Hostname: page-component-586b7cd67f-t8hqh Total loading time: 0 Render date: 2024-11-28T07:00:24.293Z Has data issue: false hasContentIssue false

Characterization of Al–Fe–V–Si heat-resistant aluminum alloy components fabricated by selective laser melting

Published online by Cambridge University Press:  04 May 2015

Shaobo Sun
Affiliation:
School of Materials Science and Engineering, Beihang University, Beijing 100191, People's Republic of China
Lijing Zheng*
Affiliation:
School of Materials Science and Engineering, Beihang University, Beijing 100191, People's Republic of China
Yingying Liu
Affiliation:
School of Materials Science and Engineering, Beihang University, Beijing 100191, People's Republic of China
Jinhui Liu
Affiliation:
Modern Manufacturing Engineering Center, Heilongjiang Institute of Science and Technology, Harbin 150027, People's Republic of China
Hu Zhang
Affiliation:
School of Materials Science and Engineering, Beihang University, Beijing 100191, People's Republic of China
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Heat-resistant Al–8.5Fe–1.3V–1.7Si (wt%) aluminum alloy components were fabricated using selective laser melting (SLM). The as-built samples were examined in terms of density, chemical composition, surface morphologies, microstructures, and mechanical behavior. The results show that nearly full dense samples with the relative density of 99.3% can be produced. The chemical composition of the deposited material is close to that of the powder, presenting a limited aluminum loss and a low oxygen pickup. The SLM specimens consist of three typical zones: the fusion zone (FZ), the remelting border zone (RBZ), and the heat-affected zone (HAZ). Ultrafine continuous cellular α-Al networks are observed in the FZ. The HAZ exhibits fine rounded Al12(Fe,V)3Si particles (10–70 nm) distributed homogeneously in the α-Al matrix, while the rectangle-like AlmFe-type phase (m = 4.0–4.4) with 100–500 nm in size is preferably formed in the RBZ. The microhardness of the parts shows directional independent, with a mean value of 246 HV0.1.

Type
Articles
Copyright
Copyright © Materials Research Society 2015 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Skinner, D.J., Bye, R.L., Raybould, D., and Brown, A.M.: Dispersion strengthened Al–Fe–V–Si alloys. Scr. Metall. 20, 867 (1986).Google Scholar
Skinner, D.J.: Dispersion Strengthened Aluminium Alloys, Kim, Y-W. and Griffith, W.M. eds.; TMS: Warrendale, PA, 1988; pp. 181197.Google Scholar
Li, P.Y., Yu, H.J., Chai, S.C., and Li, Y.R.: Microstructure and properties of rapidly solidified powder metallurgy Al–Fe–Mo–Si alloys. Scr. Mater. 49, 819 (2003).Google Scholar
Frank, R.E. and Hawk, J.A.: Effect of very high temperatures on the mechanical properties of Al–Fe–V–Si alloy. Scr. Metall. 23, 113 (1989).CrossRefGoogle Scholar
Khatri, S.C., Lawley, A., and Koczak, M.J.: Creep and microstructural stability of dispersion strengthened Al–Fe–V–Si–Er alloy. Mater. Sci. Eng., A 167, 11 (1993).Google Scholar
Hariprasad, S., Sastry, S.M.L., Jerina, K.L., and Lederich, R.J.: Microstructures and mechanical properties of dispersion-strengthened high-temperature Al-8.5Fe-1.2V-1.7Si alloys produced by atomized melt deposition process. Metall. Trans. A 24, 865 (1993).Google Scholar
Hariprasad, S., Sastry, S.M.L., and Jerina, K.L.: Deformation behavior of a rapidly solidified fine grained Al-8.5%Fe-1.2%V-1.7%Si alloy. Acta Mater. 44(1), 383 (1996).CrossRefGoogle Scholar
Yan, Q.Q., Fu, D.F., Deng, X.F., Zhang, H., and Chen, Z.H.: Tensile deformation behavior of spray-deposited FVS0812 heat-resistant aluminum alloy sheet at elevated temperatures. Mater. Charact. 58, 575 (2007).Google Scholar
Tang, Y.P., Tan, D.Q., Li, W.X., Pan, Z.J., Liu, L., and Hu, W.B.: Preparation of Al–Fe–V–Si alloy by spray co-deposition with added its over-sprayed powders. J. Alloys Compd. 439, 103 (2007).Google Scholar
Wang, F., Zhu, B.H., Xiong, B.Q., Zhang, Y.G., Liu, H.W., and Zhang, R.H.: An investigation on the microstructure and mechanical properties of spray-deposited Al-8.5Fe-1.1V-1.9Si alloy. J. Mater. Process. Technol. 183, 386 (2007).CrossRefGoogle Scholar
Seivastava, A.K., Ojha, S.N., and Ranganathan, S.: Microstructural features and heat flow analysis of atomized and spray-formed Al–Fe–V–Si alloy. Metall. Mater. Trans. A 29A, 2205 (1997).Google Scholar
Rolink, G., Vogt, S., Senčekova, L., Weisheit, A., Poprawe, R., and Palm, M.: Laser metal deposition and selective laser melting of Fe-28 at.% Al. J. Mater. Res. 29(17), 2036 (2014).Google Scholar
Sercombe, T.B. and Schaffer, G.B.: Rapid manufacturing of aluminum components. Science 301(5637), 1225 (2003).Google Scholar
Murr, L.E., Gaytan, S.M., and Ramirez, D.A.: Metal fabrication by additive manufacturing using laser and electron beam melting technologies. J. Mater. Sci. Technol. 28, 1 (2012).CrossRefGoogle Scholar
Jia, Q.B. and Gu, D.D.: Selective laser melting additive manufacturing of TiC/Inconel 718 bulk-form nanocomposites: Densification, microstructure, and performance. J. Mater. Res. 29(17), 1960 (2014).Google Scholar
Louvis, E., Fox, P., and Sutcliffe, C.J.: Selective laser melting of aluminum components. J. Mater. Process. Technol. 211, 275 (2011).Google Scholar
Thijs, L., Kempen, K., Kruth, J.P., and Van Humbeeck, J.: Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder. Acta Mater. 61, 1809 (2013).Google Scholar
Brandl, E., Heckenberger, U., Holzinger, V., and Buchbinder, D.: Additive manufactured AlSi10Mg samples using selective laser melting (SLM): Microstructure, high cycle fatigue, and fracture behavior. Mater. Des. 34, 159 (2012).Google Scholar
Read, N., Wang, W., Essa, K., and Attallah, M.M.: Selective laser melting of AlSi10Mg alloy: Process optimisation and mechanical properties development. Mater. Des. 65, 417 (2015).CrossRefGoogle Scholar
Prashanth, K.G., Scudino, S., Klauss, H.J., Surreddi, K.B., Löber, L., Wang, Z., Chaubey, A.K., Kühn, U., and Eckert, J.: Microstructure and mechanical properties of Al-12Si produced by selective laser melting: Effect of heat treatment. Mater. Sci. Eng., A 590(10), 153 (2014).Google Scholar
Prashanth, K.G., Debalina, B., Wang, Z., Gostin, P.F., Gebert, A., Calin, M., Kühn, U., Kamaraj, M., Scudino, S., and Eckert, J.: Tribological and corrosion properties of Al-12Si produced by selective laser melting. J. Mater. Res. 29(17), 2044 (2014).Google Scholar
Manfredi, D., Calignano, F., Krishnan, M., Canali, R., Ambrosio, E.P., and Atzeni, E.: From powders to dense metal Parts: Characterization of a commercial AlSiMg Alloy processed through direct metal laser sintering. Materials 6(3), 856 (2013).Google Scholar
Wu, X.L.: Microstructural characteristics of TiC-reinforced composite coating produced by laser syntheses. J. Mater. Res. 14, 2704 (1999).Google Scholar
Simchi, A.: Direct laser sintering of metal powders: Mechanism, kinetics and microstructural features. Mater. Sci. Eng., A 428, 148 (2006).CrossRefGoogle Scholar
Murr, L.E., Gaytan, S.M., Ceylan, A., Martinez, E., Martinez, J.L., Hernandez, D.H., Machado, B.I., Ramirez, D.A., Medina, F., Collin, S., and Wicker, R.B.: Characterization of titanium aluminide alloy components fabricated by additive manufacturing using electron beam melting. Acta Mater. 58, 1887 (2010).CrossRefGoogle Scholar
Vrancken, B., Thijs, L., Kruth, J.P., and Van Humbeeck, J.: Microstructure and mechanical properties of a novel β titanium metallic composite by selective laser melting. Acta Mater. 68, 150 (2014).Google Scholar
Simonelli, M., Tse, Y.Y., and Tuck, C.: The formation of α+β microstructure in as-fabricated selective laser melting of Ti–6Al–4V. J. Mater. Res. 29(17), 2028 (2014).CrossRefGoogle Scholar
Amato, K.N., Gaytan, S.M., Murr, L.E., Martinez, E., Shindo, P.W., Hernandez, J., Collins, S., and Medina, F.: Microstructures and mechanical behavior of Inconel 718 fabricated by selective laser melting. Acta Mater. 60, 2229 (2012).Google Scholar
Whitaker, I.R. and McCartney, D.G.: The microstructure of CO2 laser welds in an Al–Fe–V–Si alloy. Mater. Sci. Eng., A 196(1–2), 155 (1995).CrossRefGoogle Scholar
Yaneva, S., Kalkanlı, A., Petrov, K., Petrov, R., Houbaert, I.Y., and Kassabov, S.: Structure development in rapidly solidified Al–Fe–V–Si ribbons. Mater. Sci. Eng., A 373(1–2), 90 (2004).CrossRefGoogle Scholar
Skjerpe, P.: Structure of Al m Fe. Acta Crystallogr., Sect. B 44, 480 (1988).CrossRefGoogle Scholar
Gjonnes, J., Hansen, V., Berg, B.S., Runde, P., Cheng, Y.E., Gjonnes, K., Dorest, D.L., and Gilmore, C.J.: Structure model for the phase Al m Fe derived from three-dimensional electron diffraction intensity data collected by a precession technique. Comparison with convergent-beam diffraction. Acta Crystallogr., Sect. B 44, 480 (1988).Google Scholar
Sahoo, K.L., Das, S.K., and Murty, B.S.: Formation of novel microstructures in conventionally cast Al–Fe–V–Si alloys. Mater. Sci. Eng., A 355(1–2), 193 (2003).Google Scholar
Kalkanli, A. and Angi, S.: Effect of cooling rate on microstructure and high temperature stability of rapid solidified Al–Fe–V–Si alloys. Powder Metall. 42, 359 (1999).CrossRefGoogle Scholar
Sahoo, K.L., Sivaramakrishnan, C.S., and Chakrabarti, A.K.: Solidification characteristics of the Al-8.3Fe-0.8V-0.9Si alloy. Metall. Mater. Trans. A 31(6), 1599 (2000).CrossRefGoogle Scholar
Sahoo, K.L. and Pathak, B.N.: Solidification behaviour, microstructure and mechanical properties of high Fe-containing Al–Si–V alloys. J. Mater. Process. Technol. 209(2), 798 (2009).Google Scholar
Guan, Y.C., Zhou, W., Li, Z.L., and Zheng, H.Y.: Study of the solidification microstructure in AZ91D Mg alloy after laser surface remelting. Appl. Surf. Sci. 255, 8235 (2009).Google Scholar
Wen, S.F., Li, S., Wei, Q.S., Yan, C.Z., Zhang, S., and Shi, Y.S.: Effect of molten pool boundaries on the mechanical properties of selective laser melting parts. J. Mater. Process. Technol. 214, 2660 (2014).Google Scholar
He, Y.Q., Qiao, B., Wang, N., Yang, J.M., Xu, Z.K., Chen, Z.H., and Chen, Z.G.: Thermostability of monolithic and reinforced Al–Fe–V–Si materials. Adv. Compos. Mater. 18, 339 (2009).Google Scholar