Hostname: page-component-586b7cd67f-rcrh6 Total loading time: 0 Render date: 2024-11-24T15:08:40.904Z Has data issue: false hasContentIssue false
  • English
  • Français

Blended elemental powder densification of Ti-6Al-4V by hot pressing

Published online by Cambridge University Press:  21 March 2011

Bing Ye ,
Marc R. Matsen  and
David C. Dunand
Bing Ye
Affiliation:
Department of Materials Science and Engineering, Northwestern University, Evanston, Illinois 60208
Marc R. Matsen
Affiliation:
Boeing Research and Technology, The Boeing Company, Seattle, Washington 98124
David C. Dunand*
Affiliation:
Department of Materials Science and Engineering, Northwestern University, Evanston, Illinois 60208
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

The densification kinetics of a blend of unalloyed Ti and Al-40V master alloy powders are measured during uniaxial hot pressing under 3–10 MPa pressure for thermal cycling (860–1020 °C) or isothermal (1020 °C) conditions. Subsequent heat treatment for 4–16 h at 1020 °C results in a homogeneous Ti-6Al-4V microstructure. This process provides a low-cost alternative to hot isostatic pressing of prealloyed Ti-6Al-4V powders.

Keywords

TiPowder MetallurgySuperplasticity
Type
Materials Communications
Information
Journal of Materials Research , Volume 26 , Issue 8 , 28 April 2011 , pp. 965 - 969
Copyright
Copyright © Materials Research Society 2011

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Boyer, R.R.: An overview on the use of titanium in the aerospace industry. Mater. Sci. Eng., A 213, 103 (1996).CrossRefGoogle Scholar
2.Druz, V.A., Moxson, V.S., Chernenkoff, R., Jandeska, W.F. Jr., and Lynn, J.: Blending an elemental approach to volume titanium manufacture. Met. Powder Rep. 61, 16 (2006).CrossRefGoogle Scholar
3.Geetha, M., Singh, A.K., Asokamani, R., and Gogia, A.K.: Ti based biomaterials, the ultimate choice for orthopaedic implants—A review. Prog. Mater. Sci. 54, 397 (2009).CrossRefGoogle Scholar
4.Lutjering, G. and Williams, J.C.: Titanium, 2nd ed. (Springer-Verlag, New York, 2007).Google Scholar
5.Atkinson, H. and Davies, S.: Fundamental aspects of hot isostatic pressing: An overview. Metall. Mater. Trans. A 31, 2981 (2000).CrossRefGoogle Scholar
6.Zhang, K., Mei, J., Wain, N., and Wu, X.: Effect of hot-isostatic-pressing parameters on the microstructure and properties of powder Ti-6Al-4V hot-isostatically-pressed samples. Metall. Mater. Trans. A 41, 1033 (2010).CrossRefGoogle Scholar
7.Ye, B., Matsen, M.R., and Dunand, D.C.: Enhanced densification of Ti-6Al-4V powders by transformation-mismatch plasticity. Acta Mater. 58, 3851 (2010).CrossRefGoogle Scholar
8.Weil, K.S., Hovanski, Y., and Lavender, C.A.: Effects of TiCl4 purity on the sinterability of Armstrong-processed Ti powder. J. Alloys Compd. 473, L39 (2009).CrossRefGoogle Scholar
9.Imam, M.A. and Froes, F.H.: Low cost titanium and developing applications. JOM 62, 17 (2010).CrossRefGoogle Scholar
10.Ivasishin, O.M., Eylon, D., Bondarchuk, V.I., and Savvakin, D.G.: Diffusion during powder metallurgy synthesis of titanium alloys. Diffusion and Diffusional Phase Transformations in Alloys 277, 177 (2008).Google Scholar
11.Liu, Y., Chen, L., Wei, W., Tang, H., Liu, B., and Huang, B.: Improvement of ductility of powder metallurgy titanium alloys by addition of rare earth element. J. Mater. Sci. Technol. 22, 465 (2006).Google Scholar
12.Hagiwara, M. and Emura, S.: Blended elemental P/M synthesis and property evaluation of Ti-1100 alloy. Mater. Sci. Eng. A 352, 85 (2003).CrossRefGoogle Scholar
13.Yang, J. and Hwang, W.: The preparation of TiAl-based intermetallics from elemental powders through a two-step pressureless sintering process. J. Mater. Eng. Perform. 7, 385 (1998).CrossRefGoogle Scholar
14.Schuh, C., Noel, P., and Dunand, D.C.: Enhanced densification of metal powders by transformation-mismatch plasticity. Acta Mater. 48, 1639 (2000).CrossRefGoogle Scholar
15.Ottino, J.M. and Lueptow, R.M.: Material science: On mixing and demixing. Science 319, 912 (2008).CrossRefGoogle ScholarPubMed