Wireless sensor networks are an increasingly popular tool for monitoring various environmental parameters. They can also be used for monitoring the electromagnetic spectrum. Wireless sensors, due to their small size, typically have simplified radio receivers with reduced sensitivity and use small antennas. As a result, their effective performance area is similarly limited. This is especially important in urban areas where there are various kinds of adverse propagation phenomena related to area coverage. The aim of this paper is to present the phenomena in the wireless sensor networks and propose criteria and methods to optimize their deployment to ensure maximizing the probability of detection of emissions, minimization of unmonitored areas, and to provide the necessary hardware redundancy in the priority areas. Influence of detection parameters, number of sensors and range constraints between sensors on received outcomes are also presented.

In some circumstances, electromagnetic compatibility testing must be performed not in a specialized anechoic chamber, but in an open space. However, typical absorbers used in anechoic chambers to absorb incident radiation and to reduce the amount of rays reflected from the walls and the floor, such as ferrite tiles and graphite cones, are not suitable in an open space. In this work, we present the design and a test for the absorbing material, which can successfully be used in a tent or in a similar light and portable structure. The proposed composite material is flexible, has good absorbing and mechanical properties as well as low reflectivity. As an absorber, the nanocrystalline iron alloy with graphite, mixed with an elastomer was proposed. This material was additionally exposed to the ionizing radiation in the dose of 100 kGy in the radioactive gamma source (60Co). The permittivity, permeability, and the shielding properties of the material have been analyzed as well.

This paper focuses on assessing the limitations in the direction-finding process of radio sources with directional antennas in an urbanized environment, demonstrating how signal source antenna parameters, such as beamwidth and maximum radiation direction affect bearing accuracy in non-line-of-sight conditions. These evaluations are based on simulation studies, which use measurement-tested signal processing procedures. These procedures are based on a multi-elliptical propagation model, the geometry of which is related to the environment by the power delay profile or spectrum. The probability density function of the angle of arrival for different parameters of the transmitting antenna is the simulation result. This characteristic allows assessing the effect of the signal source antenna parameters on bearing error. The obtained results are the basis for practical correction bearing error and these show the possibility of improving the efficiency of the radio source location in the urbanized environment.

This paper illustrates the different possibilities given by additive manufacturing technologies for the creation of passive microwave hardware. The paper more specifically highlights a prototyping scheme where the 3D-printed plastic parts can be used as initial proofs of concept before considering more advanced 3D-printed parts (metal parts, for instance). First, a characterization campaign has been made on common plastics used by a 3D printer using the fused deposition modeling and material jetting (Polyjet©) technologies. The impact of the manufacturing strategy (high-speed or high-accuracy) on the part roughness, as well as on the dielectric material permittivity and loss tangent, has been specifically studied at 10 and 16 GHz. Based on a specifically optimized and deeply explained characterization method, the conductivity of a coating based on silver paint has also been characterized on such plastic parts at 10 and 40 GHz. These plastic materials and coating have been used for the creation of quasi-elliptic and tuning-free bandpass filters centered at 6 and 12 GHz and compared with a similar filter made of stainless steel by selective laser melting. Finally, a compact rectangular TE10 to circular TE01 mode converter also undergoes one prototyping step out of plastic before moving to an advanced part made out of stainless steel. This mode converter, which is made in a single part, is designed to operate from 28 to 36 GHz as a tuning-free final demonstrator.

We present a continuously tunable 52-to-67 GHz push–push dual-core voltage-controlled oscillator (VCO) in a 40 nm bulk complementary metal–oxide–semiconductor (CMOS) technology. The circuit is suitable for 60 GHz frequency-modulated-continuous-wave radar applications requiring a continuously tunable ultra-wide modulation bandwidth. The LC-tank inductor is used to couple the two VCO cores. The fundamental frequency of the VCO can be tuned from 26 to 33.5 GHz, which corresponds to a frequency tuning range of 25%. The second harmonic is extracted in a non-invasive way using a transformer. The primary side acts simultaneously as a second harmonic filter. The VCO achieves in measurement a low phase noise of −91.8 dBc/Hz at 1 MHz offset at 62 GHz and an output power of −20 dBm. The VCO including buffers dissipates in the dual-core operation mode 60 mA from a single 1.1 V supply and consumes a chip area of 0.58 mm2.

This paper proposes a dual notched band ultra-wideband (UWB) bandpass filter (BPF) based on hybrid transition of microstrip and coplanar waveguide (CPW). The CPW in ground plane houses a stepped impedance resonator shorted at ends, and is designed to place its resonant modes within the UWB passband. The microstrips on the top plane are placed some distance apart in a back-to-back manner. The transition of microstrip on top and shorted CPW in the ground is coupled through the dielectric in a broadside manner. The optimized design of the transition develops the basic UWB spectrum with good return/insertion loss and extended stopband. Later, defected ground structure, embedded in CPW, and split ring resonators, coupled to feeding lines are utilized to develop dual sharp passband notches. The simulated data are verified against the experimentally developed prototype. The proposed dual notched UWB-BPF structure measures only 14.6 × 7.3 mm2, thereby justifying its compactness.

A simple closed-form analytical formula is proposed to compute the probe reactance of an equilateral triangular patch antenna. The variation of the probe reactance with the variation of antenna dimension, substrate electrical parameters, and probe location is examined thoroughly. The computed values employing the present model show excellent agreement with experimental and simulation results.

In this paper, the first reported waterproof inkjet-printed dual-band monopole antenna on the flexible organic paper substrate is presented. The antenna, which operates at 900 MHz and 2.4 GHz, is inkjet-printed on commercially available photopaper using conductive silver nano-particle ink. To protect it from ambient humidity, a 1 µm thick Parylene-C layer was deposited on top of the antenna. To verify its waterproof capability, the Parylene-C coated antennas were submerged in distilled water for 48 days, and no significant performance degradation was observed in its performance.

This manuscript deals with the development of a novel configuration of a wide-band single-layer frequency selective surface (FSS) for wide-band rejection applications. The established unit cell is composed of a simple circular ring on the top side of the substrate and a combined conductive element on the backside. Such an inclusion of conductive elements and accurate tuning of their dimensions ends in the rejection of a wide frequency band extended from 6.3 to 16.3 GHz. Moreover, the proposed structure exhibits a stable response against different angles of incidence for both TE and TM polarizations. Detailed simulation and measurement studies are carried out to investigate the performance of the proposed FSS. The obtained results are discussed in depth.

A novel concept of using fractal antenna with metamaterial and slot to achieve multiband operation is investigated. The antenna consists of an L-shaped slot, Sierpinski triangle (used as fractal) as the radiating part and metamaterial circular split ring resonator (SRR) as the ground plane. The introduction of metamaterial in the ground plane makes the antenna operate at 3.3 GHz (middle WiMAX). The etching of Sierpinski triangle and L-shaped slot in the radiating monopole perturbs the surface current distribution; thereby increasing the total current path length which tends the antenna to further operate at 5.5 (upper WiMAX), 7.3 (satellite TV) and 9.9 GHz (X-band), respectively. The extraction of medium parameter of a circular SRR through waveguide medium is discussed in detail. The antenna has a compact dimension of 0.33λ0 × 0.27λ0 × 0.01λ0 = 30 mm × 24.8 mm × 1.6 mm, at a lower frequency of 3.3 GHz. Under simulation, antenna operates at 3.3, 5.5, 7.3 and 9.9 GHz with S11 < −10 dB bandwidth of about 5.9% (3.24–3.44 GHz), 5.6% (5.31–5.62 GHz), 7.3% (6.99–7.52 GHz) and 3.02% (9.78–10.08 GHz), respectively. In measurement, antenna exhibit resonances at 3.1, 5.52, 7.31, 9.72 GHz with S11 < −10 dB bandwidth of about 3.5% (3.04–3.15 GHz), 5.01% (5.44–5.72 GHz), 13.2% (6.76–7.72 GHz) and 5.77% (9.42–9.98 GHz), respectively. Good impedance matching and stable radiation characteristics are observed across the operational bandwidth of the proposed configuration.

This paper proposes, a high gain, Fabry Perot cavity antenna with coplanar waveguide (CPW) fed ultra wide band (UWB) radiating element. The proposed antenna has flat edge arrow shape-based radiating element, which act as a main radiating element and responsible for UWB radiation. This UWB microstrip antenna is parasitically coupled with an array of square parasitic patches (PPs), which act as partially reflective surface. The square patches are fabricated at the bottom of inexpensive FR4 substrate and suspended in the air with the help of dielectric rods at 1.5λ0 height. High gain is obtained by resonating PPs at near close frequencies of 3.8–8.8 GHz UWB, where partially reflective surface gives almost positive reflection phase gradients. Two laboratory prototypes of antenna, one with and another without partially reflective surface are fabricated and tested. Details of the proposed antenna design and role of partially reflective surface in gain enhancement of planar CPW fed UWB antenna are described, and typical experimental results are presented and discussed.

In this paper, the resonant frequencies, quality factors and bandwidths of high Tc superconducting circular microstrip patches in the presence of a dielectric superstrate loading have been studied using Galerkin testing procedure in the Hankel transform domain. The exact Green's function of the grounded dielectric slab is used to derive an electric field integral equation for the unknown current distribution on the circular disc. Thus, surface waves, as well as space wave radiation, are included in the formulation. London's equations and the two-fluid model of Gorter and Casimir are used in the calculation of the complex surface impedance of the superconducting circular disc. Galerkin testing is used in the resolution of the electric field integral equation. Two solutions using two different basis sets to expand the unknown disk currents are developed. The first set of basis functions used is the complete set of transverse magnetic and transverse electric modes of a cylindrical cavity with magnetic side walls. The second set of basis functions used employ Chebyshev polynomials and enforce the current edge condition. The computed values for a wide range of variations of superstrate thickness and dielectric constant are compared with different theoretical and experimental values available in the open literature, showing close agreement. Results are showing that the superstrate parameters should always be kept into account in the design stage of the superconducting microstrip resonators.

In this paper, a metasurface-based aperture-coupled circularly polarized (CP) antenna with wideband and high radiation gain is proposed and analyzed. The proposed antenna is comprised of coplanar waveguide coupling with 4 × 4 corner truncated square patches, which show compact size and low profile. The mechanism of the CP antenna is analyzed theoretically based on the mode analysis and equivalent circuit analysis. The parameters of feeding structure and truncated corner are studied and optimized to achieve wide impedance bandwidth (BW) and axial ratio (AR) BW. Finally, an overall size of 38.8 mm × 38.8 mm × 3.5 mm (0.71λ0 × 0.71λ0 × 0.064λ0 at 5.5 GHz) CP antenna is proposed and fabricated. The simulated results demonstrate that over 41.7% impedance BW (S11 < −10 dB) of 4.55–6.95 GHz and 3 dB AR BW of 5.05–6.15 GHz (fractional BW is about 19.6%) are achieved. In addition, the antenna yielded a broadside CP radiation with a high gain average about 7.5 dBic. Experimental results are in good agreement with the simulated ones.