Hostname: page-component-586b7cd67f-rdxmf Total loading time: 0 Render date: 2024-11-28T02:33:23.988Z Has data issue: false hasContentIssue false
  • English
  • Français

Graphene Delivery Systems for Hierarchical Fiber Reinforced Composites

Published online by Cambridge University Press:  05 February 2016

Yan Li ,
Han Zhang ,
Ton Peijs  and
Emiliano Bilotti
Yan Li
Affiliation:
School of Engineering and Materials Science, Queen Mary University of London, Mile End Road, E1 4NS, London, UK. Nanoforce Technology Ltd., Joseph Priestley Bld., Mile End Road, E1 4NS London, UK
Han Zhang
Affiliation:
School of Engineering and Materials Science, Queen Mary University of London, Mile End Road, E1 4NS, London, UK. Nanoforce Technology Ltd., Joseph Priestley Bld., Mile End Road, E1 4NS London, UK
Ton Peijs
Affiliation:
School of Engineering and Materials Science, Queen Mary University of London, Mile End Road, E1 4NS, London, UK. Nanoforce Technology Ltd., Joseph Priestley Bld., Mile End Road, E1 4NS London, UK
Emiliano Bilotti*
Affiliation:
School of Engineering and Materials Science, Queen Mary University of London, Mile End Road, E1 4NS, London, UK. Nanoforce Technology Ltd., Joseph Priestley Bld., Mile End Road, E1 4NS London, UK
*
*(Email: [email protected])
Get access

Abstract

Three different methods are evaluated for the introduction of graphene nanoplatelets (GNP) in hierarchical carbon- or glass fiber reinforced plastics. They involve; (1) direct infusion of GNP filled epoxy resin, (2) spray coating of GNP on fiber preforms and (3) the use of dissolvable thermoplastic interleaf carrier films. Direct infusion of GNP filled resin is the easiest method to deliver GNP into composite laminates but may lead to viscosity and filtration issues. Automated spray coating was set up to manufacture GNP modified carbon- or glass fiber fabrics, while graphene filled phenoxy interleaf films were manufactured by bar coating, both followed by resin infusion using neat epoxy resin to produce GNP modified epoxy laminates, without the disadvantages of GNP filled resins. No substantial difference in interlaminar shear strength (ILSS) for composites manufactured using the different delivery methods is found. However, the electrical conductivity of the GNP modified glass-fiber composites manufactured by spray coating of glass fabrics is two orders of magnitude higher than for laminates made by direct infusion of GNP modified resin.

Keywords

compositefiberelectrical properties
Type
Articles
Information
MRS Advances , Volume 1 , Issue 19: Nanomaterials and Synthesis , 2016 , pp. 1339 - 1344
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Huang, X., et al. , Graphene-based composites. Chemical Society Reviews, 2012. 41(2): p. 666–686.Google Scholar
Nika, D., et al. , Lattice thermal conductivity of graphene flakes: Comparison with bulk graphite. Applied Physics Letters, 2009. 94(20): p. 203103.CrossRefGoogle Scholar
Lee, C., et al. , Measurement of the elastic properties and intrinsic strength of monolayer graphene. Science, 2008. 321(5887): p. 385–388.CrossRefGoogle ScholarPubMed
Grantab, R., et al. , Anomalous strength characteristics of tilt grain boundaries in graphene. Science, 2010. 330(6006): p. 946–948CrossRefGoogle ScholarPubMed
Zhang, H., et al. , The use of carbon nanotubes for damage sensing and structural health monitoring in laminated composites: a review, Nanocomposites, 2015CrossRefGoogle Scholar
Zhang, H., et al. , Improved fracture toughness and integrated damage sensing capability by spray coated CNTs on carbon fibre prepreg, Composites Part A: Appl. Sci. Manuf., 2015, 70, p. 102–110.Google Scholar
Zhang, H., et al. , Localized toughening of carbon/epoxy laminates using dissolvable thermoplastic interleaves and electrospun fibres, Composites Part A: Appl. Sci. Manuf., 2015, 79, p. 116–126.CrossRefGoogle Scholar
Hernandez, Y., et al. High-yield production of graphene by liquid-phase exfoliation of graphite, Nature Nanotechnology, 2008, 3(9), p. 563–568.Google Scholar
Li, Y., et al. , Optimization of three-roll mill parameters for in-situ exfoliation of graphene, In MRS Proceedings, p. mrsf15–2336096. Cambridge Univ. Press, 2015.Google Scholar
Sadeghian, R., et al. , Manufacturing carbon nanofibers toughened polyester/glass fiber composites using vacuum assisted resin transfer molding for enhancing the mode-I delamination resistance. Composites Part A: Appl. Sci. Manuf., 2006. 37(10): p. 1787–1795.CrossRefGoogle Scholar
Da Costa, E.F.R., et al. , RTM processing and electrical performance of carbon nanotube modified epoxy/fibre composites. Composites Part A: Appl. Sci. Manuf., 2012. 43(4): p. 593–602.Google Scholar