Hostname: page-component-586b7cd67f-gb8f7 Total loading time: 0 Render date: 2024-11-30T18:13:00.159Z Has data issue: false hasContentIssue false
  • English
  • Français

Low-Density Microcellular Carbon Materials

Published online by Cambridge University Press:  29 November 2013

Get access

Extract

The low atomic number, good chemical reistance, and low thermal expansion of carbon foams make them attractive for many specialty applications. In general, we are interested in carbon LDMMs that have a maximum cell size of 25 μm and densities less than 0.05 g/cm3. These requirements are beyond the state of the art for most commercial carbon foams; thus, the DOE National Laboratories have concentrated on producing materials that meet these demanding requirements using various phase-separation, sol-gel, and replication processes.

In all cases, the final carbon foam is derived from a polymer precursor. Most polymers (e.g., polymethyl methacrylate) simply depolymerize and revert to their monomeric form when heated to high temperatures in an inert atmosphere. Cross-linked phenol-formaldehyde and polyfurfuryl alcohol are polymers that leave substantial carbon chars (greater than 50 wt%) after pyrolysis near 1000°C. Polyacrylonitrile also leaves a large carbon char (˜40 wt%)) after partial oxidation at 200°C followed by heat treatment at 1000°C. The latter char is a partially ordered graphite while the former chars are totally amorphous.

The microstructure and properties of carbon LDMMs depend on synthetic procedure and heat treatment conditions. We have been able to make carbon LDMMs with cell sizes as small as 100 Å or with densities as low as 0.015 g/cm3. Furthermore, surface areas of 50–1000 m2/g have been obtained with microstructures ranging from ribbonlike webs to interconnected colloidal-like particles. The ability to control these various parameters presents new opportunities to design carbon LDMMs for high technology applications, examples of which include sensors, electrodes, and high temperature filters.

Type
Technical Feature
Information
MRS Bulletin , Volume 15 , Issue 12 , December 1990 , pp. 37 - 40
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Jenkins, G.M. and Kawamura, K., Polymeric Carbons - Carbon Fibre, Glass and Char (Cambridge University Press, Cambridge, 1976).Google Scholar
2.Pekala, R.W. and Kong, F.M., Polym. Preprints 30(1) (1989) p. 221.Google Scholar
3.Kinoshita, K., Carbon (John Wiley & Sons, New York, 1988).Google Scholar
4.LeMay, J.D., Tillotson, T.M., Hrubesh, L.W., and Pekala, R.W., in Better Ceramics Through Chemistry IV, edited by Brinker, C.J., Clark, D.E., Ulrich, D.R., and Zelinski, B.J. (Mater. Res. Soc. Symp. Proc. 180, Pittsburgh, PA, 1990) p. 321.Google Scholar
5.Pekala, R.W., Alviso, C.T., and LeMay, J.D., J. Non-Cryst. Solids, in press.Google Scholar
6.Williams, J.M. and Nyitray, A.M., Los Alamos National Laboratory, (private communication).Google Scholar
7.Kong, F.M., Polym. Preprints 30(2) (1989) p. 258.Google Scholar
8.Pekala, R.W. and Hopper, R.W., J. Mater. Sci. 22 (1987) p. 1840.CrossRefGoogle Scholar
9.Pekala, R.W. and Hopper, R.W., U.S. Patent No. 4 756 898 (July 12, 1988); U.S. Patent No. 4 806 290 (February 21, 1989).Google Scholar
10.Weber, J.N. and White, E.W., Miner. Sci. Eng. 5(2) (1973) p. 151.Google Scholar
11.White, E.W., Hanusiak, H.M., and White, R.A., U.S. Patent No. 4 075 092 (February 21, 1978).Google Scholar
12.Koehler, F.A. and Smith, S.D., EG&G Mound Laboratory (private communication).Google Scholar
13.Nissen, D., Sandia National Laboratories-Livermore, (private communication).Google Scholar
14.Sylwester, A.P., Aubert, J.H., Rand, P.B., Arnold, C. Jr., and Clough, R.L., Polym. Mater. Sci. Eng. 57 (1987) p. 113.Google Scholar