Recently, a new 2D carbon allotrope structure, named phagraphene (PG), was proposed. PG has a densely array of penta-hexa-hepta-graphene carbon rings. PG was shown to present low and anisotropic thermal conductivity and it is believed that this anisotropy should be also reflected in its mechanical properties. Although PG mechanical properties have been investigated, a detailed and comprehensive study is still lacking. In the present work we have carried out fully atomistic reactive molecular dynamics simulations using the ReaxFF force field, to investigate the mechanical properties and fracture patterns of PG membranes. The Young’s modulus values of the PG membranes were estimated from the stress-strain curves. Our results show that these curves present three distinct regimes: one regime where ripples dominate the structure and mechanical properties of the PG membranes; an elastic regime where the membranes exhibit fully planar configurations; and finally am inelastic regime where permanent deformations happened to the PG membrane up to the mechanical failure or fracture.

Here we present an investigation into the phase change mechanism and detection methods of the metal-insulator transition of vanadium dioxide (VO2). We are able to detect the onset of the phase transition, and track it to completion using both the mechanical and electrical response by depositing VO2/TiO2 layers onto microcantilever devices by pulsed laser deposition. The resonance frequency of v-shaped cantilevers was shown to increase by up to 41 % upon deposition of VO2 as detected by laser Doppler vibrometry. Such a large increase in resonance frequency is ascribed to high tensile stress imparted onto the cantilever during the deposition process. The insulator-metal transition manifested as a 5 % increase in the resonance frequency as a result of lattice compression, resulting in additional tensile stress in the more ordered metallic phase. Electrically, the transition was confirmed by over three orders magnitude decrease in resistance upon heating past the transition. The metal-insulator transition was measured with an accuracy of a few °C when comparing the two methods, however, the transition was much sharper in the mechanical response.

ZnFe2O4 (ZFO) represents a promising anode material for lithium ion batteries, but there is still a lack of deep understanding of the fundamental reduction mechanism associated with this material. In this paper, the complete visualization of reduction/oxidation products irrespective of their crystallinity was achieved experimentally through a compilation of in situ X-ray diffraction, synchrotron based powder diffraction, and ex-situ X-ray absorption fine structure data. Complementary theoretical modelling study further shed light upon the fundamental understanding of the lithiation mechanism, especially at the early stage from ZnFe2O4 up to LixZnFe2O4 (x = 2).

The design of the surface chemistry of colloidal semiconductor nanocrystals (NCs) presents a powerful synthetic approach that allows to tune the optical and electronic properties of the particles in independent and precisely desired manner, to provide chemical and colloidal stability in diverse media, and, finally, to control their targeted applicability ranging from catalysis, medicine to advanced electronic devices. In this article, we summarize the successful functionalization of colloidal NCs with specifically chosen ligands using a novel ligand-exchange strategy. To transform diverse colloidal NCs into a competitive class of solution-processed semiconductors for electronic applications, we replaced the pristine, insulating ligands with tiny inorganic and hybrid inorganic/organic species. The surface modification with inorganic ions modulates the charge carrier density in NC units and guarantees enhanced interparticle interactions. The subsequent functionalization of the all-inorganic-capped NCs with organic molecules leads to the formation of hybrid inorganic/organic-capped NCs. For example, the introduction of short amine molecules enables to preserve the optical and electronic characteristics of their all-inorganic counterparts, while extending the solubility range and improving the ability to form long-range ordered 2D and 3D superstructures. Moreover, these short amines can be further used as convenient axillary co-ligands facilitating the surface functionalization of all-inorganic NCs with other biocompatible molecules, such as polyethylene glycol (PEG). This opens further perspectives for NCs not only in optoelectronic but also in biological and medical applications.

The objective of this paper is to demonstrate that Ag readily diffuses into Sb2S3 and that electric fields can control the diffusion. Ag diffusion influences the crystallization temperature and electrical properties of Sb2S3. We studied the interface between Ag and Sb2S3 using X-ray reflectivity and show that the Ag cations can be controlled by applying an electric field. We believe this effect has technological applications in data storage devices.

The effects of different starting materials using nano-synthesis methodology on electrochemical performance of lithium manganese oxide (LixMn2O4) are studied. Four spinel-type LixMn2O4 (LMO) cathode materials were prepared with different lithium and manganese sources and were analyzed chemically and characterized by BET and XRD. The electrochemical performance of the cathodes at room temperature and elevated temperature was tested. The crystal structure was indexed to be a cubic system with lattice parameters of 8.2342 ±0.170 Å and defined to the space group Fd3m. There was no peak of impurity because the raw materials for Mn source were first treated with acid. Although the results showed that the structures of the samples were confirmed to be cubic spinel structure, the lattice parameter and specific surface area of the samples were different. The LiMn2O4 cathodes have an initial discharge capacity of over 120mAh/g and show an ordinary two-step voltage profile. The results demonstrated that the cathode materials prepared with LiNO3 as Li source have larger lattice parameters, than those prepared from LiOH·H2O as Li source. The cathode prepared from Electrochemical Manganese Dioxide (EMD) as Mn source have larger particle sizes, lower first charge and discharge capacity, better cyclic performance, whereas those from Chemical Manganese Dioxide (CMD) as Mn source have smaller particle size, higher first charge and discharge capacity, and poor cyclic stability at elevated temperature. The cell polarization of the cathode developed by LiOH•H2O and EMD was identified to be the least and the elevated temperature cycelability to be the best. These manifestations can be attributed to differences in Li and Mn sources, specific surface areas, purities of starting materials and synthesis conditions. Melt-impregnation as a nano-synthesis method proved to be an excellent method to synthesize LiMn2O4 cathode materials that can operate at elevated temperatures when using correct starting materials and good control of synthesis temperatures.

This work presents the synthesis and characterization of TiO2 nanotubes (NTT) with chitosan (CS). In a first stage, electrochemical anodization of titanium foils was used to generate NTT in a membrane-type arrangement. From these experiments, suitable experimental conditions were selected. In a second stage, the synthesized NTT were detached from the titanium foils by sonication. In the third stage, the detached NTT were dispersed in an acid solution containing CS in various concentrations. Finally, the nanotubes-chitosan (NTT/CS) samples were characterized by Scanning Electron Microscopy (SEM), X-ray diffraction (XRD), and Fourier Transform Infrared Spectrometry (FTIR). Our results showed that the NTT presented very regular tube morphology with -OH and Ti-O- functional groups on the surface. The interaction of NTT and chitosan was enhanced by increasing the time of contact during the synthesis of the titanium composites.

Transition metal dichalcogenides (TMDC), such as MoS2, WS2 have attracted attention due to their mechanical and electronic properties in their two dimensional (2D) structures. Here, we report a facile growth of monolayer TMDC using oxide source materials with the assistant of NaCl. The addition of NaCl can enhance the lateral growth and widen the growth window of TMDC. Through carefully controlling the growth parameters, large area growth of TMDC can be achieved. Two steps E-beam lithography was utilized to fabricate electrodes of TMDC. The phototransistors made from the CVD grown TMDC show strong persistent photoconductivity (PPC). It was finally shown that TMDC device capping with h-BN could have suppressed PPC effects.