Alumina-pillared montmorillonite is prepared by intercalation of polyoxyhydroxy aluminum cations (Al137+) of a natural montmorillonite from Dimitrovgrad, Bulgaria. Transmission electron microscopy, powder X-ray diffraction, energy dispersive X-ray spectroscopy, and surface area (BET) methods are used to study the untreated and pillared forms of the montmorillonite. A structural model involving deformed Al13 pillars is proposed. Four pillar types are derived and these pillars are uniformly distributed over the interlayer-cation positions of montmorillonite. Calculated electron diffraction patterns were simulated using the multi-slice method. The structural model explains the increased ordering along the c axis of the pillared form compared with the untreated montmorillonite. The model explains the structure of a pillared montmorillonite with different distributions of the pillars in the interlayer. The proposed model is consistent with the observed data.

KCl-, KBr-, and KI-kaolinite intercalation complexes were synthesized by gradually heating potassium-halide discs of the dimethylsulfoxide (DMSO)-kaolinite intermediate at temperatures to 330°C. Two types of complexes were identified by infrared spectroscopy: almost non-hydrous, obtained during thermal treatment of the DMSO complex; and hydrated, produced by regrinding the disc in air. The former showed basal spacings with integral series of 00l reflections indicating ordered stacking of parallel 1:1 layers. Grinding resulted in delamination and formation of a disordered “card-house” type structure. The frequencies of the kaolinite OH bands show that the strength of the hydrogen bond between the intercalated halide and the inner-surface hydroxyl group decreases as Cl > Br > I. The positions of the H2O bands imply that halide-H2O interaction decreases in the same order. Consequently, the strength of the hydrogen bond between H2O and the oxygen atom plane increases in the opposite sequence.

In the non-hydrous KCl-kaolinite complex the inner hydroxyl band of kaolinite at 3620 cm-1 is replaced by a new feature at 3562 cm-1, indicating that these OH groups are perturbed. It is suggested that Cl ions penetrate through the ditrigonal hole and form hydrogen bonds with the inner OH groups. In contrast, Br and I ions are too large to pass into the ditrigonal holes and do not form hydrogen bonds with the inner hydroxyls.

The adsorption and degradation of the herbicide triasulfuron [2-(2-chloroethoxy)-N-[[(4-methoxy-6-methyl-1,3,5-triazin-2-yl)amino]carbonyl]benzenesulfonamide] (CMMT) on homoionic Fe3+-, Al3+-, Ca2+-, or Na+-exchanged montmorillonite in aqueous medium were studied. Ca- and Na-exchanged montmorillonite were ineffective in the adsorption and degradation of triasulfuron. The adsorption on Fe-and Al-exchanged montmorillonite was rapid, and equilibrium was attained after 5 min. Degradation of the herbicide was slow and the type of the degradation products depended on the nature of the exchangeable cations. In the presence of Fe3+-rich montmorillonite, the metabolites 2-(2-chloro-ethoxy)benzenesulfonamide (CBSA), 2-(2-chloroethoxy)-N-[[(4-hydroxy-6-methyl-1,3,5-triazin-2-yl)amino]carbonyl]benzenesulfonamide (CHMT), and l-[2-(2-chloroethoxy)benzene-l-sulfonyl]-7-acetyl-triuret (CBAT) were the only identified products, whereas 2-amino-4-methoxy-6-methyltriazine (AMMT), CBSA, CHMT, and CBAT were the primary metabolites for the Al3+-rich montmorillonite. A Fourier transform infrared (FT-IR) study of montmorillonite samples after the interaction with triasulfuron in organic solution suggests that the hydrolysis mechanism involves the adsorption of the herbicide on the 2:1 layers.

Illitization of smectite during progressive burial diagenesis occurs differently in sandstone and mudstone, which are interbedded in the sedimentary sequence of the Niigata basin. Reaction progress of illitization of smectite via mixed-layer illite-smectite (I-S) in the mudstone is more complete than in the sandstone. In sandstone, smectite converts to (Reichweit, R ≥ 3) I-S and illite via random (R = 0) I-S to ordered (R = 1) I-S, and authigenic chlorite and quartz form as products of the illitization of smectite.

The original composition of detrital smectite and the occurrence of Na+, K+, Ca2+, Mg2+, and Fe2+ in pore fluids partly control both illitization of smectite and the resulting authigenic mineral products in the diagenetic process. In mudstone, detrital smectite is K- and Si-rich in composition, and the illitization of smectite indicates that the original composition is mostly inherited. Excess silica owing to illitization is released to produce authigenic quartz. In sandstone, smectite forms primarily by precipitation. The evolving compositions produced by early illitization form smectite, then random (R = 0) I-S, and then ordered (R = 1) I-S. These transitions are related to compositions of pore fluid. Changes in K/(K + Ca + Na) vs. K + Ca + Na imply that the increase of interlayer cations occurs by absorption and smectite transforms to random (R = 0) I-S, followed by the exchange of interlayer cations to ordered (R = 1) I-S with increasing diagenetic grade. Late illitization from (R = 1) I-S to R ≥ 3 suggests decomposition of smectite and early I-S with an increase in the number of illite layers. Dissolution experiments of host rocks with pure water and 0.01 M HCl solution reflect the differences in chemistry of the original pore fluid and authigenic carbonate in the process of diagenesis of clastic rocks. These results explain how chemical composition produces large variations in transformation temperature of smectite to illite in the diagenetic process.

Sorptive properties of organoclays may be greatly influenced by the physicochemical properties of organic sorbates. Hexadecyltrimethylammonium(HDTMA) clays were prepared using a high-charge smectite (HDTMA-SAz-1), a low-charge smectite (HDTMA-SWy-2), and an illite (HDTMA-ILL). The resultant organoclays were used to sorb aqueous phase 1,2-dichlorobenzene (o-DCB), 1,3-dichlorobenzene (m-DCB), and 1,4-dichlorobenzene (p-DCB). Sorptive characteristics of these compounds were determined by their molecular polarities (o-DCB > m-DCB > p-DCB) and the HDTMA-clay interlayer distance. HDTMA-ILL was used for comparison to HDTMA-SAz-1 and HDTMA-SWy-2. All dichlorobenzene isomers were directly intercalated in the interlayers of HDTMA-SAz-1, causing interlayer expansion. o-DCB and m-DCB were not intercalated in the interlayers of HDTMA-SWy-2 at low concentrations, but intercalation occurred at higher concentrations, which caused interlayer expansion. The concentration needed to produce interlayer expansion depended on the solute molecular polarity, hence a higher concentration of m-DCB than o-DCB was required. p-DCB was sorbed primarily by the HDTMA phase on the external surfaces of HDTMA-SWy-2. In the presence of chlorobenzene (CB), p-DCB sorption by HDTMA-SWy-2 is greatly enhanced, owing to the interlayer expansion by CB and a cosolvent effect. Sorption of o-DCB resulted from both direct solvation-type interactions with HDTMA and partitioning into HDTMA. Such sorption results in double-sigmoid isotherms. m-DCB weakly solvates the HDTMA and partitions into the HDTMA, displaying either a double-sigmoid or a type-III isotherm depending on clay type. p-DCB lacks ability to solvate HDTMA and partitions into HDTMA as its sole mechanism, producing type-III isotherms. HDTMA-clays are potentially effective for treating dichlorobenzene-contaminated wastewater.

The distribution and chemical state of Si in a synthetic 2-line ferrihydrite with a Si/(Si + Fe) molar ratio of 0.11 was studied. Heat treatment under oxidizing conditions shows that Si-rich ferrihydrite is stable to 400°C. The transformation to hematite and the formation of a polymerized amorphous-silica phase occur at 850°C. At this temperature, the specific surface area decreases greatly and the average pore diameter increases, which is indicative of sintering. Heating under severe reducing conditions causes a segregation of Si from Fe and results in a mixture of elemental Fe and SiO2. Surface and structural data suggest that Si is located near the particle surface where it limits the rearrangement of Fe octahedra to form hematite.

X-ray phase analysis of clays is difficult because these materials generally consist of a mixture of different phases, i.e., mixed-layer minerals, individual clay minerals (non mixed-layer), and associated minerals, such as calcite and quartz. The analysis requires knowledge that presently is incorporated in a computer-based expert system. This expert system is capable of a) identification of associated minerals; b) identification of individual clay minerals; c) identification of the nature of the mixed-layer minerals; d) approximate structural characterization of the mixed-layer minerals; and e) precise structural determination of the mixed-layer minerals by comparison of experimental X-ray diffraction (XRD) patterns with calculated patterns for different models. Accuracy of the conclusions drawn by the expert system has been verified with literature data. Programs for the structural characterization of mixed-layer minerals must allow a) modification of the structural characteristics, abundances, and order-disorder distribution of the layers; b) modification of the distribution of the sizes of coherent scattering domains; and c) consideration of mixed-layer clays with more than two components. Two programs were written to calculate the XRD patterns of two- and three-component mixed-layer minerals consisting of any layer type and without any limitation in the order-disorder relationships.

The intercalation complex of a low-defect (“well-crystallized”) kaolinite from Cornwall, England, with hydrazine was studied by high-temperature X-ray diffraction (HTXRD), differential thermal analysis (DTA), and thermogravimetry (TG). The X-ray pattern at room temperature indicated that intercalation of hydrazine into kaolinite causes an increase of the basal spacing from 7.14 to 10.4 Å, as previously reported. Heating between 25-200°C produces a structural rearrangement of the complex, which initially causes a contraction of the basal spacing from 10.4 to 9.6 Å. In a second stage, the basal spacing reduces to 8.5 Å. Finally, in a third stage, a reduction in spacing occurs through a set of intermediate phases, interpreted as interstratifications of intercalated and non-intercalated 1:1 layers. Evidence for these changes was observed by DTA, where three endothermic reactions are observed at low temperature. This behavior suggests that intercalated molecules occupy several well-defined sites in the interlayer of the kaolinite complex. The intercalated molecules deintercalate in an ordered fashion, which explains the successive and discontinuous contraction of the basal spacing of the complex. Heating between 200-400°C caused a limited increase in stacking order of the kaolinite structure, whereas dehydroxylation of kaolinite and the disappearance of its X-ray reflections occurred between 450-640°C.

The Mössbauer and infrared spectra of Li- and Rb-saturated nontronites from Washington, USA (SWa-1), heat treated at different temperatures, were measured. The Mössbauer results show that diffusion of Li+ into the 2:1 layer by heat treatment at 250-300°C does not affect the magnetic hyperfine interactions of the octahedral iron centers. In contrast, significant changes were observed by calcination at temperatures >300°C for Li-saturated nontronites. The main features of the Mössbauer spectra recorded at different temperatures reveal superparamagnetic behavior with a blocking temperature of ~5 K. The superparamagnetic behavior is related to small magnetic domains created by partially broken Fe-O-Fe bonds upon heat treatment. The infrared spectra of Li-rich nontronite, heat treated at 300°C, show changes attributed to Li migration into the hexagonal cavities. Heating to higher temperatures, produced changes in the spectra of the Li- and Rb-saturated nontronites owing to the dehydroxylation of the layer structure. The dehydroxylation process begins with the loss of OH groups in the FeOHFe bridges and is completed with the disruption of the Al-O bonds at >600°C.

The dielectric behavior of kaolinite, montmorillonite, allophane, and imogolite samples adjusted to a water potential of 33 kPa was examined using a time-domain reflectometry method over a wide frequency range of 103-1010 Hz. A dielectric relaxation peak owing to bound H2O was observed. The observation of this peak required the precise determination of the contributions of dc conductivity. The peak is located at 10 MHz, indicating that the relaxation time of the bound H2O is approximately ten times longer than the relaxation time of bound H2O with organic polymers, such as an aqueous globular-protein solution. The structure of bound H2O differs between phyllosilicates and amorphous phases, based on differences in relaxation strength and the pattern of distribution of the relaxation times. The dielectric process involving rotation of bulk H2O molecules was also observed at 20 GHz. The relaxation strength of bulk H2O increased with an increase in the water content. The interfacial polarization in the diffuse double layer occurred only in montmorillonite and kaolinite, indicating that mechanisms involving the Maxwell-Wagner and surface-polarization effects cannot be extended to include allophane and imogolite. Although these results suggest that additional work is required, a tentative conclusion is that a tangential migration of counter-ions along clay surfaces may be important.

OH-A1 solutions were prepared by adding appropriate amounts of NaOH to A1C13 to obtain OH/Al mole ratios of 2.0, 2.5, 2.7, 3.0, and 3.3 in the final suspension. Solid Na2SO4 and Georgia kaolinite (KGa-2) were added individually and jointly to the OH-Al solutions. All samples were aged for 30, 70, and 180 d. X-ray diffraction, infrared spectroscopy, scanning electron microscopy, and energy dispersive X-ray spectrometry were used to characterize precipitates. Bayerite, gibbsite, and nordstrandite crystallized at mole ratios of 3.0 and 3.3, with bayerite being the most abundant. A morphology of clusters of triangular pyramids is described for bayerite. Despite the aging duration, only noncrystalline Al compounds were obtained in mole ratios of 2.0, 2.5, or 2.7. The addition of sulfate to OH-A1 solutions in mole ratios of 2.0 and 2.5 produced crystalline basic aluminum sulfates of variable morphology, but with similar chemical compositions. These phases lost crystallinity with aging. The product from a 2.7 OH-Al solution was X-ray amorphous hydroxysulfate. In contrast, products obtained at mole ratios of 3.0 and 3.3 contained no sulfate ion, which restricted the formation of gibbsite, bayerite, and nordstrandite. The addition of kaolinite to the solutions in OH/A1 mole ratios of 3.0 and 3.3 favored the formation of nordstrandite. The simultaneous addition of sulfate and kaolinite to the OH-A1 solutions in mole ratios of 2.0 and 2.5 produced prevalent sulfate over kaolinite, whereas the opposite occurred at mole ratios 3.0 and 3.3.

X-ray diffraction (XRD), Rb-Sr isotope analysis, transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS), and Fourier transform infrared (FTIR) methods were used to study diagenetic illite and illite-smectite (I-S) in Lower Cambrian unlithified clays of shallow depth of burial in the northern part of the intercratonic Baltic paleosedimentary basin of the East-European Platform. The studies focused on the <0.06-µm size fraction of the clay. This fraction consists of a highly illitic illite-smectite (I-S) and a poorly crystalline illite (PCI), with some traces of Fe-rich chlorite also present. Rb-Sr isotopic data for the <0.06-µm size fractions suggest that the illitic I-S and PCI have different formation ages. No precise isotopic ages were derived directly owing to the composite illite mineralogy and retention of radiogenic Sr. This retention occurred because of imperfect isotopic homog-enization at low water/rock ratios. The age of burial diagenesis is proposed to coincide with the time of maximum burial depth, which was achieved during the Middle to Late Devonian and continued until Permian-Triassic erosion. Because of the shallow depth of burial (<2 km), diagenesis was probably a low-temperature (<50°C) transformation process. The resident time of 100–150 million years at maximum burial had a major influence in the process.

The composition of clinoptilolite formed from volcanic glass was investigated from cuttings collected from the offshore MITI-Somaoki borehole, 52 km east of Soma City, Japan. Unaltered volcanic glass and clinoptilolite-replaced glass were found coexisting in the same silicic tuff at 1000 m depth, but unaltered volcanic glass and clinoptilolite did not coexist in individual glass shards, and each material analyzed in this study was pure. The SiO2 and Al2O3 contents of the pure clinoptilolite and the pure, unaltered glass were 69.32 and 13.05 wt. %, and 70.03 and 11.54 wt. %, respectively. The SiO2 content was almost the same and the Al2O3 content was greater in the clinoptilolite-replaced glass compared with the unaltered volcanic glass. As a result, the SiO2/Al2O3 ratio in the clinoptilolite-replaced glass (SiO2/ A12O3 = 5.31) was slightly lower than that of the unaltered volcanic glass (SiO2/Al2O3 = 6.07). The extra-framework cation composition of the clinoptilolite-replaced glass was three times richer in K (K2O = 7.84 wt. %) than the unaltered volcanic glass (K2O = 2.59 wt. %). The cation selectivity of clinoptilolite, which shows a preference for K to Ca and Na, played an important role in the concentration of K in clinoptilolite during clinoptilolite formation from volcanic glass, although the initial pore waters and the volcanic glass were not especially relative K.

Clinoptilolite-replaced glass in the calcite-cemented tuff at 1100 m depth was not enriched in Ca, suggesting that the exchangable-cation composition of clinoptilolite did not change by exposure to Ca-rich solutions at this depth. Apparently, the exchangable-cation composition of clinoptilolite, once formed, is relatively stable and difficult to change, even under conditions in which calcite is precipitating on clinoptilolite crystals.

High-resolution transmission electron microscopy (HRTEM), selected-area electron diffraction (SAED), annular dark-field scanning transmission electron microscope (STEM) images, and electron nano-diffraction were used to examine structures of synthetic 2- and 6-line ferrihydrite specimens. HRTEM images of 2-line ferrihydrite (2LFh) show scattered small (~1-3 nm) areas with lattice fringes surrounded by areas free of fringes. All SAED patterns show two bright rings corresponding to d-values of ~0.15 and 0.25 nm; each ring has a conspicuous shoulder on each side. Faint rings corresponding to d-values of 0.08, 0.095, 0.100, 0.106-0.114 (very broad ring), and 0.122 nm are visible in strongly exposed SAED patterns. Nanodiffraction patterns show conspicuous streaks and a lack of superlattice formation.

HRTEM images of 6-line ferrihydrite (6LFh) display larger crystallites (typically ~5-6 nm) with lattice fringes visible in many thin areas. SAED patterns show rings corresponding to d-values of 0.148, 0.156, 0.176, 0.202, 0.227, and 0.25-0.26 nm and a shoulder extending between d-values of ~0.25 and 0.32 nm. Faint rings corresponding to d-values of 0.086, 0.093, 0.107, 0.112, 0.119, 0.125, and 0.135 nm are visible in strongly exposed SAED patterns. Small quantities of hematite, magnetite or maghemite, and an acicular material tentatively identified as goethite were observed in the 6-line ferrihydrite, but these quantities do not contribute significantly to the overall diffracted intensity from the sample.

An environmental infrared microbalance (EIRM) cell was used to study H2O sorption on two montmorillonite samples as a function of water content and type of exchangeable cation. The vibrational spectra showed that H2O sorbed to the clay at low-water content was strongly influenced by the exchangeable cation and by the close proximity to the clay surface. At water contents <6 H20 molecules per exchangeable cation, the H-O-H bending mode of H2O (v2 mode) shifts to a lower frequency and is characterized by an increase in molar absorptivity. In contrast, the positions of the asymmetric and symmetric OH-stretching modes of sorbed water (v1 and v3 modes) shift to higher energies. These observations indicate that H2O molecules sorbed to the clay surface at low-water content are less hydrogen bonded than in bulk H2O. In addition, the vibrational-stretching and bending bands of the structural OH groups of the 2:1 layer are also strongly influenced by H2O content and type of exchangeable cation. By using the EIRM cell, the molar absorptivities of the structural OH-bending vibrations were measured as a function of H2O content. The position and molar absorptivity of the structural OH-bending bands at 920, 883, and 840 cm-1 are strongly influenced by H2O content and type of exchangeable cation. The molar absorptivity of the 920-cm-1 band, which is assigned to the AlAlOH group, decreased strongly at low-H2O content. This reduction in intensity is assigned to a dehydration-induced change in orientation of the structural OH groups resulting from the penetration of H2O molecules into siloxane ditrigonal cavities that are not associated with a net negative charge from isomorphous substitutions.

The oxidation state of structural Fe greatly alters surface chemistry, which may have a large influence on clay-organic interactions. The effect of structural-iron oxidation state on chlorinated hydrocarbons at the clay-water interface was examined. Pentachloroethane (5CA) was reacted with oxidized, reduced, and reoxidized forms of three different smectites: montmorillonite, ferruginous smectite, and nontronite in aqueous suspension under controlled-atmosphere conditions. Pentachloroethane was found to adsorb at different rates for the three smectites. A series of 5CA-adsorption rate constants in the presence of these clays showed a strong correlation with the Fe(II) content of the clay (r2 = 0.98). The clay surface behaves as a Brønsted base and promotes 5CA dehydrochlorination. The adsorption kinetics at the clay-water interface were described by the formation of a precursor complex prior to 5CA dehydrochlorination.