Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-12-01T02:14:28.413Z Has data issue: false hasContentIssue false
  • English
  • Français

Conductive Electrospun and Micro-StereoLithographically Produced Porous Scaffolds as Potential Neural Interface Materials

Published online by Cambridge University Press:  20 January 2012

Shawn M. Dirk ,
Kirsten N. Cicotte ,
Elizabeth L. Hedberg-Dirk ,
Stephen Buerger ,
Patrick P. Lin  and
Gregory Reece
Shawn M. Dirk
Affiliation:
Organic Materials Department, Sandia National Laboratories, Albuquerque, NM 87185, U.S.A.
Kirsten N. Cicotte
Affiliation:
Organic Materials Department, Sandia National Laboratories, Albuquerque, NM 87185, U.S.A. Center for Biomedical Engineering, University of New Mexico, Albuquerque, New Mexico, U.S.A.
Elizabeth L. Hedberg-Dirk
Affiliation:
Center for Biomedical Engineering, University of New Mexico, Albuquerque, New Mexico, U.S.A. Chemical and Nuclear Engineering Department, University of New Mexico, Albuquerque, New Mexico, U.S.A.
Stephen Buerger
Affiliation:
Intelligent System Controls Department, Sandia National Laboratories, Albuquerque, New Mexico, U.S.A.
Patrick P. Lin
Affiliation:
Department of Orthopedic Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas U.S.A.
Gregory Reece
Affiliation:
Department of Plastic Surgery, The University of Texas MD Anderson Cancer Center, Houston, Texas, U.S.A.
Get access

Abstract

Our overall intent is to develop improved electrically active prosthetic devices to allow interactions between regenerated nerve fibers (axons) and external electronics. To allow for infiltration of axons, these devices must be highly porous. Additionally, they must exhibit selective and structured conductivity to allow the connection of electrode sites with external circuitry with tunable electrical properties that enable the transmission of neural signals through physical connections to external circuitry (e.g. through attached wires.) The chosen material must be biocompatible with minimal irresolvable inflammatory response to allow intimate contact with regenerated nerve tissue and mechanically compatible with the surrounding nervous tissue.

We have utilized electrospinning and projection lithography as tools to create conductive, porous networks of non-woven biocompatible fibers in order to meet the materials requirements for the neural interface. The biocompatible fibers were based on the known biocompatible material poly(dimethyl siloxane) (PDMS) as well as a newer biomaterial material developed in our laboratories, poly(butylene fumarate) (PBF). Both of the polymers cannot be electrospun using conventional electrospinning techniques due to their low glass transition temperatures, so in situ crosslinking methodologies were developed to facilitate micro- and nano-fiber formation during electrospinning. The conductivity of the electrospun fiber mats was controlled by varying the loading with multi-walled carbon nanotubes (MWNTs).

Keywords

biomaterialpolymertissue
Type
Articles
Information
MRS Online Proceedings Library (OPL) , Volume 1418: Symposium LL/MM – Gels and Biomedical Materials , 2012 , mrsf11-1418-mm05-05
Copyright
Copyright © Materials Research Society 2012

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Bosworth, L.A. and , D. S., eds. Electrospinning for Tissue Regeneration. 2011, Woodhead Publishing Ltd.: Oxford.10.1533/9780857092915CrossRefGoogle Scholar
2.Zoroya, G., Increased foot patrols up troops’ limb injuries, in USA Today 2011.Google Scholar
3.Normann Richard, A., Technology insight: future neuroprosthetic therapies for disorders of the nervous system. Nat Clin Pract Neurol, 2007. 3(8): p. 444–.CrossRefGoogle ScholarPubMed
4.Rutten, W.L.C., Selective electrical interfaces with the nervous system. Annu. Rev. Biomed. Eng., 2002. 4: p. 407–452.CrossRefGoogle ScholarPubMed
5.Polasek, K.H., et al. ., Intraoperative evaluation of the spiral nerve cuff electrode on the femoral nerve trunk. J Neural Eng, 2009. 6(6): p. 066005.CrossRefGoogle ScholarPubMed
6.Rydevik, B.L., et al. ., An in vitro mechanical and histological study of acute stretching on rabbit tibial nerve. J Orthop Res, 1990. 8(5): p. 694–701.CrossRefGoogle Scholar
7.Cicotte, K.N., Dirk, S.M., and Hedberg-Dirk, E.L., Poly(1,3-butylene fumerate) and poly(1,3-butylene fumerate)-co-(1,3-butylene maleate) as electrospun scaffold materials. Mater. Res. Soc. Symp. Proc., 2010. 1239(Micro- and Nanoscale Processing of Biomaterials): p. No pp given, Paper #: 1239-VV05-02.Google Scholar
8.Cicotte, K.N., Hedberg-Dirk, E.L., and Dirk, S.M., Synthesis and electrospun fiber mats of low Tg poly(propylene fumarate-co-propylene maleate). J. Appl. Polym. Sci., 2010. 117(4): p. 1984–1991.CrossRefGoogle Scholar
9.Muskin, J., Ragusa, M., and Gelsthorpe, T., Three-Dimensional Printing Using a Photoinitiated Polymer. J. Chem. Educ., 2010. 87(5): p. 512–514.CrossRefGoogle Scholar
10.Bertsch, A., Jezequel, J.Y., and Andre, J.C., Study of the spatial resolution of a new 3D microfabrication process: the microstereophotolithog. using a dynamic mask-generator technique. J. Photochem. Photobiol., A, 1997. 107(1-3): p. 275–281.CrossRefGoogle Scholar
11.Kim, Y.B., Cho, D., and Park, W.H., Electrospinning of poly(dimethyl siloxane) by sol-gel method. J. Appl. Polym. Sci., 2009. 114(6): p. 3870–3874.CrossRefGoogle Scholar