Hostname: page-component-586b7cd67f-gb8f7 Total loading time: 0 Render date: 2024-11-24T20:19:32.820Z Has data issue: false hasContentIssue false
  • English
  • Français

Vacuum brazing of TC4 alloy to AlMgB14–TiB2 ceramic using AgCu filler

Published online by Cambridge University Press:  07 May 2019

Shengpeng Hu ,
Yu Lei ,
Xiaoguo Song ,
Wei Fu ,
Yun Luo  and
Yuzhen Lei
Shengpeng Hu
Affiliation:
State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China; and Shandong Provincial Key Laboratory of Special Welding Technology, Harbin Institute of Technology at Weihai, Weihai 264209, China
Yu Lei
Affiliation:
State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China; and Shandong Provincial Key Laboratory of Special Welding Technology, Harbin Institute of Technology at Weihai, Weihai 264209, China
Xiaoguo Song*
Affiliation:
State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China; and Shandong Provincial Key Laboratory of Special Welding Technology, Harbin Institute of Technology at Weihai, Weihai 264209, China
Wei Fu
Affiliation:
State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China
Yun Luo
Affiliation:
Shandong Provincial Key Laboratory of Special Welding Technology, Harbin Institute of Technology at Weihai, Weihai 264209, China
Yuzhen Lei
Affiliation:
Shandong Provincial Key Laboratory of Special Welding Technology, Harbin Institute of Technology at Weihai, Weihai 264209, China
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

AlMgB14–TiB2 ceramic was successfully brazed to TC4 alloy with inactive AgCu filler alloy. X-ray diffractometer, SEM, and energy-dispersive spectrometer were used to study interfacial microstructure and shear strength of the joints under different brazing temperatures. The results indicated that the typical microstructure of the TC4/AlMgB14–TiB2 joint was TC4/Ti(s.s) + Ti2Cu/Ti2Cu/TiCu/TiCu2Al/Ag(s.s) + Cu(s.s)/TiB whiskers/TiB2 reaction layer/AMBT. By increasing the brazing temperature, the thickness of the TC4 diffusion layer was improved, whereas that of the brazing seam decreased remarkably. When the brazing temperature was increased to 880 °C, the brazing seam was composed of Ti–Cu intermetallic Ag(s.s) with a few Cu(s.s), TiCu2Al distributed. Meanwhile, the formation of a continuous TiB2 reaction layer at the interface of the AMBT and brazing filler facilitated the improvement of joint shear strength. The joint with the maximum shear strength of 46.7 MPa was obtained while brazing at 880 °C for 10 min.

Keywords

AlMgB14brazinginterfacial microstructure
Type
Article
Information
Journal of Materials Research , Volume 34 , Issue 14 , 28 July 2019 , pp. 2535 - 2542
Copyright
Copyright © Materials Research Society 2019 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Russell, A.M., Cook, B.A., Harringa, J.L., and Lewis, T.L.: Coefficient of thermal expansion of AlMgB14. Scr. Mater. 46, 629 (2002).CrossRefGoogle Scholar
Cook, B.A., Harringa, J.L., Lewis, T.L., and Russell, A.M.: A new class of ultra-hard materials based on AlMgB14. Scr. Mater. 42, 597 (2000).CrossRefGoogle Scholar
Lei, Y., Meng, Q.S., Zhuang, L., Chen, S.P., and Dai, J.J.: Oxidation behavior of AlMgB14–TiB2 composite at elevated temperature. Appl. Surf. Sci. 347, 155 (2015).CrossRefGoogle Scholar
Tian, Y., Bastawros, A.F., Lo, C.C.H., Constant, A.P., Russell, A.M., and Cook, B.A.: Superhard self-lubricating AlMgB14 films for microelectromechanical devices. Appl. Phys. Lett. 83, 2781 (2003).CrossRefGoogle Scholar
Zhoua, T.Z.Y.M., Xu, K., Zhang, F.L., Baib, K., Huang, H.P., Wu, S.H., and Luo, S.M.: Effect of Y2O3 addition on microstructure and mechanical properties of spark plasma sintered AlMgB14 and AlMgB14–TiB2. Ceram. Int. 44, 8591 (2018).CrossRefGoogle Scholar
Bahadur, S. and Ahmed, A.: Chapter 16-abrasion of engineering ceramics: AlMgB14–TiB2 composite and other hard materials. Tribol. Interf. Eng. 51, 294 (2006).CrossRefGoogle Scholar
Ahmed, A., Bahadur, S., Cook, B.A., and Peters, J.: Mechanical properties and scratch test studies of new ultra-hard AlMgB14 modified by TiB2. Tribol. Int. 39, 129 (2006).CrossRefGoogle Scholar
Kevorkijan, V., Škapin, S.D., Jelen, M., Krnel, K., and Meden, A.: Cost-effective synthesis of AlMgB14–xTiB2. J. Eur. Ceram. Soc. 27, 493 (2007).CrossRefGoogle Scholar
Sciti, D., Bellosi, A., and Esposito, L.: Bonding of zirconia to super alloy with the active brazing technique. J. Eur. Ceram. Soc. 21, 45 (2001).CrossRefGoogle Scholar
Kim, J.H., Dong, S.K., Lim, S.T., and Kim, D.K.: Interfacial microstructure of diffusion-bonded SiC and Re with Ti interlayer. J. Alloys Compd. 701, 316 (2017).CrossRefGoogle Scholar
Zhang, G., Cai, J., Chen, B., and Xu, T.: Availability of in situ reinforced active-transient liquid phase bond with good wettability for 70 vol% SiCp/A356 composite using Al–Mg–Ga–Ti interlayer. Mater. Des. 110, 653 (2016).CrossRefGoogle Scholar
Yang, Y.F. and Mu, D.: Effect of Ni addition on the formation mechanism of Ti5Si3 during self-propagation high-temperature synthesis and mechanical property. J. Eur. Ceram. Soc. 34, 2177 (2014).CrossRefGoogle Scholar
Zhuang, L., Lei, Y., Chen, S., Hu, L., and Meng, Q.: Microstructure and mechanical properties of AlMgB14–TiB2 associated with metals prepared by the field-assisted diffusion bonding sintering process. Appl. Surf. Sci. 328, 125 (2015).CrossRefGoogle Scholar
Zhao, Y.X., Wang, M.R., Cao, J., Song, X.G., Tang, D.Y., and Feng, J.C.: Brazing TC4 alloy to Si3N4 ceramic using nano-Si3N4 reinforced AgCu composite filler. Mater. Des. 76, 40 (2015).CrossRefGoogle Scholar
Barrena, M.I., Matesanz, L., and Salazar, J.M.G.D.: Al2O3/Ti6Al4V diffusion bonding joints using Ag–Cu interlayer. Mater. Charact. 60, 1263 (2009).CrossRefGoogle Scholar
Zhao, Y., Song, X., Hu, S., Zhang, J., Cao, J., Fu, W., and Feng, J.C.: Interfacial microstructure and mechanical properties of porous-Si3N4 ceramic and TiAl alloy joints vacuum brazed with AgCu filler. Ceram. Int. 43, 9738 (2017).CrossRefGoogle Scholar
Villars, P., Prince, A., and Okamoto, H.: Handbook of Ternary Alloy Phase Diagrams (ASM International, Materials Park, Ohio, 1995).Google Scholar
Qiu, Q., Wang, Y., Yang, Z., and Wang, D.: Microstructure and mechanical properties of Al2O3 ceramic and Ti6Al4V alloy joint brazed with inactive Ag–Cu and Ag–Cu + B. J. Eur. Ceram. Soc. 36, 2067 (2016).CrossRefGoogle Scholar
Panda, K.B. and Ravi Chandran, K.S.: Synthesis of ductile titanium–titanium boride (Ti–TiB) composites with a beta-titanium matrix: The nature of TiB formation and composite properties. Metall. Mater. Trans. A 34, 1371 (2003).CrossRefGoogle Scholar
Fu, H.M., Wang, H., Zhang, H.F., and Hu, Z.Q.: In situ TiB-reinforced Cu-based bulk metallic glass composites. Scr. Mater. 54, 1961 (2006).CrossRefGoogle Scholar
He, P., Yang, W.Q., Lin, T.S., Jia, D.C., Feng, J.C., and Liu, Y.: Diffusion bonding of ZrB2–SiC/Nb with in situ synthesized TiB whiskers array. J. Eur. Ceram. Soc. 37, 2769 (2017).Google Scholar
Yang, Z.W., Wang, C.L., Wang, Y., Zhang, L.X., Wang, D.P., and Feng, J.C.: Active metal brazing of SiO2–BN ceramic and Ti plate with Ag–Cu–Ti + BN composite filler. J. Mater. Sci. Technol. 33, 1392 (2017).CrossRefGoogle Scholar
Yang, Z.W., Zhang, L.X., Chen, Y.C., Qi, J.L., He, P., and Feng, J.C.: Interlayer design to control interfacial microstructure and improve mechanical properties of active brazed Invar/SiO2–BN joint. Mater. Sci. Eng., A 575, 199 (2013).CrossRefGoogle Scholar
Asthana, R. and Singh, M.: Joining of partially sintered alumina to alumina, titanium: Hastealloy and C–SiC composite using Ag–Cu brazes. J. Eur. Ceram. Soc. 28, 617 (2008).CrossRefGoogle Scholar
Liu, M., Liu, C.F., Zhang, J., Tao, R., Zhang, Q., and Qi, Q.: Microstructure and mechanical properties of BN–Si3N4 and AlON joints brazed with Ag–Cu–Ti filler alloy. J. Eur. Ceram. Soc. 38, 1265 (2018).CrossRefGoogle Scholar
Mendez, P.F., Park, J-W., and Eagar, T.W.: Strain energy distribution in ceramic-to-metal joints. Acta Mater. 50, 883 (2002).Google Scholar
Shiue, R.K., Wu, S.K., and Chen, S.Y.: Infrared brazing of TiAl intermetallic using BAg-8 braze alloy. Acta Mater. 51, 1991 (2003).CrossRefGoogle Scholar
He, Y.M., Zhang, J., Sun, Y., and Liu, C.F.: Microstructure and mechanical properties of the Si3N4/42CrMo steel joints brazed with Ag–Cu–Ti + Mo composite filler. J. Eur. Ceram. Soc. 30, 3245 (2010).CrossRefGoogle Scholar
Wang, T., Zhang, J., Liu, C., and Wang, G.: Microstructure and mechanical properties of Si3N4/42CrMo joints brazed with TiNp modified active filler. Ceram. Int. 40, 6881 (2014).CrossRefGoogle Scholar