Hostname: page-component-cd9895bd7-dzt6s Total loading time: 0 Render date: 2024-12-28T12:38:15.892Z Has data issue: false hasContentIssue false
  • English
  • Français

Design and implementation of 2.5D frequency-selective surface based on substrate-integrated waveguide technology

Published online by Cambridge University Press:  10 January 2019

Krushna Kanth Varikuntla Open the ORCID record for Krushna Kanth Varikuntla [Opens in a new window]  and
Raghavan Singaravelu
Krushna Kanth Varikuntla*
Affiliation:
Department of Electronics and Communication Engineering, National Institute of Technology Tiruchirappalli, Trichy, India
Raghavan Singaravelu
Affiliation:
Department of Electronics and Communication Engineering, National Institute of Technology Tiruchirappalli, Trichy, India
*
Author for correspondence: Krushna Kanth Varikuntla, E-mail: [email protected]
Get access Rights & Permissions [Opens in a new window]

Abstract

In this paper, the patch-type frequency selective surfaces (FSS) based on substrate-integrated waveguide (SIW) technology is proposed to improve the bandwidth (BW) and angular performance. The proposed FSS configuration overcomes the limitations of both conventional 2D and 3D FSS structures. A closely coupled cascaded mechanism is employed to combine two identical FSS elements separated by thin dielectric substrate results in incorporation of SIW technology; hence, named as 2.5D FSS. A derived equivalent circuit model is used to estimate the basic performance of proposed FSS–SIW elements, and the response of analytical expressions has been validated and final design is obtained using full-wave simulations. Two basic FSS elements viz. single square loop and a Jerusalem cross have been investigated to prove the enhancement in their BW and angular stability. The proposed technique evidently improves the BW and angular stability of FSS structures than in its established form. Besides, various important parameters that influence the performance characteristics of reported 2.5D FSSs are also studied. The important observations made on the thickness, as the thickness increases the bandstop FSS, can change to bandpass FSS. Finally, the proposed FSS structure has been fabricated and measured using free space measurement setup, to show the effectiveness of theoretical results. The measured results show good agreement with simulated results at normal and oblique incidence angle.

Keywords

EM field theory and numerical techniquesmicrowave measurementsmodeling and measurementswave propagation and scattering
Type
Research Papers
Information
International Journal of Microwave and Wireless Technologies , Volume 11 , Issue 3 , April 2019 , pp. 255 - 267
Copyright
Copyright © Cambridge University Press and the European Microwave Association 2019 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1]Munk, BA (2000) Frequency Selective Surfaces: Theory and Design. New York: Wiley.Google Scholar
[2]Li, B and Shen, Z (2014) Dual-band bandpass frequency-selective structures with arbitrary band ratios. IEEE Transactions on Antennas and Propagation 62, 5504–5512.Google Scholar
[3]Kartal, M, Golezani, JJ and Doken, B (2017) A triple band frequency selective surface design for GSM systems by utilizing a novel synthetic resonator. IEEE Transactions on Antennas and Propagation 65, 2724–2727.Google Scholar
[4]Ghosh, S and Srivastava, KV (2017) An angularly stable dual-band FSS with closely spaced resonances using miniaturized unit cell. IEEE Microwave and Wireless Components Letters 27, 218–220.Google Scholar
[5]Liu, N, Sheng, XJ and Fan, JJ (2016) A compact miniaturized frequency selective surface with stable resonant frequency. Progress In Electromagnetics Research 62, 17–22.Google Scholar
[6]Chaharmir, MR and Shaker, J (2015) Design of a multilayer X-/Ka-band frequency-selective surface-backed reflect array for satellite applications. IEEE Transactions on Antennas and Propagation 63, 1255–1262.Google Scholar
[7]Oraizi, H and Afsahi, M (2007) Analysis of planar dielectric multilayers as FSS by Transmission Line Transfer Matrix Method (TLTMM). Progress In Electromagnetics Research 74, 217–240.Google Scholar
[8]Li, M and Behdad, N (2013) Wideband true-time-delay microwave lenses based on metallo-dielectric and all-dielectric lowpass frequency selective surfaces. IEEE Transactions on Antennas and Propagation 61, 4109–4119.Google Scholar
[9]Shivnarayan, and Jha, RM (2015) Electromagnetic techniques and design strategies for FSS structure applications [antenna applications corner]. IEEE Transactions on Antennas and Propagation 57, 135–158.Google Scholar
[10]Yang, G, Zhang, T, Li, W and Wu, Q (2010) A novel stable miniaturized frequency selective surface. IEEE Antennas and Wireless Propagation Letters 9, 1018–1021.Google Scholar
[11]Yan, M, Qu, S, Wang, J, Zhang, J, Zhang, A, Xia, S and Wang, W (2014) A novel miniaturized frequency selective surface with stable resonance. IEEE Antennas and Wireless Propagation Letters 13, 639–641.Google Scholar
[12]Munk, BA, Luebbers, R and Mentzer, CA (1971) Breakdown of periodic surfaces at microwave frequencies, ElectroScience Lab., Dept. Elect. Eng., Ohio State Univ., Columbus, OH, Tech. Rep., 1971, 2989–2981.Google Scholar
[13]Liu, CH, Booske, JH and Behdad, N (2014) Investigating failure mechanisms in high-power microwave frequency selective surfaces, IEEE Antennas Propag. Society Int. Symp. (APSURSI), Memphis, TN, USA, 06–11 July 2014.Google Scholar
[14]Lu, ZH, Liu, PG and Huang, XJ (2012) A novel three-dimensional frequency selective structure. IEEE Antennas and Wireless Propagation Letters 11, 588–591.Google Scholar
[15]Lee, IG and Hong, IP (2014) 3D frequency selective surface for stable angle of incidence. Electronics Letters 50, 423–424.Google Scholar
[16]Joardar, K (1995) Comparison of SOI and junction isolation for substrate crosstalk suppression in mixed mode integrated circuits. Electronics Letters 31, 1230–1231.Google Scholar
[17]Luo, GQ, Hong, W, Hao, ZC, Liu, B, Li, WD, Chen, JX, Zhou, HX and Wu, K (2005) Theory and experiment of novel frequency selective surface based on substrate integrated waveguide technology. IEEE Transactions on Antennas and Propagation 53, 4035–4043.Google Scholar
[18]Xu, RR, Zong, ZY, Yang, G and Wu, W (2008) Loaded frequency selective surfaces using substrate integrated waveguide technology. Microwave and Optical Technology Letters 50, 3149–3152.Google Scholar
[19]Luo, GQ, Hong, W, Lai, QH and Sun, LL (2008) Frequency-selective surfaces with two sharp sidebands realised by cascading and shunting substrate integrated waveguide cavities. IET Microwaves, Antennas & Propagation 2, 23–27.Google Scholar
[20]Qi, NN, Gong, SX, Zhang, YJ and Liu, JF (2008) Reducing bandwidth of FSS using substrate integrated waveguide technology. Journal of Electromagnetic Waves and Applications 22, 2087–2096.Google Scholar
[21]Xi, CZ, Hong, W, Wu, K, Hong, JT, Hao, ZC, Chen, JX, Zhou, HX and Zhou, H (2014) Design of a bandwidth-enhanced polarization rotating frequency selective surface. IEEE Transactions on Antennas and Propagation 62, 940–944.Google Scholar
[22]Mollaei, MSM (2017) Narrowband configurable polarization rotator using frequency selective surface based on circular substrate-integrated waveguide cavity. IEEE Antennas and Wireless Propagation Letters 16, 1923–1926.Google Scholar
[23]Winkler, SA, Hong, W, Bozzi, M and Wu, K (2010) Polarization rotating frequency selective surface based on substrate integrated waveguide technology. IEEE Transactions on Antennas and Propagation 58, 1202–1213.Google Scholar
[24]Ferreira, D, Caldeirinha, RFS, Cuiñas, I and Fernandes, TR (2015) Square loop and slot frequency selective surfaces study for equivalent circuit model optimization. IEEE Transactions on Antennas and Propagation 63, 3947–3955.Google Scholar
[25]Langley, RJ and Drinkwater, AJ (1982) Improved empirical model for the Jerusalem cross, in microwaves, optics and antennas. IEE Proceedings H 129, 1–6.Google Scholar
[26]Grover, FW (2004) Inductance Calculations. Dover Publications, New York.Google Scholar
[27]Deslandes, D and Wu, K (2006) Accurate modeling, wave mechanisms, and design considerations of a substrate integrated waveguide. Microwave Theory and Techniques, IEEE Transactions on 54, 2516–2526.Google Scholar
[28]Krushna Kanth, V and Raghavan, S (2018) Ultrathin design and implementation of planar and conformal polarisation rotating frequency selective surface based on SIW technology. IET Microwaves, Antennas & Propagation 12, 1939–1947.Google Scholar