This paper introduces a tri-band stacked elliptical patch antenna featuring a right-handed circular polarized, designed to operate at the L2, L5, and L1 Global Navigation Satellite System bands. Initially, an elliptic patch is constructed and fed by a probe feed to generate TM110 and TM210 modes at resonance frequencies calculated using Mathieu functions. The probe position is precisely adjusted to excite the quasi-orthogonal mode of TM110 to generate circularly polarized (CP) waves at the L2 and L5 bands. Subsequently, an eye-shaped aperture is engraved into the elliptical patch to enhance the axial ratio (AR) beamwidth in the L2 and L5 bands and stimulate the orthogonal mode of TM210 to produce CP waves at the L1 band. Lastly, a stacked partially elliptical parasitic element is placed beneath the upper slotted elliptical patch to enhance the orthogonality of TM210 surface current versions and thus improve the AR beamwidth at the L1 band. The proposed antenna shows low reflection coefficient values at 1.12–1.33 (L2/L5), and 1.5–1.66 GHz (L1). The AR beamwidths are 133/213∘, 167/163∘, and 36/103∘ at two orthogonal cutplanes at L5, L2, and L1 bands, respectively. The antenna also has decent gains of 6–6.9 dBic across the three bands.

Basically, a 4 × 4 Butler matrix (BM) connected to an antenna array allows to have four beams, each oriented in a specific direction depending on the excitation port. In this paper, an almost continuously steerable beam system based on a conventional 4 × 4 BM with adjustable phase shift is presented and demonstrated. Here, varicap diodes are used instead of an additional phase shifter. Under different bias levels applied to the couplers throughout these varicap diodes, an output variable phase difference was obtained. A prototype of the proposed tunable BM integrated with an antenna array operating at 3.5 GHz was fabricated and tested. The experimental results show a good agreement with those simulated. A reflection and isolation coefficient better than −15 dB over the entire desired frequency band and an amplitude imbalance lower than ±1.5 dB were achieved. The measured radiating beam under different DC biasing can be oriented from ±6° to ±18° when port 1 or 4 is excited and oriented from ±32° to ±43° for ports 2 and 3.

This manuscript presents a novel design for an absorptive bandpass filter for mm-wave applications, specifically the commercial FR2 spectrum. Three bands have been selected to be properly input matched with only one of them being the passband, where the insertion loss is minimized. The proposed approach relies on a multiplexer topology implemented through microstrip lines and on thin-film manufacturing process on alumina to shrink the footprint. Cascades of half-wavelength C-shape open-ended resonators are exploited to create the matched bands and define the filter’s selectivity. The selected passband spans from 26.5 to 28.5 GHz, with a measured maximum insertion loss of 3.05 dB for a −3 dB fractional bandwidth of 7.3%. Two absorptive bands are realized to match signals at 24 and 32.25 GHz. The alumina die footprint is 5500 × 3440 µm2, compatible with immediate integration within a mm-wave lineup.

This article presents an innovative design for a low-profile, high-gain circularly polarized (CP) antenna using a single-layer metasurface (MTS). The proposed design incorporates an MTS layer, comprising a 4 × 4 array of hexagonal-shaped patches, printed on the top layer of the substrate. The bottom layer features a coplanar waveguide-fed slotted ground. Circular polarization and broadside radiation are achieved through the application of characteristic mode analysis (CMA). CMA is employed to simultaneously excite desired modes, aiming for wideband circular polarization and gain enhancement. Experimental results validate the effectiveness of the design, with compact dimensions of 0.67λ0 × 0.67λ0 × 0.04λ0. The measurements demonstrate an impressive impedance bandwidth of 84.3% within the 3.7–9.1 GHz. Additionally, a 3-dB axial ratio bandwidth of 18.6% is observed between 4.96 and 5.98 GHz and 3.74% between 8.38 and 8.7 GHz. The antenna exhibits excellent radiation pattern characteristics, featuring a maximum gain of 10.08 dBi at 7.1 GHz. The radiation pattern is symmetrical with broadside directionality, making the antenna well-suited for sensing applications.

This paper details the design and development of a planar switched beam network using 4 × 4 Butler matrix (BM) over a thin and flexible type biocompatible substrate. Four mils thick liquid crystal polymer (LCP) is used as a substrate here (ϵr = 2.92, tanδ = 0.002). The proposed design is centered at 28 GHz, targeting commercial millimeter-wave applications. Floral-shaped antenna with defective ground structures has been implemented as basic radiating elements. The whole structure is based on microstrip line configuration. The architecture occupies an area of 23.85 × 19.20 mm2 over the LCP substrate. Individual components of the BM are detailed here, followed by a system analysis of the whole integrated structure. The present work also covers the electrical equivalent circuit modeling of the whole beam-forming network. The fabricated prototype offers better than 18 dB return losses at each input port for the desired frequency band with 6 dBi (max.) peak gain and 500 MHz bandwidth around the center frequency. Port-to-port isolation of better than 15 dB is achieved with this topology. Experimental and simulated results are in good agreement in all aspects. A comparative study is also chalked out to highlight the significance of the current research work with respect to alike earlier reported structures.

The mining industry is heavily dependent on energy-intensive processes, such as rock breakage, which leads to significant operational costs. This paper explores microwave-assisted rock breakage as an innovative method to enhance the efficiency of comminution within the mining industry. It introduces a system that employs a Klystron microwave power source with a maximum output of 7.5 MW, using a $\mathrm{TM}_{010}$ single-mode cavity at 3 GHz, to channel energy inside a specially designed rock cavity. The paper emphasizes the importance of designing an efficient microwave cavity for this system, focusing on the cavity’s design and simulation. Through both simulated results (using HFSS software) and experimental observations, the study reveals the promising application of microwave technology in the field of mining. The simulated frequency response of the designed cavity (S11) is −22 dB, it demonstrates significant potential for reducing both energy consumption and associated costs. Additionally, the designed cavity is fabricated from aluminum and filled with polyether ether ketone material. The measured frequency response (S11) of the cavity at 3 GHz is −17 dB.

The electromagnetic scattering problem over a wide incident angle can be rapidly solved by introducing the compressive sensing theory into the method of moments, whose main computational complexity is comprised of two parts: a few calculations of matrix equations and the recovery of original induced currents. To further improve the method, a novel construction scheme of measurement matrix is proposed in this paper. With the help of the measurement matrix, one can obtain a sparse sensing matrix, and consequently the computational cost for recovery can be reduced by at least half. The scheme is described in detail, and the analysis of computational complexity and numerical experiments are provided to demonstrate the effectiveness.

In this paper, the design of a circularly polarized (CP) multiple-input–multiple-output (MIMO) antenna system is presented, utilizing a dielectric resonator (DR). This presented antenna system is subsequently integrated with a multifunctional filter, all meticulously structured on a single substrate. The multifunctional filter operates in three modes: reconfigurable band-pass and band-reject filter as well as all-pass filter. The overall structure works as a tunable filtenna. The designed filtenna is expanded into a two-port MIMO system on a unified substrate, providing strong port isolation below −28.5 dB. The overall dimension of proposed radiator is 180 × 180 × 1.6 mm3. The value of peak gain is 5.19 dBic. By switching the states of PIN diodes, the designed filtenna operates as a sensing and communicating antenna for interweave and underlay cognitive radios (CRs). The proposed antenna supports the CP waves within the working band, i.e., 3.6–4.5 GHz. The simulated results are validated by comparing them with the measured results showing less variation among them. MIMO parameters, including the envelope correlation coefficient and diversity gain, have been calculated for the proposed filtenna, representing its suitability for 5G-CR applications.

In this paper, two second-order electronically tunable bandpass filters are presented. The filters are implemented in microstrip technology using barium–strontium–titanate (BST) varactors and digitally tunable capacitors (DTC) for tuning the frequency response of the bandpass filters. The filter realized using BST varactors has a 35% tuning range from 900 MHz to 1.275 GHz with an insertion loss variation from 3.1 to 2.6 dB. The absolute bandwidth is nearly constant over the entire tuning range, varying from 64 to 72 MHz (around ±5% variation). The filter realized using DTCs also has a 36% tuning range from 850 MHz to 1.225 GHz with an insertion loss variation from 3.1 to 1.5 dB. The absolute bandwidth is constant over the tuning range, varying from 88 to 98 MHz (around ±5% variation). The bandpass filters are tuned using a single control signal. The tunable bandpass filters are proposed for use in reconfigurable radios.

A system-in-package for a wideband digital radar, in D-band, requires broadband, high-gain antennas combined with broadband chip-to-package and package-to-printed circuit board (PCB) interconnects. This paper demonstrates a wideband, low-loss quasi-coaxial signal transition, and a novel electric split ring resonator (eSRR)-based antenna-in-package (AiP) with a modified reflector concept, for improved gain, in embedded wafer level ball grid array (eWLB) technology. A complete chip-to-package-to-PCB interconnect is also demonstrated by combining the quasi-coaxial transition with a chip-to-package interconnect. The quasi-coaxial signal transition has the largest impedance bandwidth among ball grid array-based quasi-coaxial signal transitions. For the modified reflector concept, a horn-shaped cavity is micromachined in the PCB substrate and remetallized with aerosol-jet printing, placing the reflector 0.25λ from the antenna. The antenna gain is improved with up to 5.3 dB. The AiP with the horn-shaped reflector is the single element with the highest gain, in eWLB technology, above 100 GHz.

In this paper, we introduce a compact 6 × 8 channel multiple-input multiple-output frequency-modulated continuous-wave radar system capable of determining the three-dimensional positions of targets despite utilizing a linear virtual array. The compact system, containing two cascaded radar transceiver ICs, has 48 virtual channels. We conduct a direction of arrival estimation with these virtual channels to determine the azimuth angle. To overcome the spatial limitation of the linear array, we use frequency-steered transmit antennas, which vary their main lobe direction during the frequency chirp, allowing the elevation angle to be determined by using a sliding window fast Fourier transform algorithm. In this study, we present the system’s concept along with the associated signal processing. By taking measurements in different scenarios, each with differently placed corner reflectors, we investigate the capability of the system to separate adjacent targets concerning range, azimuth, and elevation. These measurements are additionally employed to point out the design trade-offs inherent to the system.

This paper introduces an innovative conceptual design of a 400 kW solid-state power amplifier (SSPA) station and presents preliminary measurements for the key components. Recent advancements and benefits of solid-state technology have made the prospect of replacing vacuum tubes increasingly appealing. Historically, a significant challenge was the limited output power capacity of individual solid-state transistors, necessitating the integration of numerous units to generate high-power microwave signals in the range of hundreds of kilowatts. However, modern transistors capable of producing over 2 kW of output power have emerged, facilitating this transition. Another weak point was low power efficiency in high-power operating mode. The advanced rugged technology (ART) of solid-state devices enables the utilization of these transistors in nonlinear and switching operating classes, thereby enabling the creation of high-efficiency high-power amplifiers. In this conceptual design, 264 SSPA modules based on ART, each with a power output of 1.6 kW, are combined. The measurements revealed a single SSPA capable of delivering up to 2 kW output power with a power efficiency of 73% at frequency of 352 MHz. Due to the minimal losses during module combination and working SSPA in Class-C operation mode, the power efficiency of the station is expected to closely mirror that of a single module.

This paper outlines an experimental demonstration of an envelope tracking (ET) technique applied to a kilowatt-level single-ended solid-state power amplifier (SSPA), aimed at enhancing the charging efficiency of superconducting radio frequency (SRF) cavities by reducing reflection power while maintaining a high degree of efficiency. The technique is particularly designed for the pulsed operation of the European Spallation Source (ESS) at a nominal frequency of 352 MHz, with a 5% duty cycle and a pulse width of 3.5 ms. The study introduces an optimal charging scheme using a solid-state-based amplifier to maintain high efficiency, allowing for power ramp-up while minimizing reflections from SRF cavities and optimizing SSPA efficiency. A fast envelope tracking power supply (ETPS) system is implemented for the approximately 300 ms charging time required by the SRF cavities at ESS. The ETPS system, demonstrated on a single module as a proof-of-concept with scalability potential to a 400 kW power station, indicates an overall average efficiency of 70% and a 24% energy saving over traditional vacuum-tube based amplifiers. This demonstrates the ET technique’s effectiveness at the kilowatt level for efficient SRF cavity charging with reduced reflection, offering significant efficiency and energy savings.

Frequency-modulated continuous-wave radar systems profit from increasing the absolute bandwidths of the generated frequency chirps to improve range resolution. As the relative bandwidth of SiGe-voltage-controlled oscillators (VCOs) is limited to about 80%, increasing the center frequency fundamentally or via frequency multiplication is the most direct way to increase that absolute bandwidth. However, as some applications require penetration depth, which dramatically decreases with frequency, other solutions are necessary. Therefore, state-of-the-art concepts rely on the down-conversion of generated frequency chirps via two separately stabilized frequency sources. This article implements a novel architecture, offering relative bandwidths of >100% within a single phase-locked loop (PLL). Therefore, two VCOs at different center frequencies are fed into a down-conversion mixer, whose output is directly stabilized via that PLL with one loop filter generating both tuning voltages. Those circuit blocks can be summarized as one equivalent VCO, offering a higher relative bandwidth and a significantly more linear tuning curve. Thereby, a solution to limited relative bandwidths with high VCO gain variation of single VCO synthesizers is offered while substantially reducing the hardware and implementation effort compared to the state-of-the-art.

The surface deformation of the main reflector in a large radio telescope is closely related to its working efficiency, which is important for some astronomical science studies. Here, we present a deep learning-based surface deformation recovery framework using non-interferometric intensity measurements as input. The recurrent convolutional neural network (RCNN) is developed to establish the inverse mapping relationship between the surface deformation of the main reflector and the intensity images at the aperture plane and at a near-field plane. Meanwhile, a physical forward propagation model is adopted to generate a large amount of data for pre-training in a computationally efficient manner. Then, the inverse mapping relationship is adjusted and improved by transfer learning using experimental data, which achieves a 15-fold reduction in the number of training image sets required, which is helpful to facilitate the practical application of deep learning in this field. In addition, the RCNN model can be trained as a denoiser, and it is robust to the axial positioning error of the measuring points. It is also promising to extend this method to the study of adaptive optics.

A novel wideband reflectarray antenna (RA) is designed for 5G millimeter (mm) wave communications in the frequency range of 26.5–36 GHz. The proposed unit cell is constructed using a grid periodicity of 0.52${{\lambda }_0}{ }$ that offers 636° phase change through phase delay lines (PDLs) (${{\theta }_{\text{s}}}$). These PDLs are attached to the outer end of the unit cell comprising semi-circular rings. Bandwidth enhancement is achieved by incorporating a corrugated slot technique and a suitable air gap beneath the substrate. The proposed center-fed reflectarray is composed of 513 elements distributed in a circular aperture (13.46${{\lambda }_0}$). Using mirror-symmetrical distribution of the unit cells, a cross-polarization reduction as low as −50 dB is realized. At 30 GHz, RA has a measured peak gain of 28.2 dBi, a sidelobe level of −14.3 dB, and an aperture efficiency of 31.4%. The prototype antenna is fabricated, and the simulation results are experimentally validated. The measured 1-dB and 3-dB gain bandwidths of the proposed reflectarray antenna are 31.3% and 41.6%, respectively. The proposed broadband reflectarray can be a potential choice for inter-satellite services like inter-satellite networking/satellite positioning and control; fixed satellite services such as GPS satellite synchronization and data direct to home TV; and satellite position fixing.

In the proposed paper, a novel design and realization of a wide-band, oblique angle-insensitive metamaterial absorbers are presented. The absorber is designed to work over a wide range of frequencies, making it suitable for Ku-band applications. To get wide band absorption, a novel SM-shaped design with a square-tooth circular ring resonator structure is designed efficiently. The unit cell structure is designed with a dielectric substrate (FR4) with a thickness of 3.2 mm (0.16λ0), where λ0 is the wavelength of free space. The novel design of this configuration leads to wideband absorption with respect to a conventional absorber. Several physical parameters are also investigated, such as the dielectric constant, permittivity, permeability, impedance, and negative refractive index. The simulation and experimental results show from 13.60 to 16.14 GHz with 99.1% absorption, which is excellent agreement. The analysis of the proposed design indicates that it possesses the remarkable feature of being insensitive to polarization while also exhibiting high absorption even when the angle of incidence varies. For both the simulation and experiment, results are consistent with a frequency range of 13.60–16.14 GHz for normal incidence. Almost perfect absorption works well for solar cells, EM detection, and imaging applications.

In this paper, a novel tunable dual-band bandpass filter (BPF) with independently controlled passbands and constant absolute bandwidth (CABW) is proposed. The CABW passbands of designed dual-band BPF are obtained using manageable electric and magnetic mix coupling. Furthermore, the multiple transmission paths from the input port to the output port are extended for extra transmission zeros, which results in modified selectivity of the proposed dual-band BPF. The tunability and switchability of the developed filter can be implemented by introducing a single bias voltage of varactors for each band. For the tunable dual-band BPF, the simulated results show that the center frequency (CF) of the first passband varies from 2.38 to 2.68 GHz, and the CF of the second passband varies from 3.28 to 3.88 GHz, while 3-dB absolute bandwidths are 101 ± 7 MHz and 98 ± 4 MHz, respectively. Moreover, the two passbands of the filter can also be independently switched by removing the voltage imposed on the varactor CV1 and CV2. The measured results agree well with simulated results, which verify the design theory.

An enhanced wideband tracking method for characteristic modes (CMs) is investigated in this paper. The method consists of three stages, and its core tracking stage (CTS) is based on a classical eigenvector correlation-based algorithm. To decrease the tracking time and eliminate the crossing avoidance (CRA), we append a commonly used eigenvalue filter (EF) as the preprocessing stage and a novel postprocessing stage to the CTS. The proposed postprocessing stage can identify all CRA mode pairs by analyzing their trajectory and correlation characteristics. Subsequently, it can predict corresponding CRA frequencies and correct problematic qualities rapidly. Considering potential variations in eigenvector numbers at consecutive frequency samples caused by the EF, a new execution condition for the adaptive frequency adjustment in the CTS is introduced. Finally, CMs of a conductor plate and a fractal structure are investigated to demonstrate the performance of the proposed method, and the obtained results are discussed.

This paper presents a broadband circularly polarized (CP) antenna array for millimeter-wave applications, and the antenna array has the advantages of wide impedance bandwidth (IBW), novel CP design, and low profile. The antenna unit consists of a two-layer substrate and two pairs of magnetoelectric dipoles. Stepped microstrip lines coupled by rectangular slits form a feeder network for easy integration. The axial ratio bandwidth (ARBW) is extended because a pair of parasitic patches is loaded and an elliptical perturbation is added. The simulation results show that the antenna has an ARBW of 18.6% (26.4–31.9 GHz) and an IBW of 45.5% (20.6–32.7 GHz), with a gain greater than 7.11 dBic in the IBW. To improve the gain of the antenna, a 2 × 2 antenna array is designed, fabricated, and measured. The measured results show that the array has an ARBW of 16.6% (26.42–31.21 GHz), an IBW of 41.6% (22.28–33.97 GHz), a peak gain of 13.89 dBic in the IBW, the cross-polarization levels in the xoz-plane and yoz-plane are above 20 dB, and a radiation efficiency greater than 89%.