This paper provides a summary of recent research connected with the shock ignition (SI) concept of the inertial confinement fusion which was carried out at PALS. In the experiments, Cu planar targets coated with a thin CH layer were used. Two-beam irradiation experiment was applied to investigate the effect of preliminary produced plasma to shock-wave generation. The 1ω or 3ω main beam with a high intensity >1015 W/cm2 generates shock wave, while the other 1ω beam with the intensity below 1014 W/cm2 creates CH pre-plasma simulating the pre-compressed plasma related to SI. Influence of laser wavelength on absorbed energy transfer to shock wave was studied by means of femtosecond interferometry and measuring the crater volume. To characterize the hot electron and ion emission, two-dimensional (2D) Kα-imaging of Cu plasma and grid collector measurements were used. In single 1ω beam experiments energy transport by fast electrons produced by resonant absorption made a significant contribution to shock-wave pressure. However, two-beam experiments with 1ω main beam show that the pre-plasma is strongly degrading the scalelength which leads to decreasing the fast electron energy contribution to shock pressure. In both the single 3ω beam experiments and the two-beam experiments with the 3ω main beam, do not show any clear influence of fast electron transport on shock-wave pressure. The non-monotonic behavior of the scalelength at changing the laser beam focal radius in both presence and absence of pre-plasma reflects the competition of plasma motion and electron heat conduction under the conditions of one-dimensional and 2D plasma expansion at large and small focal radii, respectively.

The paper is a continuation of research carried out at Prague Asterix Laser System (PALS) related to the shock ignition (SI) approach in inertial fusion, which was carried out with use of 1ω main laser beam as the main beam generating a shock wave. Two-layer targets were used, consisting of Cu massive planar target coated with a thin polyethylene layer, which, in the case of two-beam irradiation geometry, simulate conditions related to the SI scenario. The investigations presented in this paper are related to the use of 3ω to create ablation pressure for high-power shock wave generation. The interferometric studies of the ablative plasma expansion, complemented by measurements of crater volumes and Kα emission, clearly demonstrate the effect of changing the incident laser intensity due to changing the focal radius on efficiency of laser energy transfer to a shock wave and fast electron emission. The efficiency of the energy transfer increases with the radius of the focused laser beam. The pre-plasma does not significantly change the character of this effect. However, it unambiguously results in the increasing temperature of fast electrons, the total energy of which remains very small (<0.1% of the laser energy). This study shows that the optimal radius from the point of view of 3ω radiation energy transfer to the shock wave is the maximal one used in these experiments and equal to 200 µm that corresponds to the minimal effect of two-dimensional (2D)-expansion. Such a result is typical for the ablation process determined by electron conductivity energy transfer under the conditions of one-dimensional or 2D matter expansion without any appreciable effect due to energy transfer by fast electrons. The 2D simulations based on application of the ALANT-HE code and an analytical model that includes generation and transport of hot electrons has been used to support of experimental data.

This paper reports on properties of a plasma formed by sequential action of two laser beams on a flat target, simulating the conditions of shock-ignited inertial confinement fusion target exposure. The experiments were performed using planar targets consisting of a massive copper (Cu) plate coated with a thin plastic (CH) layer, which was irradiated by the 1ω PALS laser beam (λ = 1.315 μm) at the energy of 250 J. The intensity of the fixed-energy laser beam was scaled by varying the focal spot radius. To imitate shock ignition conditions, the lower-intensity auxiliary 1ω beam created CH-pre-plasma which was irradiated by the main beam with a delay of 1.2 ns, thus generating a shock wave in the massive part of the target. To study the parameters of the plasma treated by the two-beam irradiation of the targets, a set of various diagnostics was applied, namely: (i) Two-channel polaro-interferometric system irradiated by the femtosecond laser (~40 fs), (ii) spectroscopic measurements in the X-ray range, (iii) two-dimensional (2D)-resolved imaging of the Kα line emission from Cu, (iv) measurements of the ion emission by means of ion collectors, and (v) measurements of the volume of craters produced in a massive target providing information on the efficiency of the laser energy transfer to the shock wave. The 2D numerical simulations have been used to support the interpretation of experimental data. The general conclusion is that the fraction of the main laser beam energy deposited into the massive copper at two-beam irradiation decreases in comparison with the case of pre-plasma. The reason is that the pre-formed and expanding plasma deteriorates the efficiency of the energy transfer from the main laser pulse to a solid part of the targets by means of the fast electrons and the wave of an electron thermal conductivity.

The paper is directed to the study of high-temperature plasma and ablation plasma formation as well as efficiency of the laser energy transfer to solid targets irradiated by laser pulses with intensities of 1–50 PW/cm2 and duration of 200–300 ps, i.e., at conditions corresponding to the characteristics of the laser spike designed to generate the igniting shock wave in the shock ignition concept. The experiments have been performed at Prague Asterix Laser System. The iodine laser delivered 250 ps (full width at half maximum) pulses with the energy in the range of 100–600 J at the first (λ1 = 1.315 µm) and third (λ3 = 0.438 µm) harmonic frequencies. The focal spot radius of the laser beam on the surface of Al or Cu targets made was gradually decreased from 160 to 40 µm. The diagnostic data collected using three-frame interferometry, X-ray spectroscopy, and crater replica technique were interpreted by two-dimensional numerical and analytical modeling which included generation and transport of fast electrons. The coupling parameter Iλ2 was varied in the range of 1 × 1014−8 × 1016 Wμm2/cm2 covering the regimes of weak to intense fast electron generation. The dominant contribution of fast electron energy transfer into the ablation process and shock wave generation was found when using the first harmonic laser radiation, the focal spot radius of 40–100 µm, and the laser energy of 300–600 J.

300 keV electron beams with energy peaked in the range 280–390 keV were generated by focusing a high contrast ratio but temporally double pulsed 800 nm ultrafast laser onto a flowing water jet under both helium atmosphere at ambient pressure and water aspirator vacuum conditions, using laser intensities in the range 1015–1018 Wcm−2. Their characteristics have been investigated as functions of inter-pulse delay, incidence geometry and laser pulse chirp. Shot-to-shot variation of the beams' equatorial and azimuthal distributions was also recorded in real time. Measurements of the emitted charge and energy have been performed. Secondary X-ray emission arising from impingement of the electron beams on the target chamber walls and other parts of the apparatus have been identified. Preliminary results after transition to a high repetition rate laser system have shown similar behavior. Approaches for improvements and applications are suggested.

The paper is devoted to the study of plasma effects, which are present in laser ablation at relatively high intensity (I ≥ 1012 W/cm2). We start from the classical “two temperature model” of laser ablation (“cold solid approximation”) and we extend it to higher intensities where laser-induced heating and laser-induced changes in the background material become relevant. The new model is also compared to experimental results on laser ablation of solid targets from short pulse lasers at high intensities (up to 1014 W/cm2). Finally, we consider the effects on laser-ablation of laser-generated fast electrons.

Fast electrons are effectively generated from solid targets of cone-geometry by irradiating intense laser pulses, which is applied to fast ignition scheme. For realizing optimal core heating by those electrons, understanding the characteristics of electrons emitted from cone targets is crucial. In this paper, in order to understand the generation and transport processes of hot electrons inside the cone target, two-dimensional (2D) particle-in-cell (PIC) simulations were carried out. It is shown that hot electrons form current layers which are guided by self-generated surface magnetic field, which results in effective energy transfer from laser pulse to hot electrons. When the hot electrons propagate through the steep density gradient at the cone tip, electrostatic field is induced via Weibel instability. As a result, hot electrons are confined inside and emitted gradually from the target, as an electron beam of long duration. Energy spectrum and temporal profile of hot electrons are also evaluated at the rear side of the target, where the profile of rear side plasma is taken from the fluid code and the result is sent to Fokker-Planck code.

The properties of an electron beam (e-beam) formed in air under atmospheric pressure are reported. The nanosecond generators RADAN-303 (two devices) and RADAN-220, producing nanosecond voltage pulses with amplitude of up to 400 kV and subnanosecond rise time were used in the experiments. It was shown for the first time that the duration of e-beam current of gas diode behind the foil does not exceed 0.1 ns. The maximum amplitude of current of a supershort avalanche electron beam (SAEB) behind the foil was ∼400 A. The data on the influence of various parameters on e-beam current amplitude measured behind the foil were obtained. An electron beam with energy less than 60 keV and powerful X-ray radiation were formed in discharge gap simultaneously with SAEB.

The emission of high-energy protons in laser–solid interactions and the theories that have been used to explain it are briefly reviewed. To these theories we add a further possibility: the acceleration of protons inside the target by the electric field generated by fast electrons. This is considered using a simple one-dimensional model. It is found that for relativistic laser intensities and sufficiently long pulse durations, the proton energy gain is typically several times the fast electron temperature. The results are very similar to those obtained for proton acceleration by electron expansion into vacuum.

The paper reviews and analyses the experiments devoted to the propagation in dense matter of fast electrons produced in the interaction of short-pulse ultra-high-intensity laser pulses with solid density targets.