Resorcinol/formaldehyde (RF) foam resin is an attractive material as a low-density target in high-power laser–plasma experiments because of its fine network structure, transparency in the visible region, and low-Z element (hydrogen, carbon, and oxygen) composition. In this study, we developed disk-shaped RF foam and deuterated RF foam targets with 40–200 μm thickness and approximately 100 mg/cm3 density having a network structure from 100 nm to a few micrometers cell size. By deuteration, the polymerization rate was drastically slowed down owing to kinetic isotope effects. These targets were used in high-power laser experiments where a megaelectronvolt proton beam was successfully generated.

A high-energy picosecond 355 nm ultraviolet (UV) laser operating at 100 Hz was demonstrated. A 352 mJ, 69 ps, 1064 nm laser at 100 Hz was realized firstly by cascaded regenerative, laser diode end-pumped single-pass and side-pumped main amplifiers. The stimulated Raman scattering-based beam shaping technique, thermally induced birefringence compensation and 4f spatial filter-image relaying systems were used to maintain a relatively homogeneous beam intensity distribution during the amplification process. By using lithium triborate crystals for second- and third-harmonic generation (THG), a 172 mJ, approximately 56 ps, 355 nm UV laser was achieved with a THG conversion efficiency of 49%. To the best of our knowledge, it is the highest pulse energy of a picosecond 355 nm UV laser so far. The beam quality factor ${M}^2$ and pulse energy stability were ${M}_x^2$=3.92, ${M}_y^2$=3.71 and root mean square of 1.48%@3 hours. This laser system could play significant roles in applications including photoconductive switch excitation, laser drilling and laser micro-fabrication.

We report on an improved ytterbium-doped yttrium aluminum garnet thin-disk multi-pass amplifier for kilowatt-level ultrafast lasers, showcasing excellent beam quality. At a repetition rate of 800 kHz, the 6.8 ps, 276 W seed laser is amplified up to an average power of 1075 W, corresponding to a pulse energy of 1.34 mJ. The 36-pass amplifier is designed as a compact mirror array in which the beam alternately propagates between the mirrors and the disk by a quasi-collimated state. We adopted a quasi-collimated propagation to confine stray and diffracted light by the slight curvature of the disk, which enables us to achieve an outstanding extraction efficiency of up to 57% with excellent beam quality in stable laser operation at high power. The beam quality at 1075 W was measured to be M2 < 1.51. Furthermore, stability testing was demonstrated with a root-mean-square power fluctuation of less than 1.67% for 10 min.

With ultrafast laser systems reaching presently 10 PW peak power or operating at high repetition rates, research towards ensuring the long-term, trouble-free performance of all laser-exposed optical components is critical. Our work is focused on providing insight into the optical material behavior at fluences below the standardized laser-induced damage threshold (LIDT) value by implementing a simultaneous dual analysis of surface emitted particles using a Langmuir probe (LP) and the target current (TC). ${\mathrm{HfO}}_2$ and ${\mathrm{ZrO}}_2$ thin films deposited on fused silica substrates by pulsed laser deposition at various ${\mathrm{O}}_2$ pressures for defect and stoichiometry control were irradiated by Gaussian, ultrashort laser pulses (800 nm, 10 Hz, 70 fs) in a wide range of fluences. Both TC and LP collected signals were in good agreement with the existing theoretical description of laser–matter interaction at an ultrashort time scale. Our approach for an in situ LIDT monitoring system provides measurable signals for below-threshold irradiation conditions that indicate the endurance limit of the optical surfaces in the single-shot energy scanning mode. The LIDT value extracted from the LP-TC system is in line with the multipulse statistical analysis done with ISO 21254-2:2011(E). The implementation of the LP and TC as on-shot diagnostic tools for optical components will have a significant impact on the reliability of next-generation ultrafast and high-power laser systems.

Using two infrared pulsed lasers systems, a picosecond solid-state Nd:YAG laser with tuneable repetition rate (400 kHz–1 MHz) working in the burst mode of a multi-pulse train and a femtosecond Ti:sapphire laser amplifier with tuneable pulse duration in the range of tens of femtoseconds up to tens of picoseconds, working in single-shot mode (TEWALASS facility from CETAL-NILPRP), we have investigated the optimal laser parameters for kinetic energy transfer to a titanium target for laser-thrust applications. In the single-pulse regime, we controlled the power density by changing both the duration and pulse energy. In the multi-pulse regime, the train’s number of pulses (burst length) and the pulse energy variation were investigated. Heat propagation and photon reflection-based models were used to simulate the obtained experimental results. In the single-pulse regime, optimal kinetic energy transfer was obtained for power densities of about 500 times the ablation threshold corresponding to the specific laser pulse duration. In multi-pulse regimes, the optimal number of pulses per train increases with the train frequency and decreases with the pulse power density. An ideal energy transfer efficiency resulting from our experiments and simulations is close to about 0.0015%.

A band-stop angular filter (BSF) based on hump volume Bragg gratings (HVBGs) is proposed. Band-stop filtering in a two-stage amplifier laser system is discussed and simulated. Simulation results show that small-scale self-focusing effects in the laser system can be effectively suppressed with the BSF due to the control of fast nonlinear growth in a specific range of spatial frequencies in the laser beam. Near-field modulation of the output beam from the laser system was decreased from 2.69 to 1.37 by controlling the fast nonlinear growth of spatial frequencies ranging from $0.6~\text{mm}^{-1}$ to $1.2~\text{mm}^{-1}$ with the BSF. In addition, the BSF can be used in a plug-and-play scheme and has potential applications in high-power laser systems.

The Centre for Advanced Laser Applications in Garching, Germany, is home to the ATLAS-3000 multi-petawatt laser, dedicated to research on laser particle acceleration and its applications. A control system based on Tango Controls is implemented for both the laser and four experimental areas. The device server approach features high modularity, which, in addition to the hardware control, enables a quick extension of the system and allows for automated data acquisition of the laser parameters and experimental data for each laser shot. In this paper we present an overview of our implementation of the control system, as well as our advances in terms of experimental operation, online supervision and data processing. We also give an outlook on advanced experimental supervision and online data evaluation – where the data can be processed in a pipeline – which is being developed on the basis of this infrastructure.

A type of $\unicode[STIX]{x1D706}/4$–$\unicode[STIX]{x1D706}/4$ ultra-broadband antireflective coating has been developed using modified low refractive silica and high refractive silica layers by a sol–gel dip coating method for amplifier blast shields of the Shen Guang II high power laser facility (SG-II facility). Deposition of the first layer (high refractive index silica) involves baking at $200\,^{\circ }\text{C}$ in the post-treatment step. The second layer (low refractive index, $n=1.20$) uses low refractive index silica sol modified by acid catalysis. Thermal baking at temperatures no less than $500\,^{\circ }\text{C}$ for 60 min offers chemical stability, ethanol scratch resistance, and resistance to washing with water. The average residual reflection of dual-side-coated fused silica glass was less than 1% in the spectral range from 450 to 950 nm. Transmission gain has been evaluated by taking into account angular light, and the results show that the transmission gain increases with increasing light incidence. Even at $60^{\circ }$, the transmission spectrum of the broadband antireflective coating effectively covered the main absorption peak of Nd:glass.

We demonstrate the generation, spectral broadening and post-compression of second harmonic pulses using a thin beta barium borate (BBO) crystal on a fused-silica substrate as the nonlinear interaction medium. By combining second harmonic generation in the BBO crystal with self-phase modulation in the fused-silica substrate, we efficiently generate millijoule-level broadband violet pulses from a single optical component. The second harmonic spectrum covers a range from long wave ultraviolet (down to 310 nm) to visible (up to 550 nm) with a bandwidth of 65 nm. Subsequently, we compress the second harmonic beam to a duration of 4.8 fs with a pulse energy of 0.64 mJ (5 fs with a pulse energy of 1.05 mJ) using chirped mirrors. The all-solid free-space apparatus is compact, robust and pulse energy scalable, making it highly advantageous for generating intense second harmonic pulses from near-infrared femtosecond lasers in the sub-5 fs regime.

The driving mechanism of solar flares and coronal mass ejections is a topic of ongoing debate, apart from the consensus that magnetic reconnection plays a key role during the impulsive process. While present solar research mostly depends on observations and theoretical models, laboratory experiments based on high-energy density facilities provide the third method for quantitatively comparing astrophysical observations and models with data achieved in experimental settings. In this article, we show laboratory modeling of solar flares and coronal mass ejections by constructing the magnetic reconnection system with two mutually approaching laser-produced plasmas circumfused of self-generated megagauss magnetic fields. Due to the Euler similarity between the laboratory and solar plasma systems, the present experiments demonstrate the morphological reproduction of flares and coronal mass ejections in solar observations in a scaled sense, and confirm the theory and model predictions about the current-sheet-born anomalous plasmoid as the initial stage of coronal mass ejections, and the behavior of moving-away plasmoid stretching the primary reconnected field lines into a secondary current sheet conjoined with two bright ridges identified as solar flares.

We experimentally investigate the generation of above-threshold harmonics completely from argon atoms on an excited state using mid-infrared femtosecond laser pulses. The highly nonlinear dependences of the observed signal on the pulse energy and polarization of the probe laser pulses indicate its nonperturbative characteristic.

A diode-pumped master oscillator power amplifier system based on a cryogenic Yb:YAG active-mirror laser has been developed. The performances of the laser amplifier at low temperature and room temperature have been investigated theoretically and experimentally. A maximum output energy of 3.05 J with an optical-to-optical efficiency of 14.7% has been achieved by using the master amplifier system.

Based on the pulse-shaping unit in the front end of high-power laser facilities, we propose a new hybrid scheme in a closed-loop control system including wavelet threshold denoising for pretreatment and a first derivative adaptive smoothing filter for smooth pulse recovery, so as to effectively restrain the influence of electrical noise and FM-to-AM modulation in the time–power curve, and enhance the calibration accuracy of the pulse shape in the feedback control system. The related simulation and experiment results show that the proposed scheme can obtain a better shaping effect on the high-contrast temporal shape in comparison with the cumulative average algorithm and orthogonal matching pursuit algorithm combined with a traditional smoothing filter. The implementation of the hybrid scheme mechanism increased the signal-to-noise ratio of the laser pulse from about 11 dB to 30 dB, and the filtered pulse is smooth without modulation, with smoothness of about 98.8%.

Here we report on a simple-to-implement and cost-effective approach for laser pulse contrast enhancement, based on the ${\chi}^{(3)}$ nonlinear self-focusing effect. An intentionally induced and gently controlled self-focusing in a thin glass transforms the time-dependent intensity into variation in beam divergence. Followed by a spatial discriminating filter, only the strongly focused fraction traverses the setup, at the expense of efficiency. A numerical model, accounting for the pulse and material parameters via a Gaussian ABCD matrix, provides an estimate for the instantaneous beam waist and transmission efficiency, which enables us to evaluate the resulting contrast enhancement. The estimated contrast enhancement spans between 0.5 and 2.5 orders of magnitude, in conjunction with approximately 25%–90% estimated efficiency, depending on the pulse parameters. In a preliminary experiment we demonstrated the effect with 10s-μJ sub GW regime with approximately 40$\%$ efficiency and a contrast improvement of more than or equal to 20 dB.

To meet the demands of laser-ion acceleration at a high repetition rate, we have developed a comprehensive diagnostic system for real-time and in situ monitoring of liquid sheet targets (LSTs). The spatially resolved rapid characterizations of an LST’s thickness, flatness, tilt angle and position are fulfilled by different subsystems with high accuracy. With the help of the diagnostic system, we reveal the dependence of thickness distribution on collision parameters and report the 238-nm liquid sheet generated by the collision of two liquid jets. Control methods for the flatness and tilt angle of LSTs have also been provided, which are essential for applications of laser-driven ion acceleration and others.

Laser target components consist of multicomponent porous and nonporous materials that are adhesively bonded together. In order to assess the extent and quantity of adhesive wicking into porous foam, micro X-ray computed tomography (CT) and image processing software have been utilized. Two different laser target configurations have been assessed in situ and volume rendered images of the distribution and quantities of adhesive have been determined for each.

The damage characteristics of fused silica were investigated under low-temporal coherence light (LTCL). It was found that the laser-induced damage threshold (LIDT) of fused silica for the LTCL was lower than that of the single longitudinal mode pulse laser, and for the LTCLs, the LIDTs decrease with the increasing of laser bandwidth, which is not consistent with the temporal spike intensity. This is due to the nonlinear self-focusing effect and multi-pulse accumulation effect. The specific reasons were analyzed based on theoretical simulation and experimental study. This research work is helpful and of great significance for the construction of high-power LTCL devices.

High-gain harmonic generation (HGHG) is effective to produce fully coherent free-electron laser (FEL) pulses for various scientific applications. Due to the limitation of seed lasers, HGHG typically operates at a low repetition rate. In this paper, a harmonic-enhanced HGHG scheme is proposed to relax the peak power requirement for the seed laser, which can therefore operate at megahertz and a higher repetition rate. Moreover, the setup of the scheme is compact and can be adopted in an existing single-stage HGHG facility to extend the shortest achievable wavelength. Simulations show that FEL emission at 13.5 nm (20th harmonic) can be obtained with a 270 nm, 1 MW (peak power) seed laser.

A novel method, combining an asymmetric four-grating compressor (AFGC) with pulse post-compression, is numerically demonstrated to improve the spatial uniformity of laser beams and hence to suppress small-scale self-focusing (SSSF) during the beam propagation in nonlinear materials of high peak power lasers. The spatial uniformity of laser beams is an important factor in performing post-compression, due to the spatial intensity modulation, or hot spots will be aggravated during the nonlinear propagation and then seriously damage the subsequent optical components. Three-dimensional numerical simulations of post-compression are implemented based on a femtosecond laser with a standard compressor and an AFGC, respectively. The simulated results indicate that post-compression with the AFGC can efficiently suppress the SSSF and also shorten the laser pulses from 30 fs to sub-10 fs. This work can provide a promising route to overcome the challenge of SSSF and will be meaningful to promote the practical application of the post-compression technique in high peak power lasers.

This paper systematically investigated the impact mechanisms of proton irradiation, atomic oxygen irradiation and space debris collision, both individually and in combination, on the laser damage threshold and damage evolution characteristics of HfO2/SiO2 triple-band high-reflection films and fused silica substrates using a simulated near-Earth space radiation experimental system. For the high-reflection film samples, the damage thresholds decreased by 15.38%, 13.12% and 46.80% after proton, atomic oxygen and simulated space debris (penetration) irradiation, respectively. The coupling irradiation of the first two factors resulted in a decrease of 26.93%, while the combined effect of all the three factors led to a reduction of 63.19%. Similarly, the fused silica substrates exhibited the same pattern of laser damage performance degradation. Notably, the study employed high-precision fixed-point in situ measurement techniques to track in detail the microstructural changes, surface roughness and optical-thermal absorption intensity before and after proton and atomic oxygen irradiation at the same location, thus providing a more accurate and comprehensive analysis of the damage mechanisms. In addition, simulations were conducted to quantitatively analyze the transmission trajectories and concentration distribution lines of protons and atomic oxygen incident at specific angles into the target material. The research findings contribute to elucidating the laser damage performance degradation mechanism of transmissive elements in near-Earth space environments and provide technical support for the development of high-damage-threshold optical components resistant to space radiation.