Hostname: page-component-cd9895bd7-jn8rn Total loading time: 0 Render date: 2024-12-20T07:18:15.415Z Has data issue: false hasContentIssue false
  • English
  • Français

The structure and control of a turbulent reattaching flow

Published online by Cambridge University Press:  26 April 2006

L. W. Sigurdson
L. W. Sigurdson
Affiliation:
Department of Mechanical Engineering, University of Alberta, Edmonton, Alberta, Canada, T6G 2G8
Get access Rights & Permissions [Opens in a new window]

Abstract

An experimental study was made of the effect of a periodic velocity perturbation on the separation bubble downstream of the sharp-edged blunt face of a circular cylinder aligned coaxially with the free stream. Velocity fluctuations were produced with an acoustic driver located within the cylinder and a small circumferential gap located immediately downstream of the fixed separation line to allow communication with the external flow. The flow could be considerably modified when forced at frequencies lower than the initial Kelvin-Helmholtz frequencies of the free shear layer, and with associated vortex wavelengths comparable to the bubble height. Reattachment length, bubble height, pressure at separation, and average pressure on the face were all reduced. The effects on the large-scale structures were studied using flow photographs obtained by the smoke-wire technique. The forcing increased the entrainment near the leading edge. It was concluded that the final vortex of the shear layer before reattachment is an important element of the flow structure. There are two different instabilities involved: the Kelvin-Helmholtz instability of the free shear layer and the ‘shedding’-type instability of the entire bubble. The former consists of an interaction of the shear layer vorticity with itself, the latter with its images that result because of the presence of a wall. In order to determine the optimum forcing frequency, a method of frequency scaling is proposed which correlates data for a variety of bubbles and supports an analogy with Kármán vortex shedding.

Type
Research Article
Information
Journal of Fluid Mechanics , Volume 298 , 10 September 1995 , pp. 139 - 165
Copyright
© 1995 Cambridge University Press

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Ahuja, K. K., Whhipkey, R. R. & Jones, G. S. 1983 Control of turbulent boundary layer flows by sound. AIAA Paper 83-0726.
Bar-Sever, A. 1989 Separation control on an airfoil by periodic forcing. AIAA J. 27, 820–821.Google Scholar
Bhattacharjee, S., Scheelke, B. & Troutt, T. R. 1986 Modification of vortex interactions in reattaching separated flow. AIAA J. 24, 623–629.Google Scholar
Brocher, E. 1977 Oscillating flows in ducts: a report on Euromech 73. J. Fluid Mech. 79, 113–126.Google Scholar
Brown, G. L. & Roshko, A. 1974 On density effects and large structure in turbulent mixing layers. J. Fluid Mech. 64, 775–816.Google Scholar
Cherry, N. J., Hillier, R. & Latour, M. 1983 The unsteady structure of two-dimensional separated and reattaching flows. J. Wind Engng Indust. Aerodyn. 11, 95–105.Google Scholar
Cherry, N. J., Hillier, R. & Latour, M. E. M. P. 1984 Unsteady measurements in a separated and reattaching flow. J. Flow Mech. 144, 13–46.Google Scholar
Collins, F. G. 1981 Boundary-layer control on wings using sound and leading edge serrations. AIAA J. 19, 129–130.Google Scholar
Collins, F. G. & Zelenevitz, J. 1975 Influence of sound upon separated flow over wings. AIAA J. 13, 408–410.Google Scholar
Corke, T., Koga, D., Drubka, R. & Nagib, H. 1977 A new technique for introducing controlled sheets of streaklines in wind tunnels. IEEE Publication 77-CH 1251-8 AES.
Crow, S. C. & Champagne, F. H. 1971 Orderly structure in jet turbulence. J. Fluid Mech. 48, 151–159.Google Scholar
Eaton, J. K. & Johnston, J. P. 1980 Turbulent flow reattachment: an experimental study of the flow and structure behind a backward-facing step. Thermosciences Div., Dept. of Mech. Engng, Stanford, Rep. MD-39.
Eaton, J. K. & Johnston, J. P. 1981 A review of research on subsonic turbulent flow reattachment. AIAA J. 19, 1093–1100.Google Scholar
Freymuth, P. 1966 On transition in a separated laminar boundary layer. J. Fluid Mech. 25, part 4, 683–704.Google Scholar
Gad-El-Hak, M. 1990 Control of low-speed airfoil aerodynamics. AIAA J. 28, 1537–1552.Google Scholar
Gad-El-Hak, M. Bushnfll, D. M. 1991 Separation control: review. Trans ASME I: J. Fluids Engng 113, 5–30.Google Scholar
Hiller, R. & Cherry, N. J. 1981 The effects of stream turbulence on separation bubbles. J. Wind Engng Indust. Aerodyn. 8, 49–58.Google Scholar
Hsiao, F. B., Liu, C. F. & Shyu, J. Y. 1990 Control of wall-separated flow by internal acoustic excitation. AIAA J. 28, 1440–1446.Google Scholar
Huang, L. S., Maestrello, L. & Bryant, T. D. 1987 Separation control over an airfoil at high angles of attack by sound emanating from the surface. AIAA Paper 87-1261.
K´rm´n, T. von & Rubach, H. 1912, Über den mechanismus des flüssigkeits — und luftwiderstandes. Physik. Z. 13, 49–59.Google Scholar
Kelso, R. M., Lim, T. T. & Perry, A. E. 1993 The effect of forcing on the time-averaged structure of the flow past a surface-mounted bluff plate. J. Wind Engng Indust. Aerodyn. 49, 217–226.Google Scholar
Kiya, M., Mochizuki, O., Ido, Y. & Kosaku, H. 1993a Structure of turbulent leading-edge separation of a blunt circular cylinder and its response to sinusoidal disturbances. J. Wind Engng Indust. Aerodyn. 49, 227–236.Google Scholar
Kiya, M., Mochizuki, O., Ido, Y. & Kosaku, H. 1993b Effects of periodic forcing on a turbulent separation zone of a blunt circular cylinder. Trans. JSME B 59 366–373. (in Japanese).Google Scholar
Kiya, M., Mochizuki, O., Tamura, H., Nozawa, T., Ishikawa, R. & Kushioka, K. 1991a Turbulence properties of an axisymmetric separation-and-reattaching flow. AIAA J. 29, 936–941.Google Scholar
Kiya, M., Mochizuki, O., Tanaka, H. & Tsukasaki T. 1991b Control of a turbulent leading-edge separation bubble. In Separated Flows and Jets (ed. V. V. Kozlov & A. V. Dovgal), pp. 647–656. Springer.
Kiya, M. & Sasaki, K. 1983a Free-stream turbulence effects on a separation bubble. J. Wind Engng Indust. Aerodyn. 14, 375–386.Google Scholar
Kiya, M. & Sasaki, K. 1983b Structure of a turbulent separation bubble. J. Fluid Mech. 137, 83–113.Google Scholar
Kiya, M. & Sasaki, K. 1985 Structure of large-scale vortices and unsteady reverse flow in the reattaching zone of a turbulent separation bubble. J. Fluid Mech. 154, 463–491.Google Scholar
Kiya, M., Sasaki, K. & Arie, M. 1982 Discrete-vortex simulation of a turbulent separation bubble. J. Fluid Mech. 120, 219–244.Google Scholar
Koenig, K. 1978 Interference effects on the drag of bluff bodies in tandem. PhD thesis, Calif. Inst. Technology.
Koenig, K. & Roshko, A. 1985 An experimental study of geometrical effects on the drag and flow field of two bluff bodies separated by a gap. J. Fluid Mech. 156, 167–204.Google Scholar
Koga, D. J., Reisenthel, P. & Nagib, H. M. 1984 Control of separated flowfields using forced unsteadiness. Illinois Inst. Technology Fluids and Heat Transfer Rep. R84-1.
Lane, J. C. & Loehrke, R. I. 1991 Leading edge separation from a blunt plate at low Reynolds number. Trans. ASME I: J. Fluids Engng 102, 494–496.Google Scholar
Levi, E. 1983 A universal Strouhal law. ASCE J. Engng Mech. 109, 718–727.Google Scholar
Mabey, D. G. 1972 Analysis and correlation of data on pressure fluctuations in separated flow. J. Aircraft 9, 642–645.Google Scholar
Miau, J. J., Lee, K. C., Cheng, M. H. & Chou, J. H. 1991 Control of separated flow by a two-dimensional oscillating fence. AIAA J. 29, 1140–1148.Google Scholar
Montividas, R. E., Acharya, M. & Metwally, M. H. 1992 Reactive control of an unsteady separating flow. AIAA J. 30, 1133–1134.Google Scholar
Nishioka, M., Asai, M. & Yoshida, S. 1990 Control of flow separation by acoustic excitation. AIAA J. 28, 1909–1915.Google Scholar
Oster, D. & Wygnanski, I. 1982 The forced mixing layer between parallel streams. J. Fluid Mech. 123, 91–130.Google Scholar
Ota, T. 1975 An axisymmetric separated and reattached flow on a longitudinal blunt circular cylinder. Trans. ASME E: J. App. Mech. June 311–315.Google Scholar
Ota, T. & Motegi, H. 1980 Turbulence measurements in an axisymmetric separated and reattached flow over a longitudinal blunt circular cylinder. Trans. ASME E: J. App. Mech. 47, 1–6.Google Scholar
Parker, R. & Welsh, M. C. 1983 Effects of sound on flow separation from blunt flat plates. Intl J. Heat Fluid Flow 4, 113–127.Google Scholar
Roberts, F. A. 1985 Effects of a periodic disturbance on structure and mixing in turbulent shear layers and wakes. PhD thesis, Aeronautics Dept., Calif. Inst. Technology.
Roos, F. W. & Kegelman, J. T. 1986 Control of coherent structures in reattaching laminar and turbulent shear layers. AIAA J. 24, 1956–1963.Google Scholar
Roshko, A. 1954 A new hodograph for free streamline theory. NACA Tech. Note 3168.
Roshko, A. 1955 One the wake and drag of bluff bodies. J. Aero. Sci. 22, 1, 124–132.Google Scholar
Sasaki, K. & Kiya, M. 1991 Three-dimensional vortex structure in a leading-edge separation bubble at moderate Reynolds numbers. Trans. ASME I: J. Fluids Engng 113, 405–410.Google Scholar
Shimizu, M., Kiya, M., Mochizuki, O. & Ido, Y. 1993 Response of an axisymmetric separation bubble to sinusoidal forcing. Trans. JSME B 59 721–727. (in Japanese).Google Scholar
Sigurdson, L. W. 1986 The structure and control of a turbulent reattaching flow. PhD thesis, Aeronautics Dept., Calif. Inst. Technology.
Sigurdson, L. W. 1995 Techniques for approximating and transition of separation bubbles on blunt-faced cylinders aligned coaxially with the free-stream. AIAA J. (submitted).Google Scholar
Sigurdson, L. W., Cimbala, J. & Roshko, A. 1981 Controlled excitation of a separated flow. Bull. Am. Phys. Soc. 26, 1275.Google Scholar
Sigurdson, L. W. & Roshko, A. 1984 The large-scale structure of a turbulent reattaching flow. Bull. Am. Phys. Soc. 29, 1542.Google Scholar
Sigurdson, L. W. & Roshko, A. R. 1985 Controlled unsteady excitation of a reattaching flow. AIAA Paper 85-0552.
Sigurdson, L. W. & Roshko, A. 1988 The structure and control of a turbulent reattaching flow. In Turbulence Management and Relaminarisation (ed. H. W. Liepmann & R. Narasimha), pp. 497–514. Springer.
Soria, J., Sheridan, M. & Wu, J. 1993 Spatial evolution of the separated shear layer from a square leading-edge flat plate. J. Wind Engng Indust. Aerodyn. 49, 237–246.Google Scholar
Sutton, E. P., Evans, G. P., McGuiness, M. D. & Svehla, K. M. 1981 Influence of wall vibrations on a flow with boundary-layer separation at a convex edge. In Unsteady Turbulent Shear Flows (ed. R. Michel, J. Cousteix & R. Houdeville), pp. 285–293. Springer.
Viets, H. 1979 Coherent structures in time dependent shear flows. In Proc. NATO AGARD Conf. 271 on Turbulent Boundary Layers, Experiments, Theory and Modelling, pp. 5.1–5.14. The Hague, The Netherlands.
Viets, H. & Piatt, M. 1981 Induced unsteady flow in a dump combustor. In Combustion in Reactive Systems (ed. J. R. Bowen, A. K. Oppenheim & R. I. Soloukhin), Progress in Astronautics and Aeronautics, vol. 76, pp. 611–624.
Welsh, M. C. & Gibson, D. C. 1979 Interaction of induced sound with flow past a square leading edged plate in a duct. J. Sound Vib. 67, 501–511.Google Scholar
Winant, C. D. & Browand, F. K. 1974 Vortex pairing: the mechanism of turbulent mixing layer growth at moderate Reynolds number. J. Fluid Mech. 63, 237–255.Google Scholar
Wygnanski, I., Champagne, F. & Marasli, B. 1986 On the large-scale structures in two-dimensional, small-deficit, turbulent wakes. J. Fluid Mech. 168, 31–71.Google Scholar
Zaman, K. B. M. Q. 1992 Effect of acoustic excitation on stalled flows over an airfoil. AIAA J. 30, 1492–1499.Google Scholar
Zaman, K. B. M. Q., Bar-Sever, A. & Mangalam, S. M. 1987 Effect of acoustic excitation on the flow over a low-Re airfoil. J. Fluid Mech. 182, 127–148.Google Scholar