Book contents
- Reviews
- Gas Turbines for Electric Power Generation
- Gas Turbines for Electric Power Generation
- Copyright page
- Contents
- Preface
- 1 Introduction
- Part I Prerequisites
- Part II Fundamentals
- 5 Thermodynamics
- 6 Technology Factors
- 7 Heat and Mass Balance
- 8 Real Cycle Analysis
- 9 Turbine Cooling
- 10 Turbine Aero*
- 11 Compressor Aero*
- 12 Combustion
- 13 Materials
- 14 The Hardware
- Part III Extras
- Part IV Special Topics
- Book part
- Index
- References
9 - Turbine Cooling
from Part II - Fundamentals
Published online by Cambridge University Press: 15 February 2019
Book contents
- Reviews
- Gas Turbines for Electric Power Generation
- Gas Turbines for Electric Power Generation
- Copyright page
- Contents
- Preface
- 1 Introduction
- Part I Prerequisites
- Part II Fundamentals
- 5 Thermodynamics
- 6 Technology Factors
- 7 Heat and Mass Balance
- 8 Real Cycle Analysis
- 9 Turbine Cooling
- 10 Turbine Aero*
- 11 Compressor Aero*
- 12 Combustion
- 13 Materials
- 14 The Hardware
- Part III Extras
- Part IV Special Topics
- Book part
- Index
- References
- Type
- Chapter
- Information
- Gas Turbines for Electric Power Generation , pp. 193 - 216Publisher: Cambridge University PressPrint publication year: 2019
References
Henze, M., Bogdanic, L., Mühlbauer, K., Schneider, M., Effect of the Biot Number on Metal Temperature of Thermal-Barrier-Coated Turbine Parts – Real Engine Measurements, Journal of Engineering for Gas Turbines and Power, 135 (2013), 031029.Google Scholar
Young, J. B., Wilcock, R. C., Modeling the Air-Cooled Gas Turbine: Part 2 – Coolant Flows and Losses, Journal of Engineering for Gas Turbines and Power, 124 (2002), 212–222.Google Scholar
Lechner, C., Seume, J. (Eds.), Stationäre Gasturbinen, 2nd new revised edition (Berlin, Germany: Springer Verlag, 2010).Google Scholar
Lakhsminarayana, B., Fluid Dynamics and Heat Transfer of Turbomachinery, (New York: John Wiley & Sons, Inc., 1996).Google Scholar
Elmasri, M. A., GASCAN – An Interactive Code for Thermal Analysis of Gas Turbine Systems, Journal of Engineering for Gas Turbines and Power, 110 (1988), 201–210.CrossRefGoogle Scholar
Elmasri, M. A., Pourkey, F., “Prediction of Cooling Flow Requirements for Advanced Utility Gas Turbines – Part 1: Analysis and scaling of the Effectiveness Curve,” ASME 86-WA/HT-43.Google Scholar
Elmasri, M. A., “Prediction of Cooling Flow Requirements for Advanced Utility Gas Turbines – Part 2: Influence of Ceramic Thermal Barrier Coatings,” ASME 86-WA/HT-44.Google Scholar
Sultanian, B., Gas Turbines: Internal Flow Systems Modeling (Cambridge, UK: Cambridge University Press, 2018).CrossRefGoogle Scholar
Alizadeh, M., Izadi, A., Fathi, A., Sensitivity Analysis on Turbine Blade Temperature Distribution Using Conjugate Heat Transfer Simulation, Journal of Turbomachinery, 136 (2014), 011001.Google Scholar
Jordal, K., Bolland, O., Klang, A., Aspects of Cooled Gas Turbine Modeling for the Semi-Closed O2/CO2 Cycle with CO2 Capture, Journal of Engineering for Gas Turbines and Power, 126 (2004), 507–515.Google Scholar
Collins, M. F. et al., Development, Fabrication and Testing of a Prototype Water-Cooled Gas Turbine Nozzle, Transactions of the ASME, 105 (1983), 114–119.Google Scholar
Chiesa, P., Macchi, E., A Thermodynamic Analysis of Different Options to Break 60% Electric Efficiency in CC Power Plants, Journal of Engineering for Gas Turbines and Power, 126 (2004), 770–785.Google Scholar
Rice, I. G., The Reheat Gas Turbine with Steam-Blade Cooling – A Means of Increasing Reheat Pressure, Output, and Combined Cycle Efficiency, Journal of Engineering for Gas Turbines and Power, 104: 1 (1982), 9–22.Google Scholar
Schneider, M., Sommer, T., “Turbines for Industrial Gas Turbine Systems,” in: Modern Gas Turbine Systems: High Efficiency, Low Emission, Fuel Flexible Power Generation (Woodhead Publishing Series in Energy), 1st edition, Ed. Jansohn, P., (Cambridge, UK: Woodhead Publishing, Ltd., 2013).Google Scholar
Elderson, E. D., Scheper, G. W., Cohn, A., “Closed Circuit Steam Cooling in Gas Turbines,” ASME paper 87-JGPC-GT-1, 1987 Joint Power Generation Conference, October 4–8, 1987, Miami Beach, FL.Google Scholar
Facchini, B., Innocenti, L., Carnevale, E., “Evaluation and Comparison of Different Blade Cooling Solutions to Improve Cooling Efficiency and Gas Turbine Performances,” ASME Paper 2001-GT-0571, ASME Turbo Expo 2001, June 4–7, 2001, New Orleans, LA.Google Scholar
Han, J. C., Dutta, S., Ekkad, S. V., Gas Turbine Heat Transfer and Cooling Technology, (New York: Taylor & Francis, Inc., 2000).Google Scholar
Holland, M. J., Thake, T. F., Rotor Blade Cooling in High Pressure Turbines, Journal of Aircraft, 17: 6 (1980), 80-4061.Google Scholar
Horlock, J. H., Basic Thermodynamics of Turbine Cooling, Journal of Engineering for Gas Turbines and Power, 123 (2001), 583–591.Google Scholar
Horlock, J. H., Watson, D. T., Jones, T. V., Limitations on Gas Turbine Performance Imposed by Large Turbine Cooling Flows, Journal of Engineering for Gas Turbines and Power, 123 (2001), 487–494.Google Scholar
Torbidoni, L., Massardo, A. F., Analytical Blade Row Cooling Model for Innovative Gas Turbine Cycle Evaluations Supported by Semi-Empirical Air-Cooled Blade Data, Journal of Engineering for Gas Turbines and Power, 126 (2004), 498–506.CrossRefGoogle Scholar
Zhao, L., Wang, T., An Investigation of Treating Adiabatic Wall Temperature as the Driving Temperature in Film Cooling Studies, Journal of Engineering for Gas Turbines and Power, 134 (2012), 061032.Google Scholar