The British Antarctic Survey's (BAS) Rapid Access Isotope Drill (RAID), designed for rapid drilling to survey prospective ice core sites, has been deployed at multiple Antarctic locations over 6 years. This drilling method creates ice chippings that can be discretely sampled and analysed for their chemical and water isotopic composition. Ice sampling methods have evolved since the first uses of the BAS RAID, enabling a more quantifiable sample resolution. Here, we show that water isotope records obtained from RAID ice are comparable to those of equivalent depth resolution from proximal ice cores. Records of chemical impurities also show good agreement with nearby cores. Our findings suggest that the RAID is suitable for both chemical and isotopic reconnaissance of drilling sites. Residual contamination of certain ions is discussed, with proposed design changes to avoid this issue with future use.

We analysed the three-dimensional microstructure of sea ice by means of X-ray-micro computed tomography. Microscopic (brine- and air- pore sizes, numbers and connectivity) and macroscopic (salinity, density, porosity) properties of young Arctic sea ice were analysed. The analysis is based on ice cores obtained during spring 2016. Centrifuging of brine prior to CT imaging has allowed us to derive confident relationships between the open, vertically connected and total porosity of young sea ice at relatively high temperatures. We analysed the dependence of the microscopic properties on vertical position and total brine porosity. Most bulk properties (salinity, density) and pore space properties (pore sizes and their distribution) show a strong dependence on total brine porosity, but did not change significantly over the course of the field work. However, significant changes were observed for pore numbers (decreasing over time) and pore connectivity (increasing over time). CT-based salinity determinations are subject to larger than standard uncertainties (from conductivity), while the CT method yields important information about the salinity contributions from closed and open pores. We also performed a comparison of CT-based air porosity with calculations based on density from hydrostatic weighing. The consistency is encouraging and gives confidence to our CT-based results.

Rapid Access Ice Drill is a new drilling technology capable of quickly accessing the glacial bed of Antarctic ice sheets, retrieving ice core and rock core samples, and providing boreholes for downhole logging of physical properties. Scientific goals include searching for old ice near the glacial bed and sampling subglacial bedrock. During field trials near McMurdo Station on a piedmont glacier at Minna Bluff in the 2019–20 austral summer, we successfully completed a ‘top-to-bottom’ operational sequence in three boreholes by (1) augering through firn, (2) creating a borehole packer seal in non-porous ice, (3) establishing fluid circulation, (4) quickly drilling a borehole in ice at penetration rates up to 1.2 m min−1, (5) acquiring a short ice core at depth, (6) penetrating the glacial bed at a depth of ~677 m, (7) recovering a 3.2 m core of ice, basal till and subglacial bedrock, (8) optically logging the borehole on wireline, (9) testing hydrofracture potential by overpressuring the borehole fluid and (10) operating in an environmentally benign yet rapid field mode. Minna Bluff testing, therefore, demonstrates the effectiveness of this integrated system to drill rapidly through thick ice and penetrate across the glacial bed to take cores of bedrock.

To understand the long-term climate and glaciological evolution of the ice sheet in the region bordering the Weddell Sea, the British Antarctic Survey has undertaken a series of successful ice core projects drilling to bedrock on Berkner Island, James Ross Island and the Fletcher Promontory. A new project, WACSWAIN, seeks to increase this knowledge by further drilling to bedrock on two further ice rises in this region. In a single-season project, an ice core was recovered to bedrock at 651 m on Skytrain Ice Rise using an ice core drill in a fluid-filled borehole. In a second season, a rapid access drill was used to recover ice chips to 323 m on Sherman Island in a dry borehole, though failing to reach the bedrock which was at an estimated depth of 428 m.

A deep ice core was drilled at Dome A, Antarctic Plateau, East Antarctica, which started with the installation of a casing in January 2012 and reached 800.8 m in January 2017. To date, a total of 337 successful ice-core drilling runs have been conducted, including 118 runs to drill the pilot hole. The total drilling time was 52 days, of which eight days were required for drilling down and reaming the pilot hole, and 44 days for deep ice coring. The average penetration depths of individual runs were 1 and 3.1 m for the pilot hole drilling and deep ice coring, respectively. The quality of the ice cores was imperfect in the brittle zone (650−800 m). Some of the troubles encountered are discussed for reference, such as armoured cable knotting, screws falling into the hole bottom, and damaged parts, among others.

The Japanese second deep ice coring project was carried out at Dome Fuji, Antarctica. Following the drilling of the pilot hole in 2001, deep ice core drilling led by the Japanese Antarctic Research Expedition (JARE) was conducted over four austral summer seasons, beginning with the 2003/04 season and reached a depth of 3035.22 m near the bedrock in January 2007. The new drill was designed and developed with the goals of (1) solving the problems encountered during the first JARE deep coring drill and (2) achieving more efficient drilling. In particular, the maximum core length that can be drilled at one time was increased from 2.30 m to 3.84 m and the chip storage efficiency was enhanced by a special pipe with many small holes. This paper gives an outline of the improved drilling system, the progress of drilling and various drilling data.

An intermediate-depth (1751 m) ice core was drilled at the South Pole between 2014 and 2016 using the newly designed US Intermediate Depth Drill. The South Pole ice core is the highest-resolution interior East Antarctic ice core record that extends into the glacial period. The methods used at the South Pole to handle and log the drilled ice, the procedures used to safely retrograde the ice back to the National Science Foundation Ice Core Facility (NSF-ICF), and the methods used to process and sample the ice at the NSF-ICF are described. The South Pole ice core exhibited minimal brittle ice, which was likely due to site characteristics and, to a lesser extent, to drill technology and core handling procedures.

Using significant technological breakthroughs and unconventional approaches, the goal of the in situ probing of glacier ice for a better understanding of the orbital response of climate (SUBGLACIOR) project is to advance ice core research by inventing, constructing and testing an in situ probe to evaluate if a target site is suitable for recovering ice as old as 1.5 million years. Embedding a laser spectrometer, the probe is intended to make its own way down into the ice and to measure, in real time and down to the bedrock, the depth profiles of the ice δD water isotopes as well as the trapped CH4 gas concentration and dust concentration. The probe descent is achieved through electromechanical drilling combined with continuous meltwater sample production using a central melting finger in the drill head. A key aspect of the project lies in the design and implementation of an efficient method to continuously transfer to the surface the ice chips being produced by the drill head and from the refreezed water expulsed downstream from the melting finger, into the borehole. This paper presents a detailed calculation and analysis of the flow rates and pressure conditions required to overcome friction losses of the drilling fluid and to effectively transport ice chips to the surface.

A series of new synthetic armored cables were developed and tested to ensure that they were suitable for use with the RECoverable Autonomous Sonde (RECAS), which is a newly designed freezing-in thermal ice probe. The final version of the cable consists of two concentric conductors that can be used as the power and signal lines. Two polyfluoroalkoxy jackets are used for electrical insulation (one for insulation between conductors, and the other for insulation of the outer conductor). The outer insulation layer is coated by polyurethane jacket to seal the connections between the cable and electrical units. The 0.65 mm thick strength member is made from aramid fibers woven together. To hold these aramid fibers in place, a sheathing layer was produced from a polyamide fabric cover net. The outer diameter of the final version of the cable is ~6.1 mm. The permissible bending radius is as low as 17–20 mm. The maximal breaking force under straight tension is ~12.2 kN. The cable weight is only ~0.061 kg m−1. The mechanical and electrical properties and environmental suitability of the cable were determined through laboratory testing and joint testing with the probe.

The Winkie Drill is an agile, commercially available rock coring system. The U.S. Ice Drilling Program has modified a Winkie Drill for subglacial rock and ice/rock interface coring, as well as drilling and coring access holes through ice. The original gasoline engine was replaced with an electric motor though the two-speed gear reducer and Unipress hand feed system were maintained. Using standard aluminum AW34 drill rod (for 33.5 mm diameter core), the system has a depth capability of 120 m. The drill uses forward fluid circulation in a closed loop system. The drilling fluid is Isopar K, selected for favorable properties in polar environment. When firn or snow is present at the drill site, casing with an inflatable packer can be deployed to contain the drill fluid. The Winkie Drill will operate from sea level to high altitudes and operation results in minimal environmental impact. The drill can be easily and quickly assembled and disassembled in the field by two people. All components can be transported by Twin Otter or helicopter to the field site.

Significant upgrades to the Rapid Air Movement (RAM) Drill were developed and tested by the US Ice Drilling Program in 2016 through 2020 for the U.S. National Science Foundation. The design of the system leverages the existing infrastructure of the RAM Drill with the goal of greatly reducing the logistical burden of deploying the drill while maintaining the ability to drill an access hole in firn and ice to 100 m in 40 min or less. In this paper, characteristics of the drill are described, along with a description of the drill performance during the testing at Raven Camp in Greenland and at WAIS Divide Camp in Antarctica.

Monitoring the tension in cables is significant in some ice drill and deepwater applications. Take our RECoverable Autonomous Sonde (RECAS) for example. It is able to melt a hole to the bottom of ice sheet and is able to move upwards. A winch is installed inside RECAS to release and recover the cable, whose tension needs to be monitored in real time in order to control the behavior of the winch. The high pressure of deep water and limited installation space pose great challenges in sensor development. In this paper, two editions of newly designed deepwater tension sensors are proposed. The first edition is based on a fresh hydraulic load module that operates in high pressure environment and the second edition tension, which aims to improve the accuracy, applies a newly designed watertight load module. Detailed force transmission and characteristic analysis of the sensors are carried out. The sensors have got through a series of experiments, including calibration experiments, pressure experiments and field experiments. The resultant accuracy of the second edition sensor, which has a better performance, is over 2% under the measuring range of 1000 kg and the dimension of the final sensor is as compact as 150 mm × 137 mm × 86 mm.

A new drilling system was developed by the US Ice Drilling Program (IDP) to rapidly drill through overlying ice to collect subglacial rock cores. The Agile Sub-Ice Geological (ASIG) Drill system is capable of drilling up to 700 m of ice in a continuous manner. Intermittent ice core samples can be taken as needed. Ten-plus meters of subglacial bedrock and unconsolidated, frozen sediment cores can be drilled with wireline core retrieval. The functionality of the drill system was demonstrated in 2016–17 at the Pirrit Hills, Antarctica where 8 m of high-quality, continuous granite core was retrieved beneath 150 m of ice. The particulars of the drill system development, features and performance are discussed.

The Antarctic subglacial drilling rig (ASDR) is designed to recover 105 mm-diameter ice cores up to 1400 m depth and 41.5 mm-diameter bedrock cores up to 2 m in length. In order to ensure safe and convenient drilling, drilling auxiliaries are designed to support fieldwork and servicing. These auxiliaries are subdivided into several systems for power supply, drill tripping in the borehole, ice core and chip processing, and drill servicing and maintenance. The required equipment also includes two generators, a drilling winch with a cable, logging winch with a cable, control desk, pipe handler with a fixed clamp, chip chamber vibrator, centrifuge, emergency devices and fitting and electrical tools. Additionally, several environmental protective measures such as a new liquid-tight casing with a thermal casing shoe and a bailing device for recovering drilling fluid from the borehole were designed. Most of the auxiliaries were tested during the summer of 2018–2019 near Zhongshan Station, East Antarctica while drilling to the bedrock to a depth of 198 m.

Drilling to the bedrock of ice sheets and glaciers offers unique opportunities for examining the processes occurring in the bed. Basal and subglacial materials contain important paleoclimatic and paleoenvironmental records and provide a unique habitat for life; they offer significant information regarding the sediment deformation beneath glaciers and its effects on the subglacial hydraulic system and geology. The newly developed and tested Antarctic subglacial drilling rig (ASDR) is designed to recover ice and bedrock core samples from depths of up to 1400 m. All of the drilling equipment is installed inside a movable, sledge-mounted, temperature-controlled and wind-protected drilling shelter and workshop. To facilitate helicopter unloading of the research vessel, the shelter and workshop can be disassembled, with individual parts weighing <2–3 tons. The entire ASDR system weighs ~55 tons, including transport packaging. The ASDR is designed to be transported to the chosen site via snow vehicles and would be ready for drilling operations within 2–3 d after arrival. The ASDR was tested during the 2018–2019 summer season near Zhongshan Station, East Antarctica. At the test site, 2-week drilling operations resulted in a borehole that reached bedrock at a depth of 198 m.

A new, modified version of the cable-suspended Ice and Bedrock Electromechanical Drill (IBED) was designed for drilling in firn, ice, debris-rich ice and rock. The upper part of the drill is almost the same for all drill variants and comprises four sections: cable termination, a slip-ring section, an antitorque system and an electronic pressure chamber. The lower part of the IBED comprises an auger core barrel, reamers, a core barrel for ice/debris-ice drilling and a conventional geological single-tube core barrel or custom-made double-tube core barrel. First, the short and full-scale field versions of the IBED were tested at an outdoor testing stand and a testing facility with a 12.5 m-deep ice well. Then, in the 2018–2019 summer season, the IBED was tested in the field at a site ~12 km south of Zhongshan Station, East Antarctica, and a ~6 cm bedrock core was recovered from a 198 m-deep borehole. A total of 18 d was required to penetrate the ice sheet. The retrieved core samples of blue ice, basal ice and bedrock provided valuable information regarding the Earth's paleo-environment.

In many cases, the efficiency and safety of a drilling project depend on the reliability of the electrical and electronic control system, as the process progresses without visual access of the operator. The electrical and electronic system provides and regulates the power supply for the drill, collects and monitors the drill data during the whole operating process, and sends and receives the control instructions and feedback signals. The entire system is composed of the surface, borehole and software subsystems. The surface subsystem serves for operating the drilling process, transmitting the drilling and environmental data, and supplying power for the drill motor and downhole control system. The borehole subsystem is generally intended for borehole data acquisition, drill motor control, power regulation and communication. The software subsystem is designed for human–computer interaction, data processing and storage, and programming of signal acquisition and transmission of data. The control system of Antarctic subglacial drilling rig was tested during the 2018–2019 summer season near Zhongshan Station, East Antarctica, in the course of drilling to the bedrock at a depth of 198 m. It exhibited a steady and efficient performance without significant system failures.

The British Antarctic Survey Rapid Access Isotope Drill is an innovative new class of electromechanical ice drill, which has recently been used to drill the deepest dry hole drilled by an electromechanical auger drill. The record-breaking depth of 461.58 m was drilled in just over 104 hours at Little Dome C. The drill collects ice chippings, for water stable isotope analysis, rather than an ice core. By not collecting a core the winch can be geared for speed rather than core breaking and is lightweight. Furthermore, emptying of the chippings is performed by simply reversing the drill motor on the surface reducing the overall drilling time significantly. The borehole is then available for instrumentation. We describe the drill in its current state including modifications carried out since it was last deployed. Test seasons and the lessons learned from each are outlined. Finally, future developments for this class of drill are discussed.

Ice-core drilling to depths of 200–300 m is an important part of research studies concerned with paleoclimate reconstruction and anthropogenic climate change. However, conventional drilling methods face difficulties due to firn permeability. We have developed an electromechanical ice-core drill with air reverse circulation at the hole bottom. We believe that the new drilling system will recover ice cores faster than shallow auger drills, with high efficiency and low energy consumption. The theoretically estimated up-hole speed of the airflow should be not <7.7 m s−1 to allow proper removal of ice cuttings from the borehole bottom. The computer simulation and test results showed that the design of the new ice-coring drill is feasible. The maximum allowed penetration rate depends by square law on airflow.

The Institute of Low Temperature Science at Hokkaido University conducted ice-core drilling in alpine glaciers in the northern North Pacific region to reconstruct climate change in this region for the past few hundred years. We drilled two ice cores in the Kamchatka Peninsula, Russia. An ice core with a length of 211 m was drilled on a glacier at the summit caldera of Ushkovsky mountain in 1998. A second core, with a length of 115m (until bedrock was reached), was drilled on a glacier at the summit caldera of Ichinsky mountain in 2006. We drilled three further ice cores in Alaska, USA. Two ice cores with lengths of 50 and 212m were drilled on a glacier at the summit caldera of Mount Wrangell in 2003 and 2004. The third ice core was drilled on the ice divide among three glaciers, Black Rapids, Trident and Susitna glaciers, which represent a flat saddle north of Aurora Peak in the Alaska Range. This paper details the field operations and characteristics of the different ice-drilling systems used and the problems encountered.