Hostname: page-component-78c5997874-94fs2 Total loading time: 0 Render date: 2024-11-08T08:27:12.422Z Has data issue: false hasContentIssue false
  • English
  • Français

Mechanical Properties of Wear Tested LIGA Nickel

Published online by Cambridge University Press:  01 February 2011

N. R. Moody ,
J. M. Jungk ,
M. S. Kennedy ,
S. V. Prasad ,
D. F. Bahr  and
W. W. Gerberich
N. R. Moody
Affiliation:
Sandia National laboratories, Livermore, CA 94550
J. M. Jungk
Affiliation:
University of Minnesota, Minneapolis, MN 55455
M. S. Kennedy
Affiliation:
Washington State University, Pullman, WA 99164
S. V. Prasad
Affiliation:
Sandia National Laboratories, Albuquerque, NM 87158
D. F. Bahr
Affiliation:
Washington State University, Pullman, WA 99164
W. W. Gerberich
Affiliation:
University of Minnesota, Minneapolis, MN 55455
Get access

Abstract

Strength, friction, and wear are dominant factors in the performance and reliability of materials and devices fabricated using nickel based LIGA and silicon based MEMS technologies. However, the effects of frictional contacts and wear on the mechanical performance of microdevices are not well-defined. To address these effects on performance of LIGA nickel, we have begun a program employing nanoscratch and nanoindentation. Nanoscratch techniques were used to generate wear patterns using loads of 100, 200, 500, and 990 μN with each load applied for 1, 2, 5, and 10 passes. Nanoindentation was then used to measure properties in each wear pattern correcting for surface roughness. The results showed a systematic increase in hardness with applied load and number of nanoscratch passes. The results also showed that the work hardening coefficient determined from indentation tests within wear patterns follows the work hardening behavior established from tensile tests, supporting use of a nanomechanics-based approach for studying mechanical properties of wear tested material.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 841: Symposium R – Fundamentals of Nanoindentation and Nanotribology III , 2004 , R7.8
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Prasad, S.V., Michael, J.R., Christenson, T.R., Scripta Materialia 48, 255–260 (2003).Google Scholar
2. Allameh, S. M., Lou, J., Kavishe, F., Buchheit, T., Soboyejo, W. O., Mater, Sci. Engng A 371, 256–266 (2004).Google Scholar
3. Bobji, M. S., Biswas, S. K., J. Mater. Res. 14, 2259–2268 (1999).Google Scholar
4. Joslin, D. L., Oliver, W. C., J. Mater. Res. 5, 123–126 (1990).Google Scholar
5. Page, T. F., Pharr, G. M., Hay, J. C., Oliver, W. C., Lucas, B. N., Herbert, E., Riester, L., in Fundamentals of Nanoindentation and Nanotribology, edited by Moody, N. R., Gerberich, W. W., Baker, S. P., Burnham, N. (MRS Symp. Proc., 522, Pittsburgh, PA 1998) pp. 53–64.Google Scholar
6. Gerberich, W. W., Tymiak, N. I., Kramer, D. E., Daugela, A., Jungk, J., Li, M., Phil. Mag. A 82, 3349–3360 (2002).Google Scholar
7. Harvey, S., Huang, H., Venkataraman, S., Gerberich, W. W., J. Mater. Res. 8 1291–1299 (1993).Google Scholar