This paper presents performance analyses of the model-scale ERICA and TILTAERO tiltrotors and of the full-scale XV-15 rotor with high-fidelity computational fluids dynamics. For the ERICA tiltrotor, the overall effect of the blades on the fuselage was well captured, as demonstrated by analysing surface pressure measurements. However, there was no available experimental data for the blade aerodynamic loads. A comparison of computed rotor loads with experiments was instead possible for the XV-15 rotor, where CFD results predicted the FoM within 1.05%. The method was also able to capture the differences in performance between hover and propeller modes. Good agreement was also found for the TILTAERO loads. The overall agreement with the experimental data and theory for the considered cases demonstrates the capability of the present CFD method to accurately predict tiltrotor flows. In a second part of this work, the validated method is used for blade shape optimisation.

This paper presents aerodynamic optimisation of tiltrotor blades with high-fidelity computational fluid dynamics. The employed optimisation framework is based on a quasi-Newton method, and the required high-fidelity flow gradients were computed using a discrete adjoint solver. Single-point optimisations were first performed to highlight the contrasting requirements of the helicopter and aeroplane flight regimes. It is then shown how a trade-off blade design can be obtained using a multi-point optimisation strategy. The parametrisation of the blade shape allowed the twist and chord distributions to be modified and a swept tip to be introduced. The work shows how these main blade shape parameters influence the optimal performance of the tiltrotor in helicopter and aeroplane modes, and how an optimised blade shape can increase the overall tiltrotor performance. Moreover, in all the presented cases, the accuracy of the adjoint gradients resulted in a small number of flow evaluations for finding the optimal solution, thus indicating gradient-based optimisation as a viable tool for modern tiltrotor design.

For performance improvement and noise reduction, swept and anhedral tips have been incorporated in advanced-geometry rotor blades. While there are aerodynamic benefits to these advanced tip geometries, they come at the cost of complicated structural design and weight penalties. The effect of these tip shapes on loads, vibration and aeroelastic response are also unclear. In this study, a comprehensive helicopter aeroelastic analysis which includes rotor-fuselage coupling shall be described and the analysis results for rotor blades with straight tip, tip sweep and tip anhedral shall be presented and compared. The helicopter modelled is a conventional one with a hingeless single main rotor and single tail rotor. The blade undergoes flap, lag, torsion and axial deformations. Tip sweep, pretwist, precone, predroop, torque offset and root offset are included in the model. Aerodynamic model includes Peters-He dynamic wake theory for inflow and the modified ONERA dynamic stall theory for airloads calculations. The complete 6-dof nonlinear equilibrium equations of the fuselage are solved for analysing any general flight condition. Response to pilot control inputs is determined by integrating the full set of nonlinear equations of motion with respect to time. The effects of tip sweep and tip anhedral on structural dynamics, trim characteristics and vehicle response to pilot inputs are presented. It is shown that for blades with tip sweep and tip anhedral/dihedral, the 1/rev harmonics of the root loads reduce while the 4/rev harmonics of the hub loads increase in magnitude. Tip dihedral is shown to induce a reversal of yaw rate for lateral and longitudinal cyclic input.

Flow separation followed by aerodynamic stall limits the operation of aircraft. Expanding the flight envelope of aircraft has been a goal of aerodynamicists for decades. This work presents findings from tests in the Oregon State University wind tunnel investigating the effectiveness of a passively actuated suction-surface flap on membrane wings. Experiments were conducted on a rigid plate and membrane wings with and without a pop-up flap. All wings had an aspect ratio of 2, while membrane pre-strain and Reynolds number were varied. An increase in lift at stall was observed for all testing conditions with flap deployment. The observed average increase in maximum lift varied from 5% to 15% for different test conditions. The variation in flap effectiveness is compared to membrane pre-strain, Reynolds number, and wing camber. A quadratic relationship between modelled camber and flap effectiveness is observed, and an optimal level of membrane camber is found to maximise flap effectiveness.

Air Traffic Management (ATM) research generally focuses on achieving a safer, more effective and economical air traffic system. The current airspace system has become increasingly strained as the demand for air travel has steadily grown. Innovative, proactive and multi-disciplinary approaches to research are needed to solve flight congestion and delays as a consequence of this rapid growth. As a result of this growth, air traffic flow becomes more complex, especially in Terminal Airspaces (TMA) where climb and descent manoeuvres of departing and arriving flights take place around airports. As air traffic demand exceeds the capacity in a TMA, the resultant congestion leads to delays that spread all over the system. Therefore, the reduction of delays is critical for airspace designers to increase customer satisfaction and the perception of service quality. Numerous studies have been conducted to reduce delays within TMAs. This research focuses on defining the causes of delays quantitatively through statistical analysis. The first step was to create a fast-time simulation model of sample airspace for collecting delay data. After building up this model using the SIMMOD fast-time ATM simulation tool, simulation experiments were run to produce various traffic scenarios and to generate traffic delay data. The number of airports, entry points, fixes and flight operations in airspace and the probability of wide-body aircraft were considered as independent variables. The correlations between the considered variables were analysed, and the total delay data was modelled using a linear regression model. The findings of regression model present a statistical approach for airspace designers and air traffic flow planners.

This paper develops a method to determine the lift-drag ratio of air cushion craft and specifically the maximum value of the lift-drag ratio, its associated design speed, and related performance and economic measures. The method works from well-established equations for drag and power for air cushion craft. Such values are required to determine the performance and economic efficiency of the craft in many modes of operation. The method covers both amphibious and non-amphibious craft of the types used in both military and commercial operation. A basis is developed for an optimisation procedure to design future craft for maximum efficiency.

This paper deals with the development of a simulation platform for the dynamic analysis of systems characterised by different physical domains. The research has been carried out in the context of the EC-funded Clean Sky Joint Technology Initiative (Green Regional Aircraft/All-Electric Aircraft domain). In particular, the objective of the research is focused on the on-board systems of new All-Electric Aircraft, where a crucial design point is related to the electrical energy management. In the “all-electric” concept, where pneumatic and hydraulic power systems are eliminated to improve aviation costs and environmental impact, the dynamics of electrical power absorptions is to be characterised and managed to avoid excessive peaks with respect to generators capabilities. The paper describes the architecture of a Matlab/Simulink simulation platform developed in order to design and validate of the electrical energy management logics, which lead up to 32% reduction of the maximum power request for the case study considered. Thanks to an approach based on a mixing of co-simulation and S-function compiling, the platform integrates models coming from different environments (AMESim, Dymola/Modelica), and developed by various partners/specialists.