The high fission yield and long half life of cesium and strontium make them the two most high-risk products from nuclear fission, so their separation from radioactive wastes is an important step in mitigating their harmful effects. Clinoptilolite, because of its thermal stability, high radiation resistance, and selectivity, was considered as the adsorbent for this purpose. In order to then separate the adsorbent-adsorbate complex from aqueous solution, the clinoptilolite was prepared as a magnetized composite with nanomagnetite. This magnetically modified zeolite enabled the efficient and quick separation of the adsorbent from solution using magnetic separation. The ability of this composite to remove Cs+ and Sr2+ from aqueous solutions was assessed and characterized using X-ray diffraction, X-ray fluorescence, Fourier-transform infrared spectroscopy, differential thermogravimetric analysis, and vibrating-sample magnetometry. Variables such as initial ion concentration, pH, contact time, and temperature in the sorption process were studied and optimized. The maximum adsorption capacities of the composite were 188.7 and 36.63 mg g-1 for Cs+ and Sr2+, respectively. Investigation of the kinetics revealed that the adsorption process onto the composite was quicker than in the case of the zeolite alone. The equilibrium data were analyzed using the Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models. The mean free energy of sorption (E) for both ions was in the range 8–16 kJ mol-1, confirming that an ion-exchange mechanism had occurred. Positive ΔH° and negative ΔG° values were indicative of the endothermic and spontaneous nature of the removal of Cs+ and Sr2+. The saturation magnetization of the composite was measured (17.46 Am2/kg), implying fast magnetic separation of the sample after adsorption. The results obtained revealed that the natural Iranian zeolite nanomagnetite composite was a good ion exchanger in the removal of Cs+ and Sr2+.

The effects of chemical treatment on the radiation-shielding properties of Philippine natural zeolites were investigated using EpiXS following the EPICS2017 library. The zeolites were studied using X-ray diffraction and energy-dispersive X-ray spectroscopy. The acid treatment eliminated Fe and Ca, having a negative impact on the cross-section of the HCl-modified zeolite. The mass attenuation coefficients of the raw, NaOH- and HCl-modified zeolites at 1332 keV were 0.0545, 0.0544 and 0.0548 cm2 g–1, respectively. At 100–10,000 keV, the linear attenuation coefficient depends on the density and increases in the order HCl-modified > NaOH-modified > raw zeolite. In the energy range of 100–16,000 keV, the mean free path and half-value layer values are in the order of HCl-modified < NaOH-modified < raw zeolite. The raw and NaOH-modified zeolites have comparable effective atomic numbers, whereas the HCl-treated zeolite has significantly lower such values.

Natural zeolite (clinoptilolite)-based geopolymers were synthesized using alkali aluminate solution, including aluminate anodizing waste solution. The effect of calcination of the clinoptilolite sample at 900°C was investigated. The samples were studied by powder X-ray diffraction, thermal analysis, scanning electron microscopy and N2-specific surface area. The alkali aluminate-activated clinoptilolite geopolymers are characterized by satisfactory compressive strength (up to 37 MPa), low density and acceptable shrinkage. The clinoptilolite geopolymer obtained contains an X-ray amorphous phase and newly formed phillipsite and zeolite NaP. The presence of zeolite phases in the geopolymer agglomerate could be beneficial in products with specific qualities and properties, such as ion exchange, passive cooling, antimicrobial activity, etc.

This work examines a tuff from the Tinebdar deposit located in Sidi Aich (east Algeria) for possible use as an alternative material for the adsorption of Asucryl red (a textile dye). Natural tuff represents an economic and environmentally friendly alternative compared to synthetic zeolites. The starting materials were characterized by means of powder X-ray diffraction, Brunauer–Emmett–Teller-specific surface area and pore diameter analysis. Batch experiments were performed and various parameters that have an effect on the adsorption process (i.e. pH, clay amount, contact time and initial concentration) were investigated. The <125 μm grain-size fraction of the tuff contains 45 wt.% mordenite. The adsorption equilibrium was established in 10 min and the adsorption kinetics were better described by the second-order kinetic model. The adsorption isotherm of the results obtained fits better to the Langmuir and Timkin models. The adsorption capacity qt varies from 60 to 70 mg g–1 with temperature increasing from 293 to 333 K. The thermodynamic nature of the adsorption process was determined by calculating ΔH°, ΔS° and ΔG° values. The positive value for ΔH° confirms that the adsorption is endothermic.

Natural zeolitic tuff from Brus (Serbia) consisting mostly of clinoptilolite (about 90%) has been investigated for the reduction of the Mg concentration in spring water. The sorption capacity of the zeolite is relatively low (about 2.5 mg Mg g-1 for the initial concentration of 100 mg Mg dm-3). The zeolitic tuff removes Mg from water solutions by ion exchange, which has been demonstrated by energy dispersive X-ray analysis (EDS). The extent of ion exchange was influenced by the pH and the initial Mg concentration. Kinetic studies revealed that Lagergen's pseudo-second order model was followed. Intra-particle diffusion of Mg2+ influenced the ion exchange, but it is not the rate-limiting step. Rather than having to dispose of the Mg-loaded (waste) zeolite, a possible application was tested. Addition to a wastewater with a low concentration of Mg showed that it could successfully make up for the lack of Mg micronutrient and, accordingly, enabled the growth of phosphate-accumulating bacteria A. Junii, increasing the amount of phosphate removed from the wastewater.

Rheological, porosimetric, and SEM studies of cements with additions of natural zeolites (chabazite, mordenite and clinoptilolite) were investigated. The addition of 5% zeolite to cement pastes had a plastifying effect. The increase in the rheological parameters of aqueous cement–zeolite suspensions began after additions of more than 10% zeolite. At a water/solid ratio (w/s) = 0.5 all compositions exhibited similar rheological behaviour for yield stress and maximum shear stress values. At lower w/s values the rheology depended on the zeolite used, decreasing in the order Sl (clinoptilolite, Nižny Hrabovec deposit, Slovakia), M (mordenite, Philipines), Bp (clinoptilolite, Beli Plast deposit, Bulgaria), NM (clinoptilolite, Saint Cloud deposit, New Mexico) and Ch (chabazite, Nasm Yan deposit, Korea).

After 28 days of hydration the mixtures containing 10% Bp clinoptilolite, mordenite, and Sl clinoptilolite (up to 30%) had unchanged specific pore volumes but additions of 10% and 30% of chabazite and NM clinoptilolite and of 30% mordenite and Bp clinoptilolite lead to increases in the total specific pore volume compared to the neat cement paste. Between the 28th and 180th days of hydration the specific volume of the pores in all the cement-zeolite pastes decreased due to the filling of the pores with products from the pozzolanic reaction between the zeolites and the hydration products of the cement.

The pozzolanic reaction between zeolite and the hydration products of cement is enhanced by the zeolite content in the samples and depends on the Si/Al ratio (clinoptilolite (Si/Al >4.5), mordenite (Si/Al >5), chabazite (Si/Al <2.5)) and the surface area (clinoptilolite from Slovakia has the smallest crystallites and, hence, the greatest reactive surface area).

The work reported herein involves the characterization of natural zeolites from two different mines (San Andrés and Tasajeras; Cuba) using XRD, SEM, TG-DTA, ICP and surface area measurements. In addition, the chemical composition of zeolites, the heavy metal and environmental organic toxins content, the ion exchange rates, stability under biological conditions using simulated body fluids as well as the binding capacity for histamine have been investigated with a view to using them as medical products. The investigated zeolites contain clinoptilolite and mordenite as major phases. Furthermore, the samples are apparently free from fibrous materials according to SEM observations. In particular, the San Andrés zeolite binds remarkable amounts of histamine which are nearly irreversible under acidic (pH = 1; 12.4 mg/g) and neutral conditions (pH = 7; 15.7 mg/g), respectively. Thus, the San Andrés sample may well be applied as a medical product due to its excellent binding capacity for histamine along with its remaining optimum physico-chemical characteristics.

Non-isothermal dehydration kinetics of a heulandite-type zeolite-rich tuff from Turkey was investigated using thermogravimetric data recorded at three different heating rates (5, 10 and 20°C/min) under nitrogen flow. Isoconversional model-free methods gave a constant activation energy over the temperature range 30–200°C suggesting that the dehydration is a single-step process within this temperature range. The apparent activation energy was determined as: 34.54±1.18, 30.99±1.14 and 27.79±1.42 kJ/mol by the Flynn–Wall–Ozawa, the Kissinger–Akahira–Sunose and the Friedman methods, respectively. The activation energy values determined were less than the activation energy for vaporization of bulk water, indicating control of the dehydration rate by diffusion of water within this temperature range.

A new protocol for the quantitative determination of zeolite-group mineral compositions by electron probe microanalysis (wavelength-dispersive spectrometry) under ambient conditions, is presented. The method overcomes the most serious challenges for this mineral group, including new confidence in the fundamentally important Si-Al ratio. Development tests were undertaken on a set of natural zeolite candidate reference samples, representing the compositional extremes of Na, K, Cs, Mg, Ca, Sr and Ba zeolites, to demonstrate and assess the extent of beam interaction effects on each oxide component for each mineral. These tests highlight the variability and impact of component mobility due to beam interaction, and show that it can be minimized with recommended operating conditions of 15 kV, 2 nA, a defocused, 20 μm spot size, and element prioritizing with the spectrometer configuration. The protocol represents a pragmatic solution that works, but provides scope for additional optimization where required. Vital to the determination of high-quality results is the attention to careful preparations and the employment of strict criteria for data reduction and quality control, including the monitoring and removal of non-zeolitic contaminants from the data (mainly Fe and clay phases). Essential quality criteria include the zeolite-specific parameters of R value (Si/(Si + Al + Fe3+), the 'E%' charge-balance calculation, and the weight percent of non-hydrous total oxides. When these criteria are applied in conjunction with the recommended analytical operating conditions, excellent inter-batch reproducibility is demonstrated. Application of the method to zeolites with complex solid-solution compositions is effective, enabling more precise geochemical discrimination for occurrence-composition studies. Phase validation for the reference set was conducted satisfactorily with the use of X-ray diffraction and laser-ablation inductively-coupled plasma mass spectroscopy.

The removal of lead and zinc from a binary solution by fixed bed depths (40, 80 and 120 mm) of a natural zeolite was examined at a flow rate of 1 mL/min. The results obtained were fitted to the Bed Depth Service Time (BDST) model and the parameters of the model (q and k) were used to design a column system for flow rates of 2 and 3 mL/min at a bed depth of 80 mm. The experimental results were in excellent agreement with those predicted and experimental breakthrough curves for the binary systems were obtained. This approach facilitates the design of effective binary column processes without additional experimentation. Two major design parameters, the Empty Bed Contact Time (EBCT) and the zeolite usage rate, were calculated. The highest EBCT value of 13.56 min represents the optimal conditions for the binary (Pb+Zn) solution.

Industrial minerals, particularly bentonites, have long been used in treatments to improve the stability and shelf life of white wines. We evaluated a new combination of rocks and minerals, including steam-treated bentonites and natural zeolites (chabazite and phillipsite), to greatly reduce the risk of protein and tartaric instability of wines. Detailed mineralogical, chemical and electrokinetic studies of these materials were conducted using powder X-ray diffraction (PXRD), X-ray fluorescence (XRF), microporosimetry, BET surface-area analysis and zeta-potential measurements. Several model wine solutions containing Bovine Serum Albumin (BSA) were prepared to evaluate the oenological performance of the rock/mineral combinations. UV-VIS spectrophotometry and ion chromatography were used to evaluate the degree of wine stabilization from the protein and tartaric point of view.

The experimental results showed that steam treatment modifies both the microporosity and external surface area of the bentonite. These changes in surface area, along with creation of hydrophobic surfaces, significantly modified the behaviour of the steam-treated bentonites, requiring an increase in the amount of material necessary to bring the protein content to required levels. An important benefit derived from the use of steam-treated bentonites is that the pre-mixing with water before addition to wine is not necessary, as the material is readily dispersed. Finally, the addition of natural zeolites effectively decreased the potassium content, thereby improving the tartaric stability of white wines. In addition, this procedure results in minimal waste, as the bentonite-zeolite mixture can be reused as soil amendments in agriculture.