Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-24T15:12:33.510Z Has data issue: false hasContentIssue false
  • English
  • Français

Secondary dendrite arm migration caused by temperature gradient zone melting in the directionally solidified Sn–40 at.% Mn peritectic alloy

Published online by Cambridge University Press:  12 April 2013

Peng Peng ,
Xinzhong Li ,
Dongmei Liu ,
Yanqing Su ,
Jingjie Guo  and
Hengzhi Fu
Peng Peng
Affiliation:
Department of Materials Engineering, School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, People’s Republic of China
Xinzhong Li*
Affiliation:
Department of Materials Engineering, School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, People’s Republic of China
Dongmei Liu
Affiliation:
Department of Materials Engineering, School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, People’s Republic of China
Yanqing Su
Affiliation:
Department of Materials Engineering, School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, People’s Republic of China
Jingjie Guo
Affiliation:
Department of Materials Engineering, School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, People’s Republic of China
Hengzhi Fu
Affiliation:
Department of Materials Engineering, School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, People’s Republic of China
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Sn–40 at.% Mn peritectic alloys were directionally solidified at different growth rates (1–100 μm/s) under a steep temperature gradient (40 K/mm). The migration of secondary dendrite arm was observed in this peritectic alloy in which both the primary phase and the peritectic phase are intermetallic compounds with nil solubility. This migration is caused by coupling remelting/solidification at the hot/cold sides of the liquid pool between two adjacent secondary dendrite arms by temperature gradient zone melting. Its novel feature is that the remelting temperature of primary phase is a little higher than the solidification temperature of peritectic phase. Analytical solutions based on the assumption that the solubility of both primary and peritectic phases are nil have been proposed to describe this migration. It has also been found that the migration of secondary dendrite arm is most obvious at intermediate growth rates under steep temperature gradient in the directionally solidified Sn–40 at.% Mn peritectic alloy.

Type
Articles
Information
Journal of Materials Research , Volume 28 , Issue 9 , 14 May 2013 , pp. 1196 - 1202
Copyright
Copyright © Materials Research Society 2013 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Vandyoussefi, M., Kerr, H.W., and Kurz, W.: Two-phase growth in peritectic Fe-Ni alloys. Acta Mater. 48, 2297 (2000).CrossRefGoogle Scholar
Hu, X.W., Yan, H., Chen, W.J., Li, S.M., and Fu, H.Z.: Effect of sample diameter on primary and secondary dendrite arm spacings during directional solidification of Pb-26wt.%Bi hypo-peritectic alloy. Rare Met. 30, 424 (2011).CrossRefGoogle Scholar
Ma, D., Xu, W., Ng, S.C., and Li, Y.: On secondary dendrite arm coarsening in peritectic solidification. Mater. Sci. Eng., A 390, 52 (2005).CrossRefGoogle Scholar
Biswas, K., Hermann, R., Wendrock, H., Priede, J., Gerbeth, G., and Buechner, B.: Effect of melt convection on the secondary dendritic arm spacing in peritectic Nd-Fe-B alloy. J. Alloys Compd. 480, 295 (2009).CrossRefGoogle Scholar
Wang, N. and Wei, B.: Rapid solidification of undercooled Cu-Ge peritectic alloy. Acta Mater. 48, 1931 (2000).CrossRefGoogle Scholar
Trivedi, R. and Park, J.S.: Dynamics of microstructure formation in the two-phase region of peritectic systems. J. Cryst. Growth 235, 572 (2002).CrossRefGoogle Scholar
Boettinger, W.J.: The structure of directionally solidified two-phase Sn-Cd peritectic alloys. Metall. Mater. Trans. A 5, 2023 (1974).CrossRefGoogle Scholar
Li, Y., Ng, S.C., and Jones, H.: Observation of lamellar eutectic-like structure in a Zn-rich Zn-3.37wt%Cu peritectic alloy processed by Bridgman solidification. Scr. Mater. 39, 7 (1998).CrossRefGoogle Scholar
Su, Y.Q., Luo, L.S., Li, X.Z., Guo, J.J., Yang, H.M., and Fu, H.Z.: Well-aligned in situ composites in directionally solidified Fe–Ni peritectic system. Appl. Phys. Lett. 89, 231918 (2006).CrossRefGoogle Scholar
Ma, D., Li, Y., Ng, S.C., and Jones, H.: Unidirectional solidification of Zn-rich Zn-Cu peritectic alloys-II. Microstructural length scales. Acta Mater. 48, 1741 (2000).CrossRefGoogle Scholar
Liu, D.M., Li, X.Z., Su, Y.Q., Peng, P., Guo, J.J., and Fu, H.Z.: Secondary dendrite arm migration caused by temperature gradient zone melting during peritectic solidification. Acta Mater. 60, 2679 (2012).CrossRefGoogle Scholar
Frederiksson, H.: The solidification sequence in an stainless steel, investigated by directional solidification. Metall. Mater. Trans. B 3, 2989 (1972).CrossRefGoogle Scholar
Li, B., Brody, H.D., and Kazimirov, A.: Synchrotron microradiography of temperature gradient zone melting in directional solidification. Metall. Mater. Trans. A 37, 1039 (2006).CrossRefGoogle Scholar
Nguyen Thi, H., Reinhart, G., Buffet, A., Schenkd, T., Mangelinck-Noël, N., Jung, H., Bergeon, N., Billia, B., Härtwig, J., and Baruchel, J.: In situ and real-time analysis of TGZM phenomena by synchrotron X-ray radiography. J. Cryst. Growth 310, 2906 (2008).CrossRefGoogle Scholar
Riedl, R. and Fischmeister, H.F.: Dendrite arm climb by temperature gradient zone melting during solidification of a high-speed tool steel. Metall. Mater. Trans. A 21, 264 (1990).CrossRefGoogle Scholar
Allen, D.J. and Hunt, J.D.: Melting during solidification. Metall. Mater. Trans. A 7, 767 (1976).CrossRefGoogle Scholar
Allen, D.J. and Hunt, J.D.: Temperature gradient zone melting and microsegregation in castings, in Solidification and Casting of Metals, 1st ed., edited by M. Hillert (The Metals Society, London, England, 1979), pp. 39–43.Google Scholar
Pfann, W.G.: Temperature gradient zone melting. Trans. AIME 203, 961 (1955).Google Scholar
Fan, J.L., Li, X.Z., Su, Y.Q., Chen, R.R., Guo, J.J., and Fu, H.Z.: Directional solidification of Ti–49 at.%Al alloy. Appl. Phys. A 105, 239 (2011).CrossRefGoogle Scholar
Liang, J.L., Du, Y., Zhao, Q.Z., Liao, C.Z., Tang, Y.Y., Zeng, L.M., Zhang, W.W., and Xu, H.H.: Determination of the phase equilibria in the Mn-Sn-Zn system at 500°C. Metall. Mater. Trans. A 40, 2909 (2009).CrossRefGoogle Scholar
Stange, M., Fjellvåg, H., Furuseth, S., and Hauback, B.C.: Crystal structure and phase relations for Mn3Sn2 and non-stoichiometric Mn2-xSn. J. Alloys Compd. 259, 140 (1997).CrossRefGoogle Scholar