Two-dimensional electromagnetic particle-in-cell simulations are carried out to investigate the effect of ion-to-electron mass ratio on the evolution of warm electron beam-plasma instability. Four cases are considered: A: mi/me = 0 (two-electron stream instability); B: mi/me = 1 (pair plasma); C: mi/me = 100; and D: mi/me = 1000. It is shown that the generation of Langmuir waves in the fundamental mode of electron plasma frequency and the subsequent dynamics of large-amplitude solitons are not affected by the ion species. However, it determines the decay process of solitons and the excitation of electromagnetic waves in the second harmonic. In the first two cases, mi/me = 0 and 1, there is no sign of emission in the second harmonic, while the strongest emission in the second harmonic is found for the case of largest mass ratio, mi/me = 1000. This confirms the two-step wave-wave coupling mechanism for the generation of second harmonic electromagnetic waves, which requires the excitation of ion-acoustic waves in the first step. Moreover, the dispersion diagrams of all excited waves are presented.

In this work, we present experimental results on the behavior of liquid water at megabar pressure. The experiment was performed using the HIPER (High-Intensity Plasma Experimental Research) laser facility, a uniaxial irradiation chamber of GEKKO XII (GXII) at the Institute of Laser Engineering (ILE), and the PHELIX at GSI (GSI Helmholtz Centre for Heavy Ion Research), a single-beam high-power laser facility, to launch a planar shock into solid multilayered water samples. Equation-of-state data of water (H2O are obtained in the pressure range 0.50–4.6 Mbar by tuning the laser-drive parameters. The Hugoniot parameters (pressure, density, etc.) and the shock temperature were simultaneously determined by using VISAR and SOP as diagnostic tools and quartz as the standard material for impedance mismatch experiments. Finally, our experimental results are compared with hydrodynamic simulations tested with different equations of state, showing good compatibility with tabulated SESAME tables for water.

In the present paper, filamentous structure formation, associated turbulent spectrum, and density cavity formation phenomena have been investigated for low-β plasma $\left(\beta \ll m_e/m_i\right)$ applicable to the auroral region. A set of dimensionless equations governing the dynamics of three dimensionally propagating inertial Alfvén wave (3D-IAW) and perpendicularly propagating magnetosonic wave (PMSW) has been developed. Ponderomotive force due to 3D-IAW has been included in the dynamics of the PMSW. Numerical simulation has been performed to study the nonlinear coupling of these two waves. From the obtained results, we found that the field intensity localization takes place which may further lead to the additional dissipation/turbulence process for particle heating and acceleration in space plasma. The associated turbulent spectrum is obtained with scaling nearly k−4.28 at smaller scales (in the dissipation range). Relevance of the obtained results with the observations reported by various spacecrafts such as Hawkeye and Heos 2 has been discussed. Also, density fluctuations (depletion) of ∼0.10 n0 are calculated, which are consistent with the FAST spacecraft observation reported.

To accelerate high-intensity heavy-ion beams to high energy in the booster ring (BRing) at the High-Intensity Heavy-Ion Accelerator Facility (HIAF) project, we take the typical reference particle 238U35+, which can be accelerated from an injection energy of 17 MeV/u to the maximal extraction energy of 830 MeV/u, as an example to study the basic processes of longitudinal beam dynamics, including beam capture, acceleration, and bunch merging. The voltage amplitude, the synchronous phase, and the frequency program of the RF system during the operational cycle were given, and the beam properties such as bunch length, momentum spread, longitudinal beam emittance, and beam loss were derived, firstly. Then, the beam properties under different voltage amplitude and synchronous phase errors were also studied, and the results were compared with the cases without any errors. Next, the beam properties with the injection energy fluctuation were also studied. The tolerances of the RF errors and injection energy fluctuation were dictated based on the CISP simulations. Finally, the effect of space charge at the low injection energy with different beam intensities on longitudinal emittance and beam loss was evaluated.

A compact high-power ultra-wideband bipolar pulse generator based on a modified Marx circuit is designed, which is mainly composed of a primary power supply, Marx generator, sharpening and cutoff subnanosecond spark gap switches, and coaxial transmission lines. The Marx generator with modified circuit structure has thirty-two stages and is composed of eight disk-like modules. Each module consists of four capacitors, two spark gap switches, four charging inductors, and a mechanical support. To simplify the design of the charging structure and reduce the number of switches, four groups of inductors are used to charge the capacitors of the Marx generator, two of which are used for positive voltage charging and the other two for negative voltage charging. When the capacitor of each stage is charged to 35 kV, the maximum output peak voltage can reach 1 MV when the Marx generator is open circuit. The high-voltage pulse generated by the Marx generator charges the transmission line and forms a bipolar pulse through sharpening and cutoff switches. All transmission lines used for bipolar pulse generation have an impedance of 10 Ω. When the 950 kV pulse voltage generated by the Marx generator is fed into the transmission line, the bipolar pulse peak voltage can reach 390 kV, the center frequency of the pulse is about 400 MHz, and the output peak power is about 15.2 GW.

Based on the path encoding pulse compression teleology, a novel method for obtaining high-power microwave (HPM) pulse with ultrahigh repetition frequency is proposed in this paper. The mechanism of the path encoding pulse compression teleology is first introduced. And then, the obtained HPM pulse is analyzed. Theoretical analysis shows that the peak power of MW level and the repetition frequency of MHz level for the generated HPM pulse can be easily reached. To demonstrate the effectiveness of this method for obtaining HPM pulse with ultrahigh repetition frequency characteristic, a HPM-obtaining experiment was carried out based on an S-band microwave source. The HPM pulses with the width of 1 ns, 2 ns, and 3 ns are studied, respectively. The measured results show that the HPM pulse with the power higher than 100 kW and the repetition frequency of 250 kHz at the frequency of 2.856 GHz is easily obtained. The repetition frequency of the generated HPM pulse can be easily changed. Because the pulse with the power higher than 100 kW and the repetition frequency of several hundreds of kHz is obtained for the first time, this type of pulse will have a broad prospect of application in the communication, radar, and electronic countermeasure fields. In addition, the effect experiment of interfering communication and control links was carried out by utilizing the ultrahigh repetition frequency characteristic of the generated HPM pulse. Also, the experiment results show the feasibility of this pulse for interfering the communication and control links.

The characterization of energetic protons generated in the ShenGuang-II UP petawatt laser interactions with foil targets has been systematically studied. The proton energy spectra and angular distributions are measured with a radiochromic film stack. It shows that the proton energy spectra have a Boltzmann distribution with temperature of about 2.8 MeV and cutoff energy of about 20 MeV. The divergence angles of protons vary from 10° to 60°, dependent on the proton energy. The proton source size and location are investigated via the proton point-projection mesh imaging. The proton virtual sources are found to locate tens to hundreds of microns in front of the foil target, depending on the proton energies. A Monte Carlo simulation estimates the diameter of the virtual proton source to be about 12 μm for the protons with energy of 16.8 MeV, which is much smaller than the laser focus size of about 50 μm. The spatial resolution of the 16.8 MeV proton imaging is quantified with the point spread function to be about 15 μm, which is consistent with the proton virtual source size. These results will be important for the users conducting experiments with the protons as a backlighting source on the ShenGuang-II UP petawatt laser.

The advent of high-energy short-pulse laser beams poses new problems related to radiation protection. The radiation generated in experiments using multipetawatt laser systems leads to prompt doses and potentially to the activation of the materials within the interaction chamber and the experimental hall. Despite many new PW laser facilities are nowadays entering into operation, this question has received little attention until now. In this paper, we evaluate the radiological effects induced by the operation of a high-power laser facility. Two working regimes are considered related to the production of hard X-rays and energetic protons. The methodology is general and may be applied for the design of experiments with any high-power laser systems.

Effects of solid nanolayers embedded in a near-critical density plasma on the laser-driven collisionless shock acceleration are investigated by using two-dimensional particle-in-cell simulations. Due to the interaction of nanolayers and the incident laser, an additional number of hot electrons are generated and an inhomogeneous magnetic field is induced. As a result, the collisionless shock is reinforced within the nanolayer gaps compared to the target without the structured nanolayers. When the laser intensity is 9.8 × 1019 W/cm2, the amplitude of the electrostatic field is increased by 30% and the shock velocity is increased from 0.079c to 0.091c, leading to an enhancement of the peak energy and the cutoff energy of accelerated protons, from 6.9 MeV to 9.1 MeV and 12.2 MeV to 20.0 MeV, respectively. Furthermore, the effects of the width of the nanolayer gaps are studied, by adjusting the gap width of nanolayers, and optimal nanolayer setups for collisionless shock acceleration can be acquired.

Laser-induced damage threshold is the main limitation for fused silica optics in high-power laser applications. The existence of various defects near the surface is the key factor for the degradation of the threshold. In this work, the photoluminescence spectra at different regions of the damaged and recovered fused silica samples are recorded to analyze the correlation between photoluminescence of surface defects and laser-induced damage threshold. The experimental data concluded the inverse proportional correlation between fluorescence and laser-induced damage threshold value. The weak photoluminescence is the guarantee of the high laser-induced damage threshold, and then the higher local Si nanocluster concentration corresponds with the higher laser-induced damage threshold value for the fused silica optics after CO2 laser treatment. The investigation reveals that photoluminescence measurement can be employed to check the quality of pristine fused silica and evaluate the tendency of the laser-induced damage threshold value. The current results are helpful for understanding the evolution of interaction from CO2 laser treatment and fused silica optics and can provide the guide of process technology for the high quality of fused silica optics.

A detailed study of direct laser-driven electron acceleration in paraxial Laguerre–Gaussian modes corresponding to helical beams LG0m with azimuthal modes m = {1,2,3,4,5} is presented. Due to the difference between the ponderomotive force of the fundamental Gaussian beam LG00 and helical beams LG0m, we found that the optimal beam waist leading to the most energetic electrons at full width at half maximum is more than twice smaller for the latter and corresponds to a few wavelengths Δw0 = {6,11,19}λ0 for laser powers of P0 = {0.1, 1,10} PW. We also found that, for azimuthal modes m ≥ 3, the optimal waist should be smaller than Δw0 < 19λ0. Using these optimal values, we have observed that the average kinetic energy gain of electrons is about an order of magnitude larger in helical beams compared to the fundamental Gaussian beam. This average energy gain increases with the azimuthal index m leading to collimated electrons of a few 100 MeV energy in the direction of the laser propagation.

Stimulated Raman forward scattering (SRFS) of an intense X-mode laser pump in a preformed parabolic plasma density profile is investigated. The laser pump excites a plasma wave and one/two electromagnetic sideband waves. In Raman forward scattering, the growth rate of the parametric instability scales as two-third powers of the pump amplitude and increases linearly with cyclotron frequency.

For low carbon energy generation, a very large exchange of electricity generators is existentially vital within the next number of years by power stations preferably at considerably low cost than the present installations. When considering the million times higher nuclear energy per reaction than chemical, the usual hydrogen fusion with abundant boron fuel is used for environmentally clean electricity generators. Instead of usually needed ignition temperatures of hundreds of million degrees Celsius, it is possible to use nonthermal ignition pressures from now available CPA laser pulses. In this non-LTE scheme, there is no need for high compression, the medium of hydrogen-boron-11 temperatures is low, and therefore the bremsstrahlung losses practically do not exist. The neutron, created by secondary reactions, elimination device includes tin and is arranged such that the neutrons are brought to nuclear reactions with the tin. We suggest adding the tin that has proven to be particularly advantageous because of its high effective cross section, and the neutron reactions with tin transform the tin nuclei into stable nuclei with a higher atomic weight.

The perturbation electron density and stopping power caused by the movement of charged particles above two-dimensional quantum electron gases (2DQEG) have been studied in numerous works using the quantum hydrodynamic (QHD) theory. In this paper, the QHD is modified by introducing the two-dimensional electron exchange-correlation potential at high density Vxc2DH and the pump wave modulations. Based on the modified QHD, the perturbation electron density and stopping power are calculated for pump waves with various parameters. The results show that the stopping power values are more accurate after considering Vxc2DH. Under the modulation of pump waves with the wavelength from 0.1nm to 0.1cm, the perturbation electron density of 2DQEG and the stopping power of charged particles show periodic changes. Under the modulation of pump waves with λ = 1.76 × 10−4 cm and ${\mathrm{\Phi }}_0=2\times {10}^{10}e/{\lambda }_f$, the average stopping power with respect to the time phase θ becomes negative, which means that the charged particles will gain energy and can be accelerated. This is a new phenomenon in the fields of 2DQEG and of great significance in surface physics and surface modification in nanoelectronic devices with beam matter interactions.

Energy loss of protons with 90 and 100 keV energies penetrating through a hydrogen plasma target has been measured, where the electron density of the plasma is about 1016 cm−3 and the electron temperature is about 1-2 eV. It is found that the energy loss of protons in the plasma is obviously larger than that in cold gas and the experimental results based on the Bethe model calculations can be demonstrated by the variation of effective charge of protons in the hydrogen plasma. The effective charge remains 1 for 100 keV protons, while the value for 90 keV protons decreases to be about 0.92. Moreover, two empirical formulae are employed to extract the effective charge.

Foilless diode are widely used in high-power microwave devices, but the traditional foilless diodes have large volume, heavy weight, and high power consumption, which are not conducive to the application of high-power microwave system on mobile platform. In order to reduce the size of the foilless diode, improve the transmission efficiency of electron beams, and reduce the weight and power consumption of the guiding magnetic field system, an axial foilless diode with a composite guiding magnetic field system is developed in this paper. By adjusting the structure size and magnetic field parameters of solenoid coil, permanent magnet, and soft magnet, the configuration of the composite magnetic field is optimized. The diameter of the anode tube is about 40% smaller than that of the original structure, and the weight and power consumption of the guiding magnetic system are about 40% lower than that of the original system when the same axial magnetic field intensity in the uniform region is generated. When the magnetic field strength of the permanent magnet is set as 1.4 T and that of the solenoid coil is in the range of 0.5 T∼1 T, the electron beam transmission efficiency is 100%, and the diode impedance is adjustable in the range of 100 Ω∼240 Ω. The experimental results verify the correctness of the simulation analysis. The experimental results show that when the magnetic field strength of the solenoid coil is 0.98 T (0.5 T) and that of the permanent magnet is 1.4 T, the transmission efficiency of the high-current annular electron beam with a peak voltage of 636 kV (590 kV) and a peak current of 3.3 kA (2.6 kA) is 100%, and the diode impedance is about 194 Ω (220 Ω).

Terahertz (THz) radiation from a plasma cylinder with embedded radial electric and axial magnetic fields is investigated. The plasma density and the electric and magnetic fields are such that the electron plasma frequency is near the electron cyclotron frequency and in the THz regime. Two-dimensional particle-in-cell simulations show that the plasma electrons oscillate not only in the azimuthal direction but also in the radial direction. Spectral analysis shows that the resulting oscillating current pattern has a clearly defined characteristic frequency near the electron cyclotron frequency, suggesting resonance between the cyclotron and plasma oscillations. The resulting far-field THz radiation in the axial direction is also discussed.

It is shown that the dynamics of electrons accelerated in narrow capillary waveguides is significantly influenced by the parametric excitation of their betatron oscillations. On the one hand, this excitation can irreversibly spoil the emittance of an accelerated electron bunch that limits the possibilities of their practical use. On the other hand, controlled parametric excitation of betatron oscillations can be used to generate short-pulse sources of synchrotron radiation. The article analyzes the regions of parametric instabilities, their dependence on the parameters of accelerated electron bunches and guiding structures, and their influence on the dynamics of accelerated electrons. The parameters of the generated synchrotron radiation are also estimated. Measurements of the spectral parameters of synchrotron radiation can serve as a tool for diagnostics of betatron oscillations and their excitation in the case of parametric resonances.

With the development of high-power microwave technology, the output power of the pulse generator is required more and more higher. In this paper, it is realized by increasing the output power of the module while the output impedance of the module changes little. The module of the generator is based on pulse forming network (PFN) and linear transformer (LT). Four Blumlein PFNs with arc-type configuration and 24 Ω characteristic impedance were connected symmetrically to the primary coil of the LTD and driven by two identical laser triggered spark switches to ensure four Blumlein PFNs synchronizing operation. On this basis, a two-stage high-power pulse generator based on PFN-LT is developed. The following technical parameters of the generator were achieved on a 12 Ω high-power solid resistor: output voltage amplitude of ∼250 kV and output power of ∼5.2 GW at a repetition rate of 5 Hz.

The two-dimensional snake scanning of the CCD method provides an effective solution to measure small-scale light spots which are smaller than one CCD pixel. The influences of the A/D conversion digits and response uniformity of the CCD on the measurement error are studied. When the A/D conversion digit is 20, the measurement error can be ignored. The maximum error value of the nonuniform response of the CCD pixel when the order of the super-Gaussian function is 10 is 0.7 μm. The research results can be used to guide the experiment.