Exploiting high-energy electron beams colliding into high-intensity laser pulses brings an opportunity to reach high values of the dimensionless rest-frame acceleration $\chi$ and thereby invoke processes described by strong-field quantum electrodynamics (SFQED). Measuring deviations from the results of Furry-picture perturbation theory in SFQED at high $\chi$ can be valuable for testing existing predictions, as well as for guiding further theoretical developments. Nevertheless, such experimental measurements are challenging due to the probabilistic nature of the interaction processes, dominating signals of low-$\chi$ interactions and limited capabilities to control and measure the alignment and synchronization in such collision experiments. Here we elaborate a methodology of using approximate Bayesian computations for drawing statistical inferences based on the results of many repeated experiments despite partially unknown collision parameters that vary between experiments. As a proof-of-principle, we consider the problem of inferring the effective mass change due to coupling with the strong-field environment.

Commercializing biomedical discoveries is a challenging process for many reasons. However, Academic Medical Centers (AMC) that have teaching, patient care, research, and service engrained in their mission are well poised to host these discoveries. These academic discoveries can lead to improvement in patient health and economic development if supported to cross the “valley of death” through institutional assistance, by providing guidance, gap funding and product development expertise. Colorado has a vibrant local startup ecosystem, state support for commercialization and entrepreneurship as well as critical mass of product development expertise. University of Colorado Anschutz Medical Campus, as a major AMC, is an engine for growth for the region. This article discusses innovation efforts at the University of Colorado Anschutz Medical Campus as a case study, which is built around two major efforts: the CCTSI and CU Innovations. I-Corps at CCTSI and the SPARK|REACH program of CU Innovations have been instrumental in fostering innovation, commercialization, and entrepreneurship on the campus.

The luminescence spectra of noble gases and their binary mixtures were measured using heavy ion beam excitation from a DC-60 accelerator. Spectra were measured in the range of 200–975 nm; the gas spectra were dominated by lines of p–s and d–p atomic transitions; in neon and argon, lines from atomic oxygen, N2, N2 +, and OH radical bands were also observed. The ultraviolet region of the spectra was represented by a “third continuum” of noble gases. In krypton, the band of the KrO excimer molecule with a maximum at 557 nm was also observed. The maxima of the heteronuclear ionic molecules bands were located at wavelengths of 329 and 506 nm (Ar–Xe), 491 nm (Kr–Xe), and 642 nm (Ar–Kr). The relative intensities of the 2p–1s transitions of the noble gases atoms were measured and are discussed.

This paper presents the results of a statistical and correlation analysis of the energy and energy density of an ion beam formed by a self-magnetically insulated diode with an explosive emission cathode. The experiments were carried out with the TEMP-4M accelerator operating in double-pulse mode: plasma formation occurs during the first pulse (negative polarity, 300–500 ns, 100–150 kV), and ion extraction and acceleration during the second pulse (positive polarity, 120 ns, 250–300 kV). Various arrangements of diodes have been investigated: strip focusing and planar diodes, a conical focusing diode and a spiral diode. The total ion beam energy was measured using both a calorimeter and an infrared camera and the beam energy density was measured by the thermal imaging and acoustic diagnostics. The correlation analysis showed that ion current density is only weakly dependent on the accelerating voltage and other output parameters of the accelerator, with the coefficient of determination <0.3. At the same time, in this paper, we have identified that the total energy of the beam and the energy density is strongly dependant on the accelerator output parameters, since the coefficient of determination >0.9. The mechanism governing stabilization of the beam energy density from shot to shot was discovered and attributed to formation of the neutral component in ion beam as being due to charge exchange between accelerated ions and neutral molecules from a neutral layer near the anode surface. Implementation using a self-magnetically insulated diode with an explosive-emission cathode, having an operational lifetime of up to 106 shots, has promising prospects for various technological applications.

Dans le but d’obtenir le déclassement de l’installation nucléaire de base 106 (INB 106),trois de ses accélérateurs ont été arrêtés puis démantelés et un autre modifié pour passersous le seuil de classement INB. Le démantèlement a été mené sur la base d’une stratégiede démontage mécanique sans découpe. Les éléments de génie civil peu activés ont pour latrès grande majorité été laissés en place sans traitement avec des mesures compensatoiresde protection du public et de l’environnement. Le résultat global de ces opérations est ungain en termes de coût et de délais et une importante diminution des risques notammentradiologiques, l’impact du site à l’état final restant acceptable.

This article presents the results of a study on transportation of a pulse ion beam of gigawatt power. This beam is formed by a self-magnetically insulated diode with an explosive-emission cathode. The experiments have been performed using the TEMP-4M pulsed ion accelerator configured in double-pulse formation mode with the first negative pulse (300–500 ns, 100–150 kV), followed by the second positive pulse (150 ns, 250–300 kV). To increase the effectiveness of ion beam focusing, a metal shield is installed on a grounded electrode. Investigations are performed using a strip focusing diode, a cone diode, and a spiral diode with metal shields of different constructions. We observed that the beam diameter at the focus decreases from 60 mm (without shield) to 40–42 mm (with a shield), which leads to an increase in the energy density by a factor of 1.5–2 being 4–5 J/cm2 at the focus. We analyzed different mechanisms for ion trajectories deviation from an ideal one: Coulomb repulsion due to incomplete space charge neutralization, influence of electromagnetic fields, etc. It is found that for a strip focusing diode the concentration of low-energy electrons accompanying the ion beam exceeds the concentration of ions by 1.3–1.5 times. The use of a metal shield improves the transportation properties of the ion beam by keeping neutralizing electrons within the beam volume which ensures its space charge neutralization during the transport.

The paper presets the results of a study on a self-magnetically insulated ion diode with an explosive-emission potential electrode. The experiments have been carried out using the TEMP-4M accelerator, operating in a double-pulse mode: the first negative pulse (300–500 ns, 100–150 kV) followed by the second positive pulse (150 ns, 250–300 kV). The ion beam energy density was 0.3–2.5 J/cm2; the beam was composed from carbon ions (80–85%) and protons. We studied several geometries of the diode: planar and focusing strip arrangement, annular and spiral geometries. It was shown that during the second voltage pulse, a condition of magnetic insulation in the diode gap is fulfilled (B/Bcr ≥3). Using the new spiral geometry of the diode, it was possible to increase the efficiency of ion current generation due to the suppression of the electron component of the total diode current by increasing the electron transit time in the gap. We have increased the efficiency of carbon ion generation from 5–9% (in the planar strip diodes) up to 17–20% in the spiral diode. The spiral geometry of the diode makes it possible to increase the efficiency of C+ ion generation 25–30 times compared to the space-charge-limited current (Childe-Langmuir limit). This is more than two times higher than in other known geometries of self-magnetically insulated diodes. The spiral diode has a resource of more than 107 pulses.

An intense electron-beam accelerator, which consists of a primary storage capacitor system, a magnetic core Tesla transformer, Blumlein pulse forming line of water dielectric, and a field-emission diode, are constructed and described. The experimental results show that the output voltage of transformer is more than 740 kV, the rise time is about 5 µs, the diode voltage is about 596 kV, electron beam current is about 60 kA, the duration is about 100 ns, and the power is 36 GW when charging voltage is 40 kV. It was suitable to drive magnetically insulated transmission line oscillator. And it can be also used in materials surface modification. This accelerator is very compact and works stably and reliably.

In the tape helix slow-wave system, discontinuous dielectrics have great effects on the dispersion characteristics. In this paper, the tape helix slow-wave system, including an inner and an outer metal shield, tape helix, nylon support, and de-ionized water as filling dielectric, was analyzed. Effects of dielectric discontinuity caused by the support dielectric and filling dielectric on the dispersion characteristics were studied in detail. The dispersion relations, phase velocities, slow-wave coefficients, and electric lengths of the spatial harmonics in the system were calculated. Results showed that, if the permittivity of support dielectric was smaller than that of the filling dielectric, frequencies of the spatial harmonics in the system rose, phase velocities and slow-wave coefficients increased, the slow-wave effect of the system was weakened so that the previous electric length was shortened. The reverse condition corresponded to the reverse results, and the electromagnetic simulation also proved it. By use of the helical pulse forming line of accelerator based on the studied tape helix slow-wave system, the electric lengths of the system were tested as 188.5 ns and 200 ns in experiments where the thicknesses of nylon support were 6 mm and 3 mm, respectively. The theoretical calculation results 198 ns and 211 ns basically corresponded to experimental results, which only had relative errors as 5 and 5.5%, respectively.

In the tape helix slow-wave system, discontinuous dielectrics have great effects on the dispersion characteristics. In this paper, the tape helix slow-wave system, including an inner and an outer metal shield, tape helix, nylon support and de-ionized water as filling dielectric, was analyzed. Effects of dielectric discontinuity caused by the support dielectric and filling dielectric on the dispersion characteristics were studied in detail. The dispersion relations, phase velocities, slow-wave coefficients and electric lengths of the spatial harmonics in the system were calculated. Results showed that, if the permittivity of support dielectric was smaller than that of the filling dielectric, frequencies of the spatial harmonics in the system rose, phase velocities and slow-wave coefficients increased, the slow-wave effect of the system was weakened so that the previous electric length was shortened. The reverse condition corresponded to the reverse results, and the electromagnetic simulation also proved it. By use of the helical pulse forming line of accelerator based on the studied tape helix slow-wave system, the electric lengths of the system were tested as 188.5 ns and 200 ns in experiment when the thicknesses of nylon support were 6 mm and 3 mm, respectively. The theoretical calculation results 198 ns and 211 ns basically corresponded to experimental results, which only had relative errors as 5 and 5.5%, respectively.

In the present analysis we study the time dependent, self-consistent propagation of nonlinear electromagnetic pulses in plasmas. Interactions of the electromagnetic pulses and wakefields are fully taken into account, from which one obtains accurate information on pulse time dependent dynamics and stability. While wide pulses may or may not retain the localized shape depending on their power, narrower pulses always tend to delocalize as time evolves.

An electron-beam accelerator based on spiral water pulse forming line which consists of a primary storage capacitor system, an air core spiral strip transformer, a spiral pulse forming line of water dielectric, and a field-emission diode, is described. The experimental results showed that the diode voltage is more than 500 kV, the electron beam current of diode is about 24 kA, and the pulse duration is about 200 ns. The main parameters of the accelerator were calculated theoretically. The distributions for electrical field in the pulse forming line were obtained by the simulations. In addition, the process of the accelerator charging a spiral pulse forming line was simulated through the Pspice software to get the waveforms of charging voltage of pulse forming line, the diode voltage and diode current of accelerator. The theoretical and simulated results agree with the experimental results. This accelerator is very compact and works stably and reliably.

An electron-beam accelerator, which consists of a primary storage capacitor system, an air core spiral strip transformer, water Blumlein line of water dielectric, and a field-emission diode, is described. The experimental results show that the diode voltage is more than 400 kV, electron beam current is about 40 kA, and the pulse duration is more than 80 ns. This accelerator is very compact and works stably and reliably.

We describe the next set of experiments proposed in the U.S. Heavy Ion Fusion Virtual National Laboratory, the so-called Integrated Beam Experiment (IBX). The purpose of IBX is to investigate in an integrated manner the processes and manipulations necessary for a heavy ion fusion induction accelerator. The IBX experiment will demonstrate injection, acceleration, compression, bending, and final focus of a heavy ion beam at significant line charge density. Preliminary conceptual designs are presented and issues and trade-offs are discussed. Plans are also described for the step after IBX, the Integrated Research Experiment (IRE), which will carry out significant target experiments.

The experimental results of the activation spectra, dose rate measurements, and the residual nuclide production cross sections obtained after the irradiation of the NatCu and 59Co targets by 12C ion beams at ITEP and GSI are presented in this paper. These results are compared with simulations by the CASCADE and LAQGSM codes.