The maximisation of control power is considered for an aircraft with multiple control surfaces, with the force and moment coefficients specified by polynomials of the control surface deflections of degree two. The optimal deflections, which maximise and minimise any force or moment coefficient, are determined subject to constraints on the range of deflection of each control surface. The results are applied to a flying wing configuration to determine: (i/ii) the pitch trim, at the lowest drag for the fastest climb, and at the highest drag for the steepest descent; (iii) the maximum and minimum pitching moment; (iv) the maximum and minimum yaw control power and the fraction needed to compensate an outboard engine failure for several propulsion configurations; (v) the maximum and minimum rolling moment. The optimal use of all control surfaces has significant advantages over using just one, e.g. the range of drag modulation with pitch trim is much wider and the maximum and minimum available control moments larger.

Multicriteria trajectory optimisation is expected to increase aviation safety, efficiency and environmental compatibility, although neither the theoretical calculation of such optimised trajectories nor their implementation into today’s already safe and efficient air traffic flow management reaches a satisfying level of fidelity. The calibration of the underlying objective functions leading to the virtually best available solution is complicated and hard to identify, since the participating stakeholders are very competitive. Furthermore, operational uncertainties hamper the robust identification of an optimised trajectory. These uncertainties may arise from severe weather conditions or operational changes in the airport management. In this study, the impact of multicriteria optimised free route trajectories on the air traffic flow management is analysed and compared with a validated reference scenario which consists of real flown trajectories during a peak hour of Europe’s complete air traffic in the upper airspace. Therefore, the TOolchain for Multicriteria Aircraft Trajectory Optimisation (TOMATO) is used for both the multicriteria optimisation of txrajectories and the calculation of the reference scenario. First, this paper gives evidence for the validity of the simulation environment TOMATO, by comparison of the integrated reference results with those of the commercial fast-time air traffic optimiser (AirTOp). Second, TOMATO is used for the multicriteria trajectory optimisation, the assessment of the trajectories and the calculation of their integrated impact on the air traffic flow management, which in turn is compared with the reference scenario. Thereby, significant differences between the reference scenario and the optimised scenario can be identified, especially considering the taskload due to frequent altitude changes and rescinded constraints given by waypoints in the reference scenario. The latter and the strong impact of wind direction and wind speed cause wide differences in the patterns of the lateral trajectories in the airspace with significant influence on the airspace capacity and controller’s taskload. With this study, the possibility of a successful 4D free route implementation into Europe’s upper airspace is proven even over central Europe during peak hours, when capacity constraints are already reaching their limits.

The aviation industry relies on accurate models. These models are used to predict an aircraft system’s outputs, and thus allow an understanding of the parameters involved, which could lead to system improvements. This study focuses on the engine modelling of an aircraft, and on its experimental validation using the Cessna Citation X Research Aircraft Simulator designed by CAE Inc., equipped with a level D Flight Dynamics toolbox. Level D is the highest rank attributed by the Federal Aviation Administration FAA certification authorities for flight dynamics. The proposed model aims to predict the thrust and the fuel consumption for various altitudes, Mach numbers and throttle lever angles (TLA). Different generic static models, which correspond to their steady state, from the literature, were used in this study; however, most of them were validated under restricted hypotheses. An optimisation algorithm was used in order to tune the static model parameters with the set of identification flight test data. Another set of data was then used in order to validate the identified model. Furthermore, a dynamic model corresponding to the transient operations was identified. TLA steps, impulses and ramp perturbations were performed in order to identify the system response, and to validate system dynamic model with other flight tests than the identification tests.

High-speed aircraft often develop separation-induced leading-edge vortices and vortex flow aerodynamics. In this paper, the discovery of separation-induced vortex flows and the development of methods to predict these flows for wing aerodynamics are reviewed. Much of the content for this article was presented at the 2017 Lanchester Lecture and the content was selected with a view towards Lanchester’s approach to research and development.

In this paper, we examine some of the physics behind Vertical Take-Off and Landing (VTOL) flying machines, and some of the emerging technologies that are driving the recent upsurge of new VTOL projects. The paper attempts to put these into context by examining some of the projects that have been publicised over the past couple of years, particularly those that transition from hovering into wing-borne flight. Although much progress has been made, there still needs to be significant breakthroughs in technologies, particularly battery technology, before the dream of fast, quiet and environmentally friendly inter-city VTOL aircraft can be realised.

The focus of this paper is on the modelling of miniature electromechanical actuators used in a morphing wing application, on the development of a control concept for these actuators, and on the experimental validation of the designed control system integrated in the morphing wing-tip model for a real aircraft. The assembled actuator includes as its main component a brushless direct current motor coupled to a trapezoidal screw by using a gearing system. A Linear Variable Differential Transformer (LVDT) is attached on each actuator giving back the actuator position in millimetres for the control system, while an encoder placed inside the motor provides the position of the motor shaft. Two actuation lines, each with two actuators, are integrated inside the wing model to change its shape. For the experimental model, a full-scaled portion of an aircraft wing tip is used with the chord length of 1.5 meters and equipped on the upper surface with a flexible skin made of composite fibre materials. A controllable voltage provided by a power amplifier is used to drive the actuator system. In this way, three control loops are designed and implemented, one to control the torque and the other two to control the position in a parallel architecture. The parallel position control loops use feedback signals from different sources. For the first position control loop, the feedback signal is provided by the integrated encoder, while for the second one, the feedback signal comes from the LVDT. For the experimental model, the parameters for the torque control, but also for the position control-based encoder signal, are implemented in the power amplifier energising the electrical motor. On the other hand, a National Instruments real-time system is used to implement and test the position control-based LVDT signal. The experimental validation of the developed control system is realised in two independent steps: bench testing with no airflow and wind-tunnel testing. The pressure data provided by a number of Kulite sensors equipping the flexible skin upper surface and the infrared thermography camera visualisations are used to estimate the laminar-to-turbulent transition point position.

The Surface Operations Simulator and Scheduler (SOSS) is a fast-time simulation of the airport surface used to rapidly develop and test new surface scheduling concepts. Gate conflicts present a challenge for surface scheduling. A late departure pushback or early arrival sharing the same gate can cause a gate conflict, which if left unmanaged, can lead to surface gridlock. Surface scheduling concepts that meter departures at their gates can increase the likelihood of gate conflicts. In real operations, hardstand areas are used to temporality park aircraft out of the way to avoid gate conflicts. New SOSS models and functionality for hardstand operations were developed to simulate gate conflict management approaches using hardstands to temporarily park either the arrival or departure out of the way of the other. Four gate conflict management approaches were simulated with surface scheduling and their effects on surface operations were compared. The four gate conflict management approaches each allowed a unique subset of resolution actions including early departure pushback, sending the departure to the hardstand, and sending the arrival to the hardstand. The gate conflict management approaches allowing arrivals to be sent to the hardstand were found to be most successful in resolving the gate conflicts and maintaining scheduler performance measured by takeoff time predictability.

Route planning and airspace sectorisation are two central tasks in air traffic management. Traditionally, the routing and sectorisation problems were considered separately, with aircraft trajectories serving as input to the sectorisation problem and, reciprocally, sectors being part of the input to the path finding algorithms.

In this paper we propose a simultaneous design of routes and sectors for a transition airspace. We compare two approaches for this integrated design: one based on mixed integer programming, and one Voronoi-based model that separates potential “hotspots” of controller activity resulting from the terminal routes.

We apply our two approaches to the design of Stockholm Terminal Maneuvering Area.

This paper presents an open framework, through which, conventional general purpose aerial munitions can be converted into smart munitions. The retrofit consists of a smart adaptation kit (SAK) having a dedicated Guidance and Control Module (GCM). The adaptation kit along with the GCM ensures that the SAK glide optimally towards the designated target. To reduce cost, the number of control surfaces of the SAK has been kept to a bare minimum, which resulted in an under actuated system. The methodology proposed utilises the theory of gain-scheduled control and leads to an efficient procedure for the design of the controllers, which accurately track reference trajectories defined in an inertial reference frame. The paper illustrates the application of this procedure to the design of stabilisation and tracking controller for the SAK. The design phase is summarised, and the performance of the resulting controllers is assessed in simulation using dynamic model of the vehicle. Simulation results show that apart from improved circular error probable (CEP) of hitting the target, munition ballistic range has also significantly increased with the proposed modification.

The takeoff-mass of a two-stage-to-orbit Rocket-Based Combined Cycle Engine-Rocket (RBCC-RKT) launch vehicle is a crucial factor in its comprehensive performance. This paper optimizes the takeoff-mass together with the trajectory by reformulating it to a nonlinear optimal control problem. The range of the second stage rocket mass is considered as a process constraint. When the scopes of initial and terminal states are specified, the problem can be solved by using the Gauss pseudo-spectral method (GPM). In order to reduce the convergent difficulty caused by using table data, the data in different stages are utilized by employing an integrated interpolation strategy through the optimization. Simulation results show that the mass can be effectively optimized to meet the inertia mass ratio constraint of the first-stage, and the separation of Mach number and altitude can be optimized at the same time.

The combustion instability characteristics in a model dump combustor with an exhaust nozzle were experimentally investigated. The first objective was to understand the effects of operating conditions and geometric conditions on combustion instability. The second objective was to examine more generalised parameters that affect the onset of combustion instability. Three different premixed gases consisting of air and hydrocarbon fuels (C2H4, C2H6, C3H8) were burnt in the dump combustor at various inlet velocity, equivalence ratio and combustion chamber length. Dynamic pressure transducer and photomultiplier tube with a bandpass filter were used to measure pressure fluctuation and CH* chemiluminescence data. Peak frequencies and their maximum power spectral densities of pressure fluctuations at same equivalence ratios showed different trends for each fuel. However, the dynamic combustion characteristics of pressure fluctuations displayed consistent results under similar characteristics chemistry times regardless of the used hydrocarbon fuels. The results showed that characteristic chemistry time and characteristic convection time influenced combustion instabilities. It was found that the convective-acoustic combustion instability could be prevented by increasing the characteristic chemistry time and characteristic convection time.

Numerical simulations have been carried out for a 32.16-ft-diameter rotor in autorotational forward flight. Coupled flapping and rotational equations were solved using the transient simulation method (TSM) to ascertain the quasistatic torque equilibrium conditions. The Pitt/Peters inflow theory was adopted in the simulations, and an airfoil look-up table made by a compressible Navier-Stokes solver was used. The adverse cyclic and collective pitch inputs were introduced in a similar fashion to helicopter control in that the cyclic lever is pulled back and the collective lever is pushed down for increasing airspeeds. The simulation results showed that the longitudinal cyclic pitch input combined with a lowered collective pitch increases the rotating torque for a low shaft angle and an advance ratio greater than one, producing both high lift and a high lift-to-drag ratio. Upon introducing the adverse cyclic and collective pitch inputs, the control range broadened, and a torque equilibrium condition was detected at 414.7kt (700ft/s) of airspeed in the simulation.

This paper investigates the potential of a lever-type pitch trimmer to cause an overstress in light and microlight aeroplanes. It concludes that this potential exists and could potentially cause a catastrophic structural failure – with the evidence from one reported fatal accident suggesting that this may have already happened. However, it is shown that this need not be the case, with restricted nose-up control authority, high manoeuvre stability and the use of a trim wheel (as opposed to a lever) with a restrictive rate of control input shown as three methods, most likely in combination, by which this potential can be removed. Suggestions are made for airworthiness standard wording which might be used to ensure adequate safety of future aircraft designs.

The model of Nano quad-rotors contains many uncertainties such as an external disturbance from a wind field, highly non-linear strong coupling between variables and body measurement errors. To deal with these uncertainties and control the Nano quad-rotors, a novel data-based disturbance observer (DO) is firstly proposed to observe disturbances from a wind field and perturbations from errors of parameter estimation. Then the DO is used to improve the conventional dynamic inversion (DI) method to obtain an enhanced dynamic inversion (EDI) method, which relies only on roughly estimated geometrical parameters, thus eliminating the largest flaw of conventional DI, namely depending on detailed plant information. Simulation results show that the method proposed achieved good trajectory tracking with only roughly estimated geometrical values under wind field; the DO proposed can accurately estimate disturbance from a wind field and perturbation from error of parameter estimation.

This paper deals with the problem of fault-tolerant control (FTC) for redundant multirotor unmanned aerial vehicles (UAVs) subject to actuators failures. A fuzzy logic approach is used to solve the constrained control allocation problem by adjusting the components of the multiplexing vector once a motor failure is detected. This fuzzy logic allocation problem is tuned using the Bacterial Foraging Algorithm (BFA), a powerful bio-inspired optimisation technique. The effectiveness of this approach is illustrated through real experimental application to a hexarotor UAV, where up to two motors failures are considered.

One of the main challenges of future aircraft engines is to achieve low pollutant emissions while maintaining high combustion efficiencies and operability. The Flameless Combustion (FC) regime is pointed as one of the promising solutions due to its well-distributed reaction zones that yield low NOx emissions and oscillations. A dual-combustor configuration potentially facilitates the attainment of FC in the Inter-Turbine Burner (ITB). The development of such burner is dependent on knowledge regarding NOx formation and the parameters affecting it. It is known from the literature that the NOx formation mechanisms are different in FC. Therefore, in an attempt to clarify some of the mechanisms involved in NOx formation at relevant conditions, a chemical reactor network model developed to represent the ITB is explored. The role of prompt NOx was previously shown to be dominant at relatively low inlet temperatures and atmospheric pressure. In order to check these findings, five chemical reaction mechanisms were employed. All of them overpredicted NOx emissions and the overprediction is likely to be caused by the prompt NOx subset implemented in these mechanisms. Higher reactants temperatures and operational pressures were also investigated. Overall NOx emissions increased with temperature and the NOx peak moved to lower equivalence ratios. Operational pressure changed the emissions trend with global equivalence ratio. Leaner conditions had behaviour similar to that of conventional combustors (increase in NOx), while NOx dropped with further increase in equivalence ratio due to suppression of the prompt NOx production, as well as an increase in NO reburning. These trends highlight the differences between the emission behaviour of the ITB with those of a conventional combustion system.

Integrated Modular Avionics enables applications of different criticality levels to share the same hardware platform with an established temporal and spatial isolation. On-chip communication systems for such platforms must support different bandwidth and latency requirements of applications while preserving time predictability. In this paper, our concern is a time-predictable on-chip network architecture for targeting applications in mixed-criticality aerospace systems. The proposed architecture introduces a mixed, priority-based and time-division-multiplexed arbitration scheme to accommodate different bandwidth and latency in the same network while preserving worst-case time predictability for end-to-end communication without packet loss. Furthermore, as isolation of erroneous transmission by a faulty application is a key aspect of contingency management, the communication system should support isolation mechanisms to prevent interference. For this reason, a sampling port and isolated sampling buffer-based approach is proposed with a transmission authorisation control mechanism, guaranteeing spatial and temporal isolation between communicating systems.

This paper presents the results of a research performed at the Research Laboratory in Active Controls, Avionics and Aeroservoelasticty (LARCASE), at ÉTS, concerning optimisation strategies for cruise flight segments with imposed flight time (delimited by waypoints with required time of arrival constraints). Specifically, a new algorithm is presented that identifies the optimal vertical navigation profile (flight altitude and speed optimisation) for a cruise segment with imposed lateral navigation profile, bounded by two waypoints with required time of arrival constraints. The set of evaluated vertical navigation profiles are characterised by identical altitudes and speeds at their initial and final waypoints (at the beginning and the end of the cruise segment under optimisation), a maximum of one altitude step (relative to the initial altitude), and are flown at constant speed. This study investigates the flight performance increase (total cost reduction) for a flight along the optimal vertical navigation profile, relative to a flight at the optimal speed and initial cruise altitude. The evaluation was performed using a medium haul transport aircraft flight performance model, for three lateral navigation profiles and three wind profiles. The algorithm is targeted for Flight Management Systems platforms, to provide the optimal flight trajectory for the imposed lateral flight profile and time constraints.