Monte Carlo (MC) simulations of interlayer molecular structure in monolayer hydrates of Na-saturated Wyoming-type montmorillonites and vermiculite were performed. Detailed comparison of the stimulation results with experimental diffraction and thermodynamic data for these clay-water systems indicated good semiquantitative to quantitative agreement. The MC simulations revealed that, in the monolayer hydrate, interlayer water molecules tend to increase their occupation of the midplane as layer charge increases. As the percentage of tetrahedral layer charge increases, water molecules are induced to interact with the siloxane surface O atoms through hydrogen bonding and Na+ counter-ions are induced to form inner-sphere surface complexes. These results suggest the need for careful diffraction experiments on a series of monolayer hydrates of montmorillonite whose layer charge and tetrahedral isomorphic substitution charge vary systematically.

The correlation between illite/smectite (I/S) diagenesis and mean vitrinite reflectance (Ro) data is examined in mudrocks from a hydrocarbon exploration well (geothermal gradient 35°C km−1) from the Great Hungarian Plain of the Pannonian Basin System. The expandability of I/S decreases with depth and there is a change from random to ordered mixed-layering at about 2500 m depth. At this depth Ro is about 0.6%. Comparison of the correlation of expandability and Ro from this study to published data for the Vienna Basin and the Transcarpathian Basin, sub-basins of the Pannonian Basin System, shows that the correlation is systematically different for each sub-basin, according to their thermal histories. In the Vienna Basin (geothermal gradient 25°C km−1), for any given value of Ro, the expandability of I/S is less than in the Transcarpathian Basin (geothermal gradient 55°C km−1) and the sediments are older and more deeply buried. Data from the present study are intermediate. This variation is believed to be due to the effect of time on the smectite-to-illite reaction. Results of an optimization procedure to calculate the kinetics of the smectite-to-illite reaction, using as input the expandability depth profiles, and thermal histories constrained by comparison of observed and calculated Ro data, showed that I/S diagenesis in the Pannonian Basin System can be modelled by a single first order rate equation:

$-dS/dt=e^{log(A)-E/RT}\cdot S$

Novel promising modified clays adsorbents were synthesized by intercalating hydroxy-Al polymer associated with poly(ethyleneoxide) in the interlayer of montmorillonite. Two different PEOs of low molecular weight (600) and high molecular weight (100,000) were used. In both cases, the resulting materials are hydrolytically stable and display a slightly better crystallinity than the materials prepared in the absence of PEO. Thermal analysis and infrared spectroscopy indicate changes in the PEO molecular conformation after intercalation revealing interactions between the polycations and the organic molecules. The chain length of the polymer has a strong influence on the surface area of the pillared materials obtained after calcination at 500°C. The use of the high molecular weight polymer leads to products with a higher specific surface area (about 400 m2/g) whereas the lower molecular weight compound does not modify significantly the surface areas. This behavior can be explained by the different nature of the species intercalated in the interlayer. PEO(600) leads to isolated organometallic species whereas PEO(100,000) seems to lead to a network of complexed polycations linked by ethylene oxide units. In the case of the PEO(100,000), high amounts of polymer in the pillaring solution provoke a partial dissolution of the octahedral layer of the clay.

Diagenetic clay minerals usually occur as heterogeneous assemblages of submicroscopic layers consisting of different structure types such as illite, smectite and chlorite, with variable composition within a given structure type, and with highly variable concentrations of imperfections. The dimensions of mixed-layering, the semi-coherent to coherent nature of the structures across the layering, and compositional heterogeneity occur at a scale well below that of an individual thermodynamic phase. These relations imply that most clays are not distinct minerals or phases, and that assemblages of clays in shales and mudstones are incompatible with the phase rule. Such relations are better evaluated in terms of the formation of metastable materials with each small unit having unique chemical properties, rather than as a small number of stable homogeneous phases. Consequently, treatment of most clay minerals in terms of equilibrium stability with either a thermodynamic or experimental approach is subject to error.

Chemical reactions involving most clay minerals are best understood with kinetic models. These involve a great variety of parameters such as time, fluid/rock ratio, deformation history, nature of starting materials and transformation mechanisms, as well as the variables, such as temperature, pressure and composition, that are commonly used to define equilibrium. Solubility experiments on the stabilities of clay minerals are unlikely to attain equilibrium at low temperatures. Moreover, the activity of soluble species may be controlled by surface equilibria, or by absorbed or exchangeable cations. Interpretations of available experiments on the solubility of illite vs. other mineral assemblages are in violation of Schreinemakers’ rules and indicate lack of equilibrium.

Predictable sequences of clay minerals as a function of temperature are best understood through the Ostwald step rule, in which clay mineral assemblages undergo reactions in response to kinetic factors that represent reaction progress rather than an approach to equilibrium. Currently used clay mineral thermometers (illite crystallinity, smectite/illite reaction, chlorite composition) are not based on equilibrium reactions. Such systems are not accurate thermometers and therefore have questionable utility.

The crystal chemistry of Fe-Si scales deposited from geothermal brines at Salton Sea, California, was studied by powder X-ray diffraction and spectroscopic techniques including infrared, 57Fe Mössbauer, 27Al and 29Si nuclear magnetic resonance (NMR), and Fe and Si K-edge extended X-ray absorption fine structure (EXAFS). Scales precipitated at near 250°C from dissolved ferrous iron and silicic acid are composed of hisingerite. This phase is shown to possess the same local structure as nontronite and is a poorly-crystallized precursor of the ferric smectite. A clear distinction can be made at the local scale between hisingerite and 2-line ferrihydrite because, even in their most disordered states, the former possesses a two-dimensional and the latter a three-dimensional anionic framework. At temperature near 100°C Fe-Si scales are a mix of Al-containing opal and hydrous ferrous silicate, whose local structure resembles minnesotaite and greenalite. This hydrous ferrous silicate is very well ordered at the local scale with an average Fe coordination about Fe atoms of 6 ± 1. The difference in crystallinity between the ferrous and ferric silicate scales was related to variations of growth rates of clay particles precipitated from ferrous and ferric salt solutions. The low crystallinity of the ferric smectite suggests that the oxidation of ferrous iron occurs before polymerization with silica.

The alteration experiments of phlogopite with 0.01 N HCl solution containing 0.1 M NaCl at 50°, 80° and 120°C have been carried out to aid in the understanding of the dissolution process of mica and the formation of secondary phases such as vermiculite and interstratified mica/vermiculite. Twenty milligrams of phlogopite samples were suspended in 20 ml or 100 ml of leaching solution.

In these experiments, the dissolution ofphlogopite occurred incongruently, where the preferential release of K occurred in almost all stages of the alteration reaction. In the 100 ml experiments, the priority in dissolution in the initial stage was in the order; K > Fe > Mg, Al > Si. This supports that phlogopite leaching is controlled by the mineral structure. At 80° and 50°C in the 20 ml experiments, the release of all elements except for K was nearly congruent. At 120°C in the 20 ml experiments, the dissolution was outwardly incongruent, which Fe decreased remarkably after six days and Al was released most slowly compared with all other elements in phlogopite. This is probably due to the precipitation of secondary phases such as aluminum and iron oxides and/or hydroxides.

Vermiculite and R1-type interstratified mica/vermiculite, containing 70 ∼ 50% mica, were formed in the alteration process of phlogopite. The following two processes were confirmed for the formation of interstratified structure: Interstratified structure was formed (1) directly from phlogopite or (2) from vermiculite which was produced earlier from phlogopite by regaining of K from the ambient solution. It may depend on the release rate of K from phlogopite whether mica-vermiculite layer sequences develop or vermiculite-vermiculite sequences do.

Historically, the decarbonation of Mg-Al-CO3 hydrotalcite-like compounds (HTlc) has been thought to occur between 400° and 500°C. The present work demonstrates that when HTlcs having the maximum Al content, Al/(Al + Mg) = 0.33, are heated to 500°C, 20–30% of the carbonates remain. The evolution of the remaining carbonates was observed as two maxima, at 600 and 900°C At these temperatures, Al ions go into MgO, and spinel (MgAl2O4) forms. Therefore, the carbonates are released as the Al ions migrate.

At a lower Al content, Al/(Al + Mg) = 0.25, CO2 evolution is almost complete at 500°C. This HTlc has no maximum of CO2 evolution above 500°C. Lower charge densities, due to lower Al contents, lead to lower amounts of remaining carbonate anions.

Transformation of montmorillonite was experimentally investigated using a model system of montmorillonite-alanine at 100 MPa and up to 500°C. Sodium-montmorillonite changed to a mixed layer mineral of sodium- and ammoniumn-montmorillonites (Na/NH4-Mnt) in the temperature range from 150 to 400°C. Ammonium ions were the decomposition product of alanine above 150°C. The Na/NH4-Mnt transformed to regularly and randomly interstratified minerals of NH4-montmorillonite and NH4-mica (o. NH4-Mnt/NH4-Mic and d. NH4-Mnt/NH4-Mic) at 400°C. These mixed layered minerals transformed to ammonium-mica at 500°C. Ammonium-analcime appeared and coexisted with the smectites at temperatures over 200°C, and with albite for those over 400°C.

In comparison with the results of previous experiments in which there was no organic component, the present results revealed that (1) some uncommon mineral phases appeared by replacement of sodium ions in montmorillonite with ammonium ions, i.e., NH4-Mic, o. and d. NH4-Mnts, o. and d. NH4-Mnt/NH4-Mics, and (2) ammonium-analcime appeared. The mineral assemblages and alteration sequences correspond better with those observed in the natural system than those known from experimental results in aluminosilicate-water system.

The nature and number of acid sites per unit weight on a series of materials obtained by interaction of a montmorillonite with zirconium or cerium hydrogenphosphates precipitated in situ by reaction between their precursors have been investigated.

The quantitative determination of the surface acidity has been carried out by three different methods: titration with triethanolamine in aqueous media; TG analysis of the samples after n-butylamine treatment and vacuum desorption; and chemisorption of NH3 at 239.8 K. Additional information about the nature of the surface acid sites has been obtained from the IR spectra of the samples with bases adsorbed.

Results show that the acid site density on the montmorillonite-cerium or zirconium phosphate cross-linked compounds is greater than on the parent montmorillonite and increases as the content in tetravalent metal phosphate rises throughout the different series. Also the number of acid sites for the cerium phosphate-montmorillonite materials is lower than for zirconium ones and the characteristics obtained depend on the bases used for their evaluation.

The presence of two IR adsorption bands at 1400 and 3145 cm−1, assigned to the NH4+ ion, and the absence of the 1170–1361 cm−1 bands, characteristic of the NH3 adsorbed on a Lewis site, strongly suggest the Brönsted character of the acidity of these compounds.

The effect of cooling rate on the formation of smectite crystals with high crystallinity was investigated using two different types of high-pressure and high-temperature apparatus, a modified belt type and a uniaxial split-sphere type. The cooling rate was changed after a treatment of the sample at 5.5 GPa and 1500°C. Smectite crystals were obtained at faster cooling rate, coexisting with coesite, kyanite, jadeite, corundum and/or glass. In the slowly cooled process, no smectite crystals were obtained but coesite, kyanite, jadeite and clinoenstatite were formed. These results indicate that smectite crystals are formed metastably during the quenching of the high-pressure and high-temperature hydrous silicate melt.

Synthetic aluminum-substituted maghemite samples, γ-(Fe1-xAlx)2O3, have been prepared by thermal decomposition of Al-lepidocrocite (γ-Fe1-xAlxOOH), with × = 0, 0.04, 0.06, 0.14 and 0.18. The particles are needle-shaped and the mean crystallite diameter along the [311] crystallographic direction was found to be between 2.0 and 5.0 nm. Mössbauer spectra were collected at 6 K and from 80 K up to 475 K at steps of 25 K. In a wide range of temperatures the spectra of the non-substituted sample consist of a superposition of a broad sextet and a superparamagnetic doublet, whereas for the Al-maghemites this range is much smaller. From the temperature variation of the fractional doublet area two different parameters were defined: the temperature corresponding to a 50/50 doublet-sextet spectrum (T1/2), and the temperature below which the doublet ceases to exist (T0). These two parameters (T1/2 and T0) decrease from 390 K and 92 K (Al-free sample), to 118 K and 64 K (4 mole % Al) and to 100 K and 48 K (18 mole % Al), respectively. The average hyperfine fields at 6 K undergo a steep drop in going from the Al-free sample (Hhf = 506 kOe) to the sample with 4 mole % Al (Hhf = 498 kOe), but for higher substitutions the effect is much smaller. The A- and B-site quadrupole splittings, obtained from the data between 220 K and 475 K, were found as: ΔEQ,A = 0.86 ± 0.04 mm/s and ΔEQ,B = 0.65 ± 0.04 mm/s for the 4 mole % Al sample. The characteristic Mössbauer temperature, determined from the temperature dependence of the average isomer shift, was found to be in the range of 500–600 K.

A process for treating smectite-bearing rock samples that utilizes LR White resin; allows TEM observation of expanded smectite interlayers and therefore preservation of original rock textures. Examples of several lattice fringe images are shown, including: (1) Dioctahedral smectite layers from a shale (1388.9 meter depth, Texas Gulf Coast) give fringes that consistently have spacings of 1.2–1.3 nm, yet duplicate other features previously observed in collapsed samples. (2) Packets of illite layers give fringes with 1.0-nm spacings coexisting with packets of (dominantly) R1 I/S having 2.1-nm lattice fringe spacings in a Gulf Coast shale from 4742.1 m. (3) Rectorite from Garland Co., Arkansas gives 2.3-nm lattice fringes. Samples with wide ranges of I/S ratios and lithologies have been found to be permanently expanded with retention of original textures, commonly leading to unambiguous identification of illite and smectite interlayers in lattice fringe images.

A laboratory study of the hydraulic conductivity (HC) of a marine clay with monovalent, divalent and trivalent cations revealed large differences in HC. The exchangeable cations employed in this study are Na, K, NH4, Mg, Ca and Al in order of increasing valency. An interpretation of the results derived from consolidation tests suggests that HC is significantly affected by the valency and size of the adsorbed cations. An increase in the valency of the adsorbed cations leads to quicker rates of consolidation and higher HC, while, for a constant valency an increase in the hydrated radius of the adsorbed cations results in a lower rate of consolidation and HC. The reduction in HC was related to the dispersion and deflocculation of clay. Lower valency and higher hydrated radii of the exchangeable cations enable the double layer repulsive forces to predominate, thereby increase dispersion and deflocculation.

A series of natural clays, including 1:1 layer silicates (serpentines, kaolin minerals), smectites, vermiculite, micas, talc, pyrophyllite, sepiolite, and palygorskite, were studied by 19F magic-angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy. The 19F chemical shift in these layer silicates is characteristic of the structure, in particular, to the local octahedral cation occupancy. Fluoride ions bonded to three Mg octahedral cations have a chemical shift of about −177 ppm and those bonded to two Al cations and a vacancy have a chemical shift of about −134 parts per million (ppm). The shift at −182.8 ppm in hectorite is apparently associated with fluoride bonded to two Al cations and a Li cation. Surprisingly, the difference in chemical shift of the interlayer and inner fluoride in 1:1 layer silicates is insufficient to distinguish these sites. Based on trends in chemical shift, it appears that fluoride substitution for inner hydroxyls in clays with octahedral substitution is not random. Fluoride is apparently preferentially associated with Mg rather than Al in the octahedral sheet as no resonance due to a fluoride bonded to two Al cations and a vacancy is observed in clays such as SAz-1.

The vibrational modes of clay minerals are uniquely accessible to FT Raman spectroscopy, but this potentially powerful technique has found limited application to the study of clay mineral structure. Raman spectra in the 50 to 3800 cm−1 region were obtained for a number of kandite clays. The kandite clay minerals are characterised by relatively intense bands centred at 142.7 cm−1 for kaolinite, 143 cm−1 for halloysite and 131.2 cm−1 for dickite with prominent shoulders at 129, 127, and 120 cm−1 respectively. These vibrational modes are attributed to the O-Al-O and O-Si-O symmetric bends. Differences in the lattice modes for the kandite clay minerals in the 200 to 1200 cm−1 were obtained. Four OH bands were obtained for kaolinite 3621, 3652, 3668, and 3695 cm−1; three OH bands were found for a selection of dickites and halloysites. The San Juan Dickite and the Eureka Halloysite show further resolution of the low frequency 3620 cm−1 hydroxyl band. This splitting is attributed to variation in the position of the inner hydroxyls. Variation in band intensity and position was found to be sample dependent.

Tetramethylphosphonium-smectite (TMP-clay) and tetramethylammonium-smectite (TMA-clay), were prepared and characterized as adsorbents for a series of aromatic and chlorinated hydrocarbons. The sorption of benzene, alkylbenzenes, and carbon tetrachloride as vapors and as solutes from water was studied to evaluate the effect of water on adsorption efficiency. Adsorption of organic vapors depended on the N2 BET surface area. TMA-clay was a slightly better adsorbent than TMP-clay, due to its somewhat higher surface area. The Langumir isotherms obtained indicated that adsorption occurred predominantly in the interlayer micropores, apparently on mineral surfaces between onium ions. Adsorption efficiency of both organo-clays decreased, compared to vapor sorptions, in presence of water. Lower sorption was apparently due to shrinkage of the interlayer pore or cavity sizes by hydration of interlayer TMA and TMP cations. Although sorption efficiencies of both organo-clays was reduced in presence of bulk water, the extent of reduction was much less for TMP-clay. Thus, TMP-clay was a better adsorbent than TMA-clay in presence of water, despite its lower surface area, in direct contrast to vapor sorption. The Langumir isotherms indicated interlayer sorption of benzene, alkylbenzenes and carbon tetrachloride from water by TMP-clay. The absence of Langumir isotherms for toluene, ethylbenzene and p-xylene uptake from water by TMA-clay indicated that these bulkier solutes were not adsorbed in the interlayers. These results indicate that hydration of TMA cations causes shrinkage of the interlayer pores to dimensions that exclude these solutes. The lower degree of hydration of TMP cations enables TMP-clay to maintain interlayer pores large enough to accommodate the bulkier alkylbenzenes.

Boron sorption by hydrous Al-oxide was studied as a function of concentration, pH, temperature and in the presence of oxalate and phosphate. For comparison sorption of B was also measured with charcoal as adsorbent.

At constant pH a Langmuir type equation was found to fit the results well at pH values below 7.2 where only boric acid molecules are present in solution. B sorption was dependent on pH with maximum sorption at pH 8.5. Oxalate and phosphate ligands form strong bonds to AI and were found to reduce B sorption. Sorption of boric acid molecules decreased with increasing temperature and the isosteric heat of reaction was 13.8 kJ mol−1. These results indicate that there are two mechanisms of sorption on hydrous Al-oxide, physical sorption of boric acid molecules and ligand exchange (chemisorption) of borate, and both mechanisms are favored onto the oxide.

A new model for the description of the structural disorder in natural kaolinite materials is proposed, based on the stacking of two 1:1 layers and their enantiomorphs, and encompassing previously proposed models. The layers, where randomly stacked along the c axis (using probabilistic functions nested in recursive algorithms), correctly describe the observed powder diffraction patterns of natural kaolinites with any density of structural faults. The proposed model was evaluated using electrostatic energy calculations against earlier models of disorder based on layer shift, layer rotation, statistical occupancy of the Al octahedra, or enantiomorphic layers. The present 4-layer model has a minimum of potential energy with respect to the previous models. As expected, the fully ordered triclinic structure of kaolinite possesses the absolute minimum of potential energy.

Upper Cretaceous-Tertiary marine clayey-calcareous rocks of the Hekimhan basin contain fibrous clay minerals in significant amounts. Ophiolitic rocks in the provenance area have contributed the elements to form the clay minerals. XRD, SEM, major, trace and REE analyses were applied to samples taken from several stratigraphic sections. Diagenetic minerals such as smectite, dolomite, calcite, gypsum, celestite and quartz/chalcedony are associated with sepiolite-palygorskite group clays. Trace and rare earth elements (REE) are more abundant in palygorskite than sepiolite. REE abundances in the sepiolite-palygorskite are characterized by negative Eu and positive Nd anomalies when normalized with respect to chondrite and shale. Sepiolites with sharp XRD peaks are formed by diagenetic replacement of dolomite and diagenetic transformation of palygorskite, or by direct crystallization from solution. The average structural formula of the sepiolite is:

(Mg7.15Al0.13Fe0.31Cr0.06Ni0.04)(Si11.98Al0.02)O30(OH)4(OH2)4Ca0.03Na0.02K0.02.8H2O

Palygorskite appears to be authigenic by direct precipitation from solution. It exists in both monoclinic and orthorhombic forms with the mean structural formula given below

(Mg2.22Al1.00Ti0.04Fe0.77Cr0.01Ni0.02)(Si7.68Al0.32)O20(OH)2(OH2)4Ca0.07Na0.05K0.10.4H2O

Methods previously used to distinguish between water adsorbed on external surfaces and in the interlamellar space of Na-montmorillonite during adsorption and desorption of water vapor have been extended to a set of homoionic Li-, Na-, K-, Rb- and Cs-montmorillonite. The textural and structural features have been investigated at different stages of hydration and dehydration using controlled-rate thermal analysis, nitrogen adsorption volumetry, water adsorption gravimetry, immersion microcalorimetry and X-ray powder diffraction under controlled humidity conditions. During hydration, the size of the quasi-crystals decreases from 33 layers to 8 layers for Na-montmorillonite and from 25 layers to 10 layers for K-montmorillonite, but remains stable around 8–11 layers for Cs-montmorillonite. Each homoionic species leads to a one-layer hydrate, which starts forming at specific values of water vapor relative pressure. Li-, Na- and K-montmorillonite can form a two-layer hydrate. By comparing experimental X-ray diffraction patterns with theoretically simulated ones, the evolution of structural characteristics of montmorillonites during hydration or desorption can be described. Using structural and textural data, it is shown that during adsorption: (1) the rate of filling of interlamellar space of the one layer hydrate increases with the relative pressure but decreases with the size of the cations; and (2) the different hydrated states are never homogeneous.