Shortly after construction of a subdivision in the southwest Denver metropolitan area in 1986, a portion of the subdivision built directly on steeply-dipping strata of the Pierre Shale began experiencing damaging differential movements, causing house foundations to fail and pavements to warp and crack. This formation is a Late Cretaceous marine clay-shale composed predominantly of fluvial mixed-layer illite/smectite and quartz. During deposition of the shale, periodic and explosive volcanism generated thin beds of bentonite, consisting initially of volcanic ash and subsequently altered to nearly pure smectite. Some of these bentonite beds were exposed in a trench adjacent to the subdivision and perpendicular to the strike of the steeply-dipping strata. The thickest bentonite beds correlated well with linear heave features that these beds parallel the bedrock strike throughout the subdivision were mapped via severely deformed pavements. Mineralogical data show the bentonite bed that correlates with the worst damage within the subdivision consists of about 62% smectite by weight with mixed-layer illite/smectite expandability of 92%. By comparison, a sample of the typical silty claystone, which is fluvial mixed-layer illite/smectite mixed with detrital quartz from the adjacent strata, had about 23% smectite by weight with 70% to 90% illite/smectite expandability. Geotechnical tests for swell potential show that samples of 2 bentonite beds swelled 39% to 43% compared to 2% to 8% for samples of the typical silty claystone. It is proposed that differential swell resulting from stratigraphically-controlled differences in clay mineralogy and grain-size is the primary factor controlling extreme damage for this geologic setting.

Clay minerals in shales from cores at Site 808, Nankai Trough, have been studied using X-ray diffraction (XRD), scanning transmission electron microscopy (STEM), and analytical electron microscopy (AEM) to compare the rates and mechanisms of illitization with those of coeval bentonites, which were described previously. Authigenic K-rich smectite having a high Fe content (∼7 wt. %) was observed to form directly as an alteration product of volcanic glass at a depth of ∼500 meters below seafloor (mbsf) with no intermediate precursor. Smectite is then largely replaced by Reichweite, R, (R = 1) illite-smectite (I-S) and minor illite and chlorite over depths from ∼550 to ∼700 mbsf. No further mineralogical changes occur to the maximum depth cored, ∼1300 m. Most smectite and I-S in shales are derived from alteration of glass, rather than being detrital, as is usually assumed. Discrete layer sequences of smectite, I-S, or illite coexist, indicating discontinuities of the transformation from smectite to (R = 1) I-S to illite. Authigenic Fe-rich chlorite forms concomitantly with I-S and illite, with the source of Fe from reactant smectite.

Smectite forms from glass with an intermediate precursor in coeval bentonites at approximately the same depth as in shales, but the smectite remains largely unchanged, with the exception of exchange of interlayer cations (K → Na → Ca) in response to formation of zeolites, to the bottom of the core. Differences in rates of illitization reflect the metastability of the clays. Temperature, structure-state, and composition of reactant smectite are ruled out as determining factors that increase reaction rates here, whereas differences in water/rock ratio (porosity/permeability), Si and K activities, and organic acid content are likely candidates.

Antibacterial clays in nature include a variety of clay mineral assemblages that are capable of killing certain human pathogens. Although clays have been used for medicinal applications historically, only in the last decade have analytical methods and instrumentation been developed that allow researchers to evaluate the antibacterial mechanisms of various clays applied medicinally. Comparisons of the mineralogical and chemical compositions of natural clays that kill bacteria have promoted a better understanding of the mineral properties that are toxic to a broad-spectrum of human pathogens, including bacteria that have developed resistance to antibiotics. Popular literature is filled with reports of ‘healing’ clays, that, when tested against pathogens in vitro and compared to controls, do not appear to have bactericidal properties. It is important, however, to differentiate what properties make a clay ‘healing,’ versus what makes a clay ‘antibacterial.’ Most antibacterial clays identified to date buffer pH conditions of a hydrated clay outside the range of conditions in which human pathogens thrive (circum-neutral pH) and require oxidation reactions to occur. It is the change in oxidation state and pH imposed by the hydrated clay, applied topically, that leads to a chemical attack of the bacteria. Healing clays, on the other hand, may not kill bacteria but have soothing effects that are palliative. This article reviews some of the historical uses of clays in medicine but focuses primarily on the common characteristics of natural antibacterial clays and early studies of their antibacterial mechanisms. In this era of bacterial resistance to antibiotics, mimicking the antibacterial mechanisms exhibited by natural clays could be advantageous in the development of new antimicrobial agents.

Rb-Sr and oxygen isotope studies, in addition to K-Ar isotopic determinations published previously, are reported on diagenetic and hydrothermal fundamental particles (particle thickness of 0.03 to 0.05 nm and particle ab size of 0.02–0.05 µm) of the East-Slovak Basin. The combined data set allows us to ascertain the crystallization conditions of the illite material from two bentonite units collected at two basinal sites located ~20 km apart, and characterized by prolonged diagenetic conditions induced by progressive burial. A bentonite rock characterized by a short hydrothermal event from the Zempleni mountains to the SW of the East-Slovak basin is also studied.

For the two first sites, the δ18O values increase in one case and decrease in the other, when the size of the diagenetic fundamental particles from bentonite samples increases. These variations suggest that temperature increased in one and decreased in the second of the two samples collected in the basin, while the particles were growing. In the case of the hydrothermal bentonite, the δ18O values of the different size-fractions consisting of fundamental particles remain about constant, suggesting constant temperature and fluid chemistry.

The Rb-Sr dates of the fundamental particles of the three bentonite rocks were systematically higher than the corresponding K-Ar ages. The 87Sr/86Sr ratios, which are initially involved in the particle nucleation, appeared higher than that of contemporaneous sea-water. In all cases, the initial 87Sr/ 86Sr ratio decreases when particle size increases, which implies supply of external Sr into the bentonite units. This external Sr seems to have had an 87Sr/86Sr ratio close or identical to that of the contemporaneous sea water. This means that Sr, probably of sea-water origin, progressively diffused from host shales into the bentonite units, during burial diagenesis. In turn it favors the suggestion made previously about diffusion of K from shales into the bentonite layers during illitization of the smectite from these units.

The compressibility behavior of clays is governed by the electrical double layer formed around the clay particles. The Gouy-Chapman diffuse double layer theory is often utilized to predict the compressibility behavior of clay minerals. The theory does not consider the effect of the size of the cations, however, and thus predicts unrealistically small void ratios for compacted bentonites under large mechanical pressures expected in high-level nuclear waste-repository applications. In this study, the Stern layer was introduced to incorporate the cation size effect in the prediction of the compressibility behavior of bentonites. The overall diffuse double-layer thickness at large pressures was much smaller than the initially assumed Stern layer thickness based on the exchangeable cation size for all the bentonites studied. A compressible Stern layer was, therefore, considered for the first time in the prediction of the compressibility behavior of bentonites. The compression behavior of the Stern layer under the applied loading is influenced by the ratio of the mid-plane to the Stern potential, which is dependent on the type and composition of the exchangeable cations on the clay surface. Stern layer compression was initiated when the potential ratio was in the range 0.65–0.75 for bentonites with various surface cation characteristics. The incorporation of cation size and a compressible Stern layer provided significant improvements over the existing models in predicting the compressibility behavior of bentonites over a wide pressure range. The compressibility data predicted by the proposed model showed very good agreement with the data measured for five bentonites from the literature in the pressure range 0.1–42 MPa.

Because of their isolating capacity, smectite-rich clays have been proposed as buffer and backfill materials in high-level radioactive waste repositories. These repositories have to guarantee long-term safety for ~1 million years. Thermodynamics and kinetics of possible alteration processes of bentonite determine its long-term performance as a barrier material. Smectites in 25 different clays and bentonites were investigated in order to identify possible differences in their rates of alteration. These samples were saturated for 30 days in 1 M NaCl solution and deionized water, and then overhead rotated at speeds of 20 rpm and 60 rpm. Depending on the octahedral and interlayer composition, each of the smectites studied had specific rate of alteration, a so-called specific dissolution potential of smectite. The bentonites were classed as ‘slow-reacting bentonite’, ‘moderate-reacting bentonite’, or ‘fast-reacting bentonite’ corresponding to a relatively low (ΔP specific dissolution potential — <-5%), moderate (-5% < ΔP < -20%), or high specific dissolution potential (ΔP > -20%), respectively. The larger the amount of octahedral Fe and Mg compared to octahedral Al, the greater the specific dissolution potential. The present study found that the interlayer composition has a discernible impact on the rate of alteration. In experiments with rotation speeds of 60 rpm and a 1 M NaCl solution, Na+ was found to be the stabilizing cation in the interlayers of all the smectites. The Na-stabilizing mechanism was identified in only some of the smectites (type A) in experiments with 20 rpm (1 M NaCl solution). A second stabilization mechanism (by interlayer cations; Ca and Mg) was identified for other smectites (type B). Each bentonite has a specific rate of alteration. ‘Slow-reacting bentonite’ and clay with smectite-illite interstratifications are recommended as potential clay barriers in HLW repositories. The experimental and analytical procedures described here could be applied to potential barrier materials to identify ‘slow-reacting bentonite’.

A detailed stratigraphic and facies reconstruction of a bentonitized acid-tuff succession, deposited within the transgressive systems tract of the Upper Miocene-Sarmatian Ser-3 eustatic cycle, at Sajóbábony, northern Hungary, was performed via petrographic, mineralogical and geochemical analyses. The purpose of the work was to analyze the degree of alteration of the volcanogenic sediments, as an indicator of the relative volcanic sedimentation rate. This may have an important role in indicating volcanic periods synchronous with sedimentation or reconstructing the volcanosedimentary paleoconditions. Sample pairs were collected from each bentonite and tuff layer, and, to facilitiate microstratigraphic relations, samples were collected every 10 cm within bentonite layers. Mineralogical analyses were performed by X-ray diffraction and geochemical analyses by inductively coupled plasma-mass spectroscopy.

The CaO/K2O and Eu/La ratios correlate with each other and with a montmorillonite/X-ray-amorphous phase ratio, reflecting Ca and Eu incorporation associated with devitrification and smectite formation. In accordance with the current literature, these mineralogical and geochemical proxies can be related primarily to the weathering processes. Considering vertical distributions in a sequence-stratigraphic context, the Ca content and Eu/La values show that local peaks and Eu anomalies characteristic of acid tuffs show minima at flooding surfaces (FS). Within a bentonite layer, representing a single transgressive period, the repeated events of dust-tuff accumulations have been determined by K2O/CaO and La/Eu peaks, confirmed also by the Eu anomalies in the rare earth element (REE) patterns, thus leading to the conclusion that the level of alteration is closely correlated with the elimination of terrigenous input and a minimum in volcanic sedimentation rate allowing more intensive alteration of the deposited volcanic material. In the case of fine tuff beds, Eu anomalies on REE patterns reflect limited alteration at the bottom and more intensive alteration in the upper parts of the beds, reflecting the effect of infiltration of sea water into the pores.

A version of thermoporometry dedicated to analyzing the pore network of expanding clays is proposed here. The blurred, wide Differential Scanning Calorimetry (DSC) peak obtained upon the melting of a frozen clay sample is processed by means of a deconvolution analysis based on searching for such a temperature distribution of “pulse-like heat events” which, convolved with the apparatus function, gives a minimal deviation from the observed heat flux function, i.e. the calorimetric signal. As a result, a sharp thermogram was obtained which can be transformed easily into the pore-size distribution curve. Results obtained for samples of two Clay Minerals Society Source Clays (montmorillonites SWy-2 from Wyoming and STx-1b from Texas) at different water contents indicate a greater resolution and sensitivity than that achieved by classical thermoporometry using the unprocessed DSC signal. Phenomena corresponding to the evolution of the pore network as a function of the water content have been detected in samples with large water contents subjected to free drying prior to the experiments.

The effect of a saline environment on illitization in volcanoclastic rocks is examined in deep boreholes in the East Slovak Basin. Based on X-ray diffraction analysis, it is concluded that illite-smectite (I–S) expandability is always less in the salt-bearing bentonites (SBB) than in the salt-free bentonites (SFB) for a given depth interval. These two lithologies can be distinguished easily by water-leachate chemistry. Within the depth interval 2100–2500 m, the expandability in SBB varies within the range 25–10% expandable with R1 and R3 ordering in SBB and 68–35% expandable with R0 ordering in SFB. In two shallow SBB samples the expandability is close to that of SFB, suggesting that salinity alone does not enhance the illitization; but salinity may enhance it when combined with higher burial temperature. Vitrinite reflectance and Tmax of RockEval pyrolysis measured in adjacent shales confirm that the increased illitization in SBB is not due to heating and/or erosion. The model of burial and thermal history calibrated by organic maturity suggests that the same thermal history produces two different expandabilities in the two lithologies (SBB and SFB). Particle thickness measurements and K-Ar data were used to deduce the crystal growth mechanism of illitization in SBB. Whereas surface-controlled growth is typical for SFB, simultaneous nucleation and growth played a more important role in the case of SBB. The effect of a salty environment on the illitization is not yet fully understood and may have severe consequences for the utilization of bentonites as engineering barriers in radioactive waste disposal sites if salt formations used as host rocks are taken into account.

The cation exchange capacity (CEC) is one of the most important properties of clays in terms of their performance in both natural and technical processes. For decades, common methods for determining exchangeable cations have failed when calcareous clays or soils were examined, because calcite is at least partly dissolved throughout the exchange experiment which in turn increases measureable Ca2+ concentrations. As a result, exchangeable Ca2+ and the sum of exchangeable cations by far exceed the amount of negative charges. In the past, the silver-thiourea method (AgTU) has been modified to overcome this problem (AgTUcalcite), but is unsatisfactory as the method is laborious. In the present study three new methods based on two alternative metal complexes, cobalt(III) hexamine (CoHex) and copper(II) triethylenetetramine (Cu-trien), are proposed. The optimum solid/liquid ratios of these methods and the optimum complex concentration of Cu-trien are reported, depending on the mineralogical composition of the samples. The key development is that the exchange solutions are saturated with respect to calcite prior to the experiment. Approximately 70–90% of the dissolution of calcite present as an admixture in a clay sample is suppressed in the subsequent cation exchange experiment, but not all. The Ca2+ exchange is not suppressed and there is no evidence for any precipitation of this Ca2+. Three possibilities for how to handle this problem are discussed, one of which is to perform no further correction. The resulting error arises from the remaining calcite solubility of the different solutions after pre-treatment with calcite. This corresponds to errors of 0.2–1.3 (CoHexcalcite)and 0.7–8.4 (Cu-triencalcite) meq/100 gCa2+ for samples with small and large CEC values, respectively. As a consequence of the poor performance of Cu-triencalcite for samples with large CEC, a more concentrated Cu-trien5 × calcite solution was developed which performed much better: 0.1–0.8 meq/100 g(Cu-trien5 × calcite). For Cu-trien5 × calcite and CoHexcalcite at least, the errors are in the range of the non-systematic scattering for exchangeable Ca2+ determination. Therefore, the methods suggested provide ‘operationally correct’ Ca2+ values without additional effort. Moreover, owing to the high selectivity of the index cations applied in the present study, only one exchange step is required, providing a significant advantage over the AgTUcalcite method.

The aim of the present study was to find methodological tools to obtain reasonable results for exchangable Ca2+ of gypsiferous bentonites. Cation exchange capacity (CEC) is an important property of clays. Numerous methods for calculating CEC and exchangeable cations exist; determination of exchangeable Ca2+ fails, however, when gypsiferous clays are examined because gypsum is dissolved throughout the exchange experiment, which in turn increases measureable Ca2+ concentrations. Several new methods (AgTUcalcite, CoHexcalcite, and Cu-trien5×calcite) have been developed to overcome a similar problem occurring with calcite by using exchange solutions saturated with respect to calcite prior to the experiment. In the present study these three solutions were also pre-treated with gypsum and labeled AgTUCcGp, CoHexCcGp, and Cu-trien5×CcGp. The special solutions were applied first to a gypsum- and calcite-free bentonite with known reference values for exchangeable Ca2+. The resulting exchangeable Ca2+ values obtained did not match with reference values. The solutions were then applied to natural calcareous and gypsiferous bentonites but only the proposed AgTUCcGp test method was successful. The performance of AgTUCcGp was relatively poor when applied to calcareous non-gypsiferous bentonites, the third group of test materials. Reasonable values for exchangeable Ca2+ of gypsiferous clays were obtained using a combination of two separate results: (1) calcite saturation of exchange solution (e.g. Cu-trien5×calcite) and (2) quantification of gypsum with suitable mineralogical methods. Result 1 eliminates errors caused by calcite dissolution though it is still incorrect because it contains significant amounts of Ca2+ from gypsum dissolution. After proving that gypsum was completely dissolved during the exchange experiment, result 2 was used to subtract the theoretical Ca2+ portion of gypsum from result 1. The initial concentration of gypsum of the samples studied was <1 wt.%, typical of many commercial bentonites. Using this combined procedure the sum of exchangeable cations is very close to the CEC, though it still exceeds the CEC by, on average, 3%, which is a satisfactory improvement. The resulting exchangeable Ca2+ values can be considered as operationally correct using this approach. Ca2+ saturation (Ca/CEC in %) of seven gypsiferous bentonites ranges from 1 to 69%.

The determination of the cation exchange capacity (CEC) of clays by exchange with the cationic copper complexes [Cu(en)2]2+ and [Cu(trien)]2+ is revisited. The procedures reported by Bergaya & Vayer (1997) and Meier & Kahr (1999) are modified slightly. The concentration of the copper complexes in the equilibrium solutions is measured by spectral photometry. Correct CEC values of the [Cu(en)2]2+ exchange are only obtained when a buffer (‘tris’, tris (hydroxymethyl) aminomethane, pH = 8) is added to the equilibrium solution after separation of the clay, because the molar extinction coefficient of this complex depends on the pH of the solution. A standard procedure is recommended as a reference method. In most cases, tris addition is not needed for the determination with [Cu(trien)]2+ cations. Nevertheless, tris addition is recommended in the standard procedure. Determination of CEC for 40 samples (kaolins, ‘common clays’, bentonites, montmorillonites and beidellite) shows a good agreement between measurements using [Cu(en)2]2+ and [Cu(trien)]2+ cations and with results by the ammonium acetate method.

This study is located on the bentonite outcrop of ‘El Toril’ (Cabo de Gata, Almeria, Spain), where acid solutions have resulted in an alteration front that has caused physical, chemical and mineralogical changes in the bentonite material. The main objective is to assess these changes and to draw a model of evolution of this front in the outcrop. The most important chemical and mineralogical changes observed consist mainly of the loss of mass in the bentonite, the formation of kaolinite, the precipitation of jarosite and alunite from leachates and important changes in the rare earth element distribution pattern. No sulphurs have been identified in the pyroclastic rock at the top of the outcrop, but the presence of dissolution marks and the high concentrations of As, Pb and V in the rock overlying the bentonite point towards the existence, in principle, of these sulphurs and suggest that meteoric alteration is mainly responsible for the genesis of the outcrop.

K-Ar dating of mixed-layer illite-smectite from clay fractions extracted from pyroclastic horizons was used to address the controversy about the age and mechanism of the thermal alteration of Carboniferous rocks from the Upper Silesia Coal Basin (USCB). The clay fractions were also investigated by X-ray diffraction in order to select for dating samples possibly rich in illitesmectite, and to evaluate the K-Ar dates for possible contamination by K-bearing pre-diagenetic minerals, of pyroclastic or epiclastic origin.

The K-Ar dates document intense Variscian tectonic burial illitization produced by thrusting (~290 Ma) in the SW of the basin, and the lack of intense burial illitization in the NE, which is consistent with sedimentological models of the basin. The burial illitization in its final phase (<30%S in illite-smectite) involved incorporation of measurable amounts of ammonium cation in the illite structure (substitution for K).

Advanced illitization in the NE of the basin is much younger than its tectonic inversion (uplift and erosion started in Permian), and the corresponding K-Ar dates have to be interpreted as the result of a Mesozoic thermal event, which produced widespread pervasive illitization at shallow depth. This event was dated at 175 Ma, but it may have started earlier and could have lasted longer. This conclusion is consistent with widespread evidence of a major Mesozoic thermal event all over Central Europe, produced by rifting and lithospheric thinning during the opening of the Tethys and Atlantic oceans.

This study demonstrates that smectite illitization histories may be very complex, and that the nature of the illitization mechanism results in mixed K-Ar dates encompassing pro-longed or multiple illitization histories. Dating of several grain-size fractions may help to unravel such histories.

When a calibration using data from Neogene sedimentary basins is applied, vitrinite reflectance and %S in I-S indicate similar palaeotemperatures of tectonic burial diagenesis in the USCB, but they produce very different estimates of the temperature of the thermal event.

The aspect ratios of common clay minerals have been determined from conductometric titrations. The sample set comprises 11 Na-saturated bentonites, 16 smectites with different interlayer cations, three illites/muscovites and two talc dominated specimens. It is shown that the aspect ratios of smectites saturated with divalent cations are lower than those of the same smectite saturated with a monovalent cation. This observation is discussed in terms of the number of smectite layers making up a particle.

The upper Wenlock Series (Homerian Stage) of the northern Midland Platform, England, contains numerous volcanic bentonite clay layers. At Wren's Nest Hill, Dudley, 15 bentonites have been investigated and comparisons with the type-Wenlock have been made by means of two key sections along Wenlock Edge, Shropshire. In total 22 bentonites have been investigated and their clay and sand-grade mineralogies determined. Rare earth element (REE) and yttrium concentrations of apatite grains contained within ten of the bentonites have been established allowing geochemical fingerprinting as an indication of provenance of source magmas and identification of geochemical marker beds. Based on the analysis of REE and yttrium concentrations it seems likely that the majority of these bentonites originated from a granodiorite magmatic source. Comparisons with published Llandovery and lower Wenlock age bentonites indicate generally more enrichment in light REEs relative to heavy REEs. In addition, close geochemical similarities between bentonites along Wenlock Edge and at Wren's Nest Hill strongly argue for their presence as precise stratigraphic equivalents within the upper Much Wenlock Limestone Formation. These correlations are further supported by geophysical data from borehole wire-line logs across the West Midlands. Finally, a chemically distinct mid-Homerian episode of volcanism is identified and represents a potentially important marker interval between the study area and other similarly aged bentonites reported from the Island of Gotland, Sweden.

Sanidine composition and bulk geochemistry of volcanic ash beds from the East Baltic indicate the subalkaline nature of the volcanism near the margins of the Baltica plate during the Silurian. Several bentonites in the Wenlock include a previously unknown sanidine with 48 to 58 mol % of the Na+Ca component. In contrast to the earlier Telychian volcanism, sodium-rich sanidine occurs in ash beds which originate from relatively moderately evolved dacitic magma. The studied material from two drill cores integrated with previous research enables production of a more complete list of 49 volcanic eruption layers for the lower to middle Wenlock in the East Baltic. This updated list of bentonites characterized by their sanidine compositions forms a good basis for future integrated bio- and chemostratigraphic correlations in northern Europe.