evolutionary algorithms.

This research work presents a microstrip-fed antenna that is small, low-profile, planar, and suitable for WLAN/WiMAX and partially ultra-wideband (UWB) applications. The radiating element of the proposed antenna consists of rectangular-shaped ring embedded with a three inverted “S”-shaped and inverted “C”-shaped strips. This antenna is capable of generating penta bands having good impedance matching with wideband characteristics. Prototype of the proposed antenna has been designed, simulated, fabricated, and tested. The overall small size of the antenna is 24.75 mm × 27.39 mm × 1.6 mm with volumetric size of 1 cm3. To understand the characteristics of the proposed antenna, the parametric studies are being performed. The return loss of the proposed antenna shows fair agreement with the simulated and measured results.

A new compact quad-passband bandpass filter (BPF) using multi-mode resonators (MMRs) based on multi-layered substrate technique is proposed. The filter consists of a pair of multi-mode resonators (uniform impedance resonator and stepped impedance resonator) operated at 1.8/3.7 GHz on top layer and the other pair of the multi-mode resonators operated at 2.4/3 GHz on bottom layer. Source–load coupling lines are used to be the input/output (I/O) ports for providing the multi-paths propagations by cross-coupling effects in the filter. Specifically, the operated frequencies of the filter at 1.8/2.4/3/3.7 GHz with bandwidths of 6.7, 8.2, 4.6, and 7.2% are successfully designed and implemented. The proposed filter is useful for the multi-passband filters design, especially when the passbands are needed to be very close.

This paper presents an original characterization method of trapping phenomena in gallium nitride high electron mobility transistors (GaN HEMTs). This method is based on the frequency dispersion of the output-admittance that is characterized by low-frequency S-parameter measurements. As microwave performances of GaN HEMTs are significantly affected by trapping effects, trap characterization is essential for this power technology. The proposed measurement setup and the trap characterization method allow us to determine the activation energy Ea and the capture cross-section σn of the identified traps. Three original characterizations are presented here to investigate the particular effects of bias, ageing, and light, respectively. These measurements are illustrated through different technologies such as AlGaN/GaN and InAlN/GaN HEMTs with non-intentionally doped or carbon doped GaN buffer layers. The extracted trap signatures are intended to provide an efficient feedback to the technology developments

This work demonstrates design methods that can achieve remarkable enhancement in the stopband response of microstrip coupled-line filters. The frequencies of resonance and/or the transmission zeros of a coupled-line section can be controlled by its length. Therefore, by constructing a filter with coupled lines of incommensurate lengths such that these frequencies do not overlap, substantial improvement in the stopband response can be obtained. Besides its compact structure and simple design procedure, an unprecedented performance is demonstrated experimentally in which the transmission level is maintained below −20 dB up to as high as 11.9 f0 for a third-order filter, where f0 is the center frequency.

This paper presents a comparison between three evolutionary algorithms (EAs) for pattern synthesis of offset reflector antenna fed by a planar array of horn antennas. To perform the optimization process, an elliptical-shaped beam in the U–V plane (U = sinθ cosφ and V = sinθ sinφ) is considered as the desired far-field radiation pattern. To attain the appropriate excitation value for array elements, three conditions are considered: (1) variable amplitude (with uniform phase distribution), (2) variable phase (with uniform amplitude distribution), and (3) variable amplitude and phase excitation. Obtaining the appropriate excitation value based on the mathematical methods is always complicated and time-consuming. Therefore, genetic algorithm (GA) and particle swarm optimization (PSO) as two well-known EAs have been used widely for different applications and shown the promise to solve complicated problems. This paper compares these two EAs with invasive weed optimization (IWO) which is robust and has simple and powerful process with few tuning parameters. We found that for pattern synthesis of multi-feed reflector antenna in different conditions, IWO can provide accurate and comparable results with GA and PSO methods at approximately same iteration number. The convergence diagrams as well as the optimized radiation patterns for different conditions are presented and compared for GA, PSO and IWO.

This paper presents results of direction of arrival (DOA) estimation using multiple signal classification (MUSIC), Root-MUSIC, and estimation of signal parameters via rotational invariance technique algorithms. As is well known, these algorithms are mainly based on the specific properties of the signal covariance matrix as well as the decomposition of the observation space into two subspaces, one for the signal and the other for the noise. Here, we are particularly interested in the quality of sources localization considering only the case of uncorrelated radio frequency signals impinging on an antenna array. A measurement system consisting of a linear array antenna and a five-port network applicable to a demodulator such as a receiver is used for the DOA estimation process. Co-simulations performed with the Advanced Device System and Matlab yielded interesting results not only on their performance but also on their limitation.

A design of annular ring microstrip antenna with finite ground structure is proposed in this paper. The proposed geometry offers impedance bandwidth of 2.362 GHz and has stable radiation patterns for all resonant frequencies in the operational band. It is also found that shape and dimension of the finite ground plane is a key factor in improving the bandwidth of the proposed geometry. The geometry is low profile and has simple structure, therefore can be used for lower band of ultra-wideband applications.

In this paper, the design and test of a single-chip RF pulse-width modulator and driver (PWMD) aimed at exciting a high-power class-E GaN high-power stage at 435 MHz is described. For the required buffer size, avoiding potential ringing of the pulses within the buffer structure presents a major challenge in the design process. Therefore, a smaller test chip capable of driving capacitive loads of up to 5 pF was initially designed, fabricated, and tested. An approach based on three-dimensional electromagnetic simulations was used to validate the test results and offers excellent simulation accuracy. Based on the results obtained for test chip an enlarged PWMD chip capable of driving a 40 W high-power stage has been designed and tested on passive loads representing the targeted final stage.

In this paper, we show a second-order (four-resonator) absorptive bandstop filter circuit topology which gives a larger bandwidth compared to a first-order topology. Due to the absorptive characteristic, it creates a large attenuation at the center frequency using low-Q resonators. Since low-Q resonators can be used in generating a large attenuation, small-size resonators can be employed in bandstop filter design. Analytic design equations are provided so that a higher-order absorptive bandstop filter can be designed analytically. It is also shown that the second-order filter topology exhibits a better frequency selectivity having a same bandwidth. The proposed filter topology has been applied to a design of a miniaturized low-temperature co-fired ceramic bandstop filter with low-Q resonators. The Q-factor of the lumped-element resonators has been chosen to be 5 for demonstration.

In this paper, the analysis and simulation of a novel geometrical structure of the frequency selective surface (FSS), which has been achieved through the conductive loading of the simple circular ring with wedge-shaped metal vanes has been discussed. The electrical performance and behavior of the proposed structure have been studied in Ku band (12–18 GHz) of the electromagnetic spectrum for satellite communication. We have radially optimized the proposed structure to enhance the performance, such as reflection and transmission bandwidth. We have also discussed the effect of incident electric field at 0°, 10°, 30°, and 50° on the electrical performance of the proposed FSS. In addition to this, the effect of angular sensitivity on the proposed structure through increasing the number of conductive loaded wedge-shaped metal vanes is also explored. However, the structural parameters of the proposed FSS have been obtained through the synthesis technique. The analytical results obtained from the synthesis technique have been supported by the simulation results achieved through CST Microwave Studio as well as Ansoft high frequency structural simulator (HFSS), which are commercially available simulators based on the finite integral and finite-element technique, respectively. Furthermore, for validation of the numerical results, the Ansoft circuit simulator which is based on mixed potential integral equations (MPIE) and solved by the method-of-moment has also been used to obtain the reflection and transmission parameters through the values of inductance and capacitance, which have been achieved by the numerical analysis.

The front-end circuitry of transceiver modules is slowly being updated from GaAs-based monolithic microwave integrated circuits (MMICs) to Gallium-Nitride (GaN). Especially GaN power amplifiers and T/R switches, but also low-noise amplifiers (LNAs), offer significant performance improvement over GaAs components. Therefore it is interesting to also explore the possible advantages of a GaN mixer to enable a fully GaN-based front-end. In this paper, the design-experiment and measurement results of a double-balanced image-reject mixer MMIC in 0.25 μm AlGaN/GaN technology are presented. First an introduction is given on the selection and dimensioning of the mixer core, in relation to the linearity and conversion loss. At the intermediate frequency (IF)-side of the mixer, an active balun has been used to compensate partly for the loss of the mixer. An on-chip local-oscillator (LO) signal amplifier has been incorporated so that the mixer can function with 0 dBm LO input power. After the discussion of the circuit design the measurement results are presented. The performance of the mixer core and passive elements has been demonstrated by measurements on a test-structure. The mixer MMIC measured conversion loss is <8 dB from 6 to 12 GHz, at 1 GHz IF and 0 dBm LO power. The measured image rejection is better than 30 dB.

A compact slot antenna for high-gain ultra wideband applications is presented. The slot is asymmetrically cut in the ground plane and is a combination of two rectangles. A hexagonal patch with two stepped coplanar waveguide-feed is used to excite the slot. The capacitive reactance of the hexagonal patch is neutralized by the inductive reactance created by the asymmetric slot and results into wider impedance matching. The measured impedance bandwidth of the proposed antenna is 11.85 GHz (2.9–14.75 GHz). The radiation patterns of the proposed antenna are found to be omni-directional in the H-plane and bi-directional in the E-plane. To enhance the gain of the antenna, a compact three-layer frequency selective surface (FSS) is used as a reflector. The overall thickness of the FSS is 3.5 mm. There is 4–5 dBi improvement in antenna gain after application of the FSS. The measured and simulated results are in good agreement.

A low specific absorption rate (SAR) reconfigurable multiband coplanar waveguide fed planar inverted-F antenna (PIFA) is presented in this paper. Different numbers of meander-turn-shaped slots are etched on the PIFA radiating plate to excite new resonant frequencies. Extra resonant frequencies are created by increasing the number of meander-turn-shaped slots for different wireless communication applications. A new independent resonant frequency is created by etching a coupled slot within the ground plane for the upper WLAN. A PIN diode switch is used to reconfigure the fundamental resonant frequency from the LTE band 11 to band 8 with a total of 63% size reduction compared with the original PIFA size. Furthermore, the SAR in the human head is investigated using the Hugo voxel model in CST Microwave Studio. The volume of the antenna is 22 × 30 mm2 over a 35 × 50 mm2 ground plane, which is suitable for handheld devices.