In this paper, fire and evacuation computer simulations are used to reconstruct the 1985 Manchester Airport B737 fire that resulted in the loss of 55 lives. First the actual fire and evacuation are reconstructed. Secondly, the impact of exit opening times and external wind on the fire and evacuation are investigated. Finally, the potential benefit offered by modern materials is evaluated. The results suggest that the number of fatalities could have been reduced by 87% had the forward right exit not malfunctioned and by 36% had the right over-wing exit been opened without delay. Furthermore, given the fuel pool size and location, a critical wind speed of 1.5m/s is necessary to cause the fire plume to lean onto the fuselage eventually resulting in fuselage burn-through. Finally, it is suggested that the use of modern cabin materials could have made a significant difference to the fire development and survivability.

The paper presents the aerodynamic characterization of a low-speed unmanned aerial vehicle, with cropped delta planform and rectangular cross section, at and around high angles-of-attack using flight test methods. Since the linear models used for identification from flight data at low and moderate angles of attack become unsuitable for accurate parameter estimation at high angles of attack, a non-linear aerodynamic model has to be considered. Therefore, the Kirchhoff's flow separation model was used to incorporate the non-linearity in the aerodynamic model in terms of flow separation point and stall characteristic parameters. The Maximum Likelihood (ML) and Neural Gauss-Newton (NGN) methods were used to perform the parameter estimation on one set of low angle-of-attack and one set of near-stall flight data. It is evident from the estimates that the NGN method, which does not involve solving equations of motion, performs on a par with the classical ML method. This may be attributed to the reason that NGN method uses a neural network which has been trained by performing point to point mapping of the measured flight data. This feature of NGN method enhances its application over a wider envelope of high angles of attack flight data.

In this paper, the development of a fault-tolerant control system for an aircraft that exploits both the hardware and analytical redundancy in the system is considered. A control allocation approach is developed where the total control command is computed and distributed among the available control surfaces. The actuator’s position and rate limits are taken into account in the optimisation problem. Existing fault-tolerant control allocation techniques produce look-up tables of control gains based on certain faults in the model. In contrast, the developed reconfigurable approach presented here incorporates a new process that redistributes control efforts which is updated whenever a fault occurs. In order to correlate between control effort redistribution and the fault magnitude, a fuzzy logic scheme is implemented, which handles a wide range of fault magnitudes on-line. The approach is applied for the most severe type of fault, which is the “lock-in-place” (jam) fault. Results show that the developed approach successfully handles the faulty situations and enhances aircraft flying responses by utilising the available healthy controls.

An analysis is presented which allows the engineer to quantitatively estimate the validity bounds of aerodynamic methods based in linear potential flows a-priori. The development is limited to quasi-steady planar flows with attached shocks and small body curvature. Perturbation velocities are parameterised in terms of Mach number and flow turning angle by means of a series-expansion for flow velocity based in the method of characteristics. The parameterisation is used to assess the magnitude of non-linear term-groupings relative to linear groups in the full potential equation. This quantification is used to identify dominant nonlinear terms and to estimate the validity of linearising the potential flow equation at a given Mach number and flow turning angle. Example applications include the a-priori estimation of the validity bounds for linear aerodynamic models for supersonic aeroelastic analysis of lifting surfaces and panels.

In this study, a series of numerical experiments are performed on supersonic/hypersonic flows over an adiabatic flat plate with transitionally and fully rough surfaces. The Mach numbers simulated are 4, 5, 6, and 7; the flight heights considered are 20, 24, 28, 32, and 36 km. First, a modified roughness correction is proposed and validated with the measured data for low-speed flat-plate cases. It is verified that for the equivalent sand grain heights in the intermediate and fully rough regimes, there is a good agreement with the semi-empirical formula available in the open literature. Then, this roughness correction is applied to high-speed flow regime to investigate the effects of flight heights and Mach numbers on drag for rough-wall flat-plate cases. It is found that within the roughness measured in real flight, the roughness height change has little effect on drag compared to the variations of both flight heights and Mach numbers. The drag coefficient derivation between rough-wall and smooth-wall conditions, achieves the maximum value of 0.79% for the 60 cases selected.

The pressure oscillation and terminal shock motion in a two dimensional inlet, which was designed for tandem configuration turbine-based combined cycle propulsion systems was investigated experimentally and numerically, respectively. The inlet was characterised by a bleed cavity upstream the inlet throat, an S-shape rectangular-to-circular diffuser and flowpaths for a turbine and a ramjet engine. The terminal shock motion was calculated through a second-order unsteady Reynolds-averaged Navier-Stokes scheme. The pressure and the terminal shock were unsteady when the combined cycle inlet operated at different conditions. With the terminal shock located in the throat and at the shoulder of the third ramp of the TBCC inlet, the pressure oscillation was significant and the shock exhibited unsteady streamwise motion with an oscillatory pattern. The amplitude of shock oscillation at these two conditions was 6mm and 12mm, respectively. When the shock was located downstream of the throat and upstream of the cowl lip, it oscillated in a small range. We defined this motion as the “shake” of the shock. This unsteady behaviour of the shock was caused by flow separation in the combined cycle inlet diffuser.