Hostname: page-component-cd9895bd7-dzt6s Total loading time: 0 Render date: 2024-12-25T02:05:06.519Z Has data issue: false hasContentIssue false

High-brightness all-fiber Raman lasers directly pumped by multimode laser diodes

Published online by Cambridge University Press:  13 March 2019

S. A. Babin*
Affiliation:
Institute of Automation and Electrometry, SB RAS, Novosibirsk 630090, Russia Novosibirsk State University, Novosibirsk 630090, Russia
*
Correspondence to:  S. A. Babin, Institute of Automation and Electrometry, SB RAS, Novosibirsk 630090, Russia. Email: [email protected]

Abstract

High-brightness fiber laser sources usually utilize active rare-earth-doped fibers cladding-pumped by multimode laser diodes (LDs), but they operate in limited wavelength ranges. Singlemode-passive-fiber based Raman lasers are able to operate at almost any wavelength being pumped by high-power fiber lasers. One of the interesting possibilities is to directly pump graded-index (GRIN) multimode passive fibers by available high-power multimode LDs at 915–940 nm, thus achieving high-power Raman lasing in the wavelength range of 950–1000 nm, which is problematic for rare-earth-doped fiber lasers. Here we review the latest results on the development of all-fiber high-brightness LD-pumped sources based on GRIN fiber with in-fiber Bragg gratings (FBGs). The mode-selection properties of FBGs inscribed by fs pulses supported by the Raman clean-up effect result in efficient conversion of multimode pump into a high-quality output beam at 9xx nm. GRIN fibers with core diameters 62.5, 85 and $100~\unicode[STIX]{x03BC}\text{m}$ are compared. Further scaling capabilities and potential applications of such sources are discussed.

Type
Research Article
Creative Commons
Creative Common License - CCCreative Common License - BY
This is an Open Access article, distributed under the terms of the Creative Commons Attribution licence (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted re-use, distribution, and reproduction in any medium, provided the original work is properly cited.
Copyright
© The Author 2019

1 Introduction

High-brightness fiber laser sources based on active rare-earth (RE)-doped fibers are characterized by excellent output characteristics and unique performance enabling their wide use for scientific and industrial applications[Reference Richardson, Nilsson and Clarkson1]. However, they operate at specific wavelengths defined by the dopant gain bandwidth that limits their application range. Singlemode-passive-fiber based Raman lasers are able to operate at almost any wavelength defined by the pump wavelength, Stokes shift and number of cascades at Raman conversion[Reference Dianov and Prokhorov2]. Raman fiber lasers (RFLs) are usually pumped into the singlemode-passive-fiber core by RE-doped fiber lasers operating in singlemode regime with fundamental transverse mode output. Using for pumping the most powerful Yb-doped fiber laser (YDFL) operating around $1~\unicode[STIX]{x03BC}\text{m}$ , it is possible to obtain Raman lasing almost in the whole transmission window of silica fibers $(1{-}2~\unicode[STIX]{x03BC}\text{m})$ , thanks to the efficient cascaded generation of higher-order Stokes components. In their turn, high-power RE-doped fiber lasers are usually cladding-pumped by multimode (MM) laser diodes (LDs). Such a complex pumping scheme leads to a rather complicated design of RFLs. An interesting possibility to simplify the RFL design is its direct pumping by cheap and reliable high-power MM LDs, similar to the LD-pumped RE-doped fiber lasers[Reference Richardson, Nilsson and Clarkson1]. Though it is possible to employ cladding pumping, this technique requires the development of special double-clad passive fibers. In this way, Raman lasing at 1120 nm with output power of 100 W and beam-quality parameter $M^{2}\sim 1.6$ was demonstrated with an MM YDFL as a pump source[Reference Codemard, Ji, Sahu and Nilsson3], whereas at direct diode pumping only 6 W output power was obtained by the same group[Reference Yao, Harish, Sahu and Nilsson4].

From technical and economical points of view, it is attractive to use standard graded-index (GRIN) MM fibers which are widely used in telecom. In this case, one can directly couple the MM radiation of high-power LDs into the MM GRIN-fiber core. In addition, using commercially available MM LDs with operating wavelengths of 915–940 nm, it is possible to obtain high-power Raman lasing in the wavelength range of 950–1000 nm, which is problematic for RE-doped fiber lasers. At the same time, output beam quality of the MM RFL may be high enough due to the beam clean-up effect at Raman conversion of continuous wave (CW) radiation in GRIN fibers[Reference Baek and Roh5, Reference Terry, Alley and Russell6]. Since the power of commercial 9xx-nm LDs exceeds 100 W level for a single unit pigtailed by a 105- $\unicode[STIX]{x03BC}$ m core fiber, the MM RFL with direct LD pumping became feasible.

The concept of LD-pumped GRIN-fiber based RFLs has been developed in two different directions. First direction continues the study initiated in Ref. [Reference Baek and Roh5] with a focus on the opportunities of high-quality beam generation using fiber Bragg gratings (FBGs) as cavity mirrors[Reference Kablukov, Dontsova, Zlobina, Nemov, Vlasov and Babin7Reference Zlobina, Kablukov, Wolf, Dostovalov and Babin10], whereas second one aims at high-power capabilities based on free-space pump coupling and bulk mirrors cavity[Reference Yao, Harish, Sahu and Nilsson4, Reference Glick, Fromzel, Zhang, Dahan, Ter-Gabrielyan, Pattnaik and Dubinskii11, Reference Glick, Fromzel, Zhang, Ter-Gabrielyan and Dubinskii12]. In the last case, up to 154 W power is obtained at ${\sim}1020~\text{nm}$ [Reference Glick, Fromzel, Zhang, Ter-Gabrielyan and Dubinskii12], but Raman output at this wavelength is not as interesting, because higher power and narrower linewidth are available from YDFLs[Reference Glick, Sintov, Zuitlin, Pearl, Shamir, Feldman, Horvitz and Shafir13, Reference Jiang, Zhou, Xiao and Ma14]. In addition, in spite of significant improvement of the output beam quality $(M^{2}=4{-}8)$ in comparison with that for the pump beam $(M^{2}\sim 20)$ due to the Raman clean-up effect in GRIN fibers, it is far from singlemode regime.

The first experiments with a cavity FBG UV-inscribed in telecom GRIN fiber of 62.5- $\unicode[STIX]{x03BC}\text{m}$ core pumped by a 940-nm MM LD resulted in ${\sim}3~\text{W}$ 980-nm output of much better beam quality generated with Fresnel reflection at the output end[Reference Kablukov, Dontsova, Zlobina, Nemov, Vlasov and Babin7]. Using angled cleaving of the output fiber end, random lasing in half-open cavity of such LD-pumped GRIN-fiber lasers has been also demonstrated[Reference Babin, Dontsova and Kablukov8]. As a next step, a 915-nm LD pumping of a 62.5- $\unicode[STIX]{x03BC}\text{m}$ GRIN fiber with two UV-inscribed FBGs (highly reflective and output one) enabled generation of 954-nm Stokes radiation[Reference Zlobina, Kablukov, Skvortsov, Nemov and Babin9]. Implementation of a special output FBG inscribed by a point-by-point femtosecond (fs) technique in the central part $(1\times 10~\unicode[STIX]{x03BC}\text{m})$ of the 62.5- $\unicode[STIX]{x03BC}\text{m}$ GRIN-fiber core resulted in Raman lasing with output power of 10 W at 954 nm in nearly singlemode $(M^{2}\sim 1.2)$ [Reference Zlobina, Kablukov, Wolf, Dostovalov and Babin10], due to the mode-selective properties of such FBG.

Here we review our recent results on the development of simple and reliable all-fiber configuration of such RFL having high beam quality and high power simultaneously, due to the fiber coupling of several LDs enabling high-power pumping of a GRIN fiber and FBGs with special 3D structure featured by mode-selective properties. GRIN fibers with core diameters 62.5, 85 and $100~\unicode[STIX]{x03BC}\text{m}$ are compared. Further scaling capabilities and potential applications of such sources are discussed.

2 Experimental scheme and operating principles

Experimental scheme of the studied LD-pumped MM GRIN-fiber RFL is shown in Figure 1. Instead of a bulk-optics scheme (shown in the dashed box) for coupling of LD pump radiation to the GRIN-fiber core used in the first experiments[Reference Kablukov, Dontsova, Zlobina, Nemov, Vlasov and Babin7Reference Zlobina, Kablukov, Wolf, Dostovalov and Babin10], we implemented a fiber coupling scheme based on a fusion spliced combiner for 3 LDs with GRIN-fiber output port of $100~\unicode[STIX]{x03BC}\text{m}$ core diameter[Reference Zlobina, Kablukov, Wolf, Nemov, Dostovalov, Tyrtyshnyy, Myasnikov and Babin15]. Coupling of several diodes (LD1–LD3) through the MM fiber pump combiner directly to the Raman GRIN fiber allows one to increase the pump power. In addition, using the Raman GRIN fiber of larger-core diameter results in sufficient reduction of pump coupling losses. In-fiber gratings UV-FBG1 and fs-FBG2 are inscribed in the studied Raman GRIN fiber by ultraviolet- and femtosecond-FBG fabrication technologies, respectively; see Refs. [Reference Zlobina, Kablukov, Wolf, Dostovalov and Babin10, Reference Zlobina, Kablukov, Wolf, Nemov, Dostovalov, Tyrtyshnyy, Myasnikov and Babin15] for details. The obtained all-fiber configuration has obvious advantages such as compactness, ease of operation, low cost, reliability, long-term stability in combination with flexibility of the output fiber end. Output beam consisted of the Stokes and transmitted pump radiation split by dichroic mirrors M1–M3 is analyzed by means of power meters (P1, P2) and optical spectrum analyzer replaced by Thorlabs $M^{2}$ -meter for beam-quality measurements.

Figure 1. All-fiber scheme of MM GRIN-fiber Raman laser with cavity formed by HR UV-FBG1 and output fs-FBG2 with LD pumping through the fiber pump combiner (or bulk-optic pump coupling scheme[Reference Zlobina, Kablukov, Wolf, Dostovalov and Babin10] shown in the inset).

A comparison of the 1.1 km 62.5- $\unicode[STIX]{x03BC}\text{m}$ GRIN RFL with pump coupling via fiber spliced combiner[Reference Zlobina, Kablukov, Wolf, Nemov, Dostovalov, Tyrtyshnyy, Myasnikov and Babin15] and that one with bulk optics[Reference Zlobina, Kablukov, Wolf, Dostovalov and Babin10] has shown that the generation threshold increases from ${\sim}40~\text{W}$ (bulk optics) to ${\sim}50~\text{W}$ (all-fiber). At the same time, the RFL efficiency and maximum Stokes power at 954 nm also increase (40 to 47% and 10 to 18 W, respectively) after the implementation of fiber coupling which eliminates reflection from the input fiber facet thus increasing the threshold for the 2nd Stokes wave.

Then we tested the developed all-fiber MM RFL scheme with the use of GRIN Raman fiber of different core diameters: 62.5, 85[Reference Zlobina, Kablukov, Wolf, Nemov, Dostovalov, Tyrtyshnyy, Myasnikov and Babin15] and 100[Reference Evmenova, Kablukov, Nemov, Wolf, Dostovalov, Tyrtyshnyy, Myasnikov and Babin16] $\unicode[STIX]{x03BC}\text{m}$ , in which corresponding highly reflective (HR) UV-FBG1 and output fs-FBG2 have been fabricated. The point-by-point fs inscription technology based on nonlinear (multi-photon) mechanism of refractive index change enables modification of a small area near the center of GRIN-fiber core, and therefore an output coupler made by this technology preferably reflects the fundamental transverse mode. At the same time, HR FBG made by this technology has high losses, which is why we used UV-inscribed HR FBGs with relatively low losses. The measured FBG spectra in different GRIN fibers are compared in Figure 2. One can see that for all fs-FBGs the maximum reflection is provided for the longer-wavelength peak corresponding to the fundamental transverse mode. The periodic short-wavelength resonances correspond to the FBG coupling with different groups of higher-order modes. The spectral separation between the groups decreases with increasing core diameter (amounting to about 0.6, 0.5 and 0.4 nm for 62.5, 85 and $100~\unicode[STIX]{x03BC}\text{m}$ core, respectively) in correspondence with the well-known formula[Reference Mizunami, Djambova, Niiho and Gupta17]

(1) $$\begin{eqnarray}\unicode[STIX]{x0394}\unicode[STIX]{x1D706}=\unicode[STIX]{x1D706}^{2}\cdot \mathit{NA}/(\unicode[STIX]{x1D70B}\,dn_{1}^{2}),\end{eqnarray}$$

where $\unicode[STIX]{x1D706}$ is the wavelength of fundamental mode, NA is numerical aperture, $d$ is the core diameter, and $n_{1}$ is the refractive index of cladding. It should be also noted that HR UV-FBGs have rather smooth profile with strongly overlapping mode resonances, whereas output fs-FBG has clear resonant structure with sufficient discrimination of higher-order modes (about $-10~\text{dB}$ for all core diameters) relative to the fundamental mode peak. These features of cavity FBGs enable efficient fundamental mode selection in MM GRIN-fiber RFLs at relatively low transmission of generated Stokes power toward the pump LDs.

Figure 2. Comparison of HR UV-FBG and output fs-FBG inscribed in GRIN fibers of different core diameters: (a) $62.5~\unicode[STIX]{x03BC}\text{m}$ [Reference Zlobina, Kablukov, Wolf, Dostovalov and Babin10], (b) $85~\unicode[STIX]{x03BC}\text{m}$ [Reference Zlobina, Kablukov, Wolf, Nemov, Dostovalov, Tyrtyshnyy, Myasnikov and Babin15] and (c)  $100~\unicode[STIX]{x03BC}\text{m}$ [Reference Evmenova, Kablukov, Nemov, Wolf, Dostovalov, Tyrtyshnyy, Myasnikov and Babin16].

Figure 3. (a) Output Stokes power at 954 nm (filled symbols) as a function of input (coupled to GRIN fiber) LD pump power and (b) corresponding beam-quality parameter $M^{2}$ as a function of Stokes power for different GRIN-fiber core diameters. Arrows mark the threshold of the 2nd-order Stokes wave generation at 996 nm.

Power, spectral and beam-quality characteristics of the generated Stokes radiation at 954 nm have been measured and compared for different Raman GRIN fibers keeping the same three 915-nm pump LDs and the same pump combiner (of $100~\unicode[STIX]{x03BC}\text{m}$ core). Note that the pump coupling losses are reduced with the increasing core diameter of the Raman GRIN fiber amounting to about 75%, 50% and 25% for 62.5, 85 and $100~\unicode[STIX]{x03BC}\text{m}$ core, respectively, thus increasing the available coupled pump power.

Figure 4. (a) Output spectra for GRIN-fiber Raman laser with 62.5, 85 and $100~\unicode[STIX]{x03BC}\text{m}$ cores at different Stokes powers. (b) Corresponding $-3~\text{dB}$ linewidth as a function of the generated Stokes power at 954 nm fitted by curves ${\sim}x^{a}$ with best-fit parameter $a=0.64$ ( $62.5~\unicode[STIX]{x03BC}\text{m}$ ); 0.45 ( $85~\unicode[STIX]{x03BC}\text{m}$ ); 0.34 ( $100~\unicode[STIX]{x03BC}\text{m}$ ).

3 Raman lasing in GRIN fibers of different core diameters

The output power at 954 nm as a function of input (coupled to the Raman fiber) pump power in different GRIN fibers of optimal length is shown in Figure 3 together with the measured beam-quality parameter $M^{2}$ for the generated Stokes beam.

Optimal Raman fiber length is defined by the 2nd Stokes threshold and the available pump power from the same three 915-nm LDs given that the losses at pump coupling to the Raman fiber decrease with its increasing core diameter. So, the maximum input pump power is about 90, 180 and 240 W for 62.5, 85 and $100~\unicode[STIX]{x03BC}\text{m}$ GRIN fibers, respectively. As the 2nd Stokes threshold can be shifted to higher powers by shortening GRIN fiber, we made it so that the 2nd Stokes threshold (marked by arrow in Figure 3(a)) becomes closer to the maximum input pump power. This gives the value of optimal length appearing to be nearly the same for all core diameters of GRIN fiber. At the optimal length, the output Stokes powers (and slope efficiency for conversion of input pump to Stokes output power) take their maximum values at the available pump power, amounting to about 18, 49 and 62 W (and 47%, 67% and 84%), respectively; see Figure 3(a). Herewith, the measured beam-quality parameter $M^{2}$ slightly worsens with increasing core diameter amounting to about 1.3, 2.5 and 3 for the tested GRIN fibers; see Figure 3(b). Detailed measurements of beam quality for 100- $\unicode[STIX]{x03BC}\text{m}$ GRIN fiber by fitting of the focused beam waist shape show that it is nearly the same for x and y beam axes (solid and empty symbols) and is only slightly varying in the range $M^{2}=2.5{-}3.2$ with increasing output power from ${\sim}10$ to ${\sim}60~\text{W}$ . At that, the measured quality parameter for the pump radiation at maximum power amounts to $M^{2}\sim 32$ (the quality worsens after pump combiner). It means that the brightness defined as

(2) $$\begin{eqnarray}B=P/(M^{2}\unicode[STIX]{x1D706})^{2}\end{eqnarray}$$

is enhanced for the Raman output beam as compared to the input pump beam by ${\sim}20$ times due to the joint action of Raman beam clean-up effect and mode-selective properties of cavity FBGs. The enhancement factor related to the coupled pump power is nearly the same for all GRIN fibers, but with an account for the pump coupling efficiency the larger-core GRIN fibers are more suitable for the development of high-brightness high-power sources at 9xx nm. Note that the transmitted LD pump power at the maximum generated Stokes power is nearly the same (30–40 W) for all fibers that also makes larger-core GRIN fibers more preferable for LD brightness enhancement.

Figure 5. (a) Stable and unstable beam profiles at low power (13 W) for operation at 950 nm (left) and 958 nm (right) in 100- $\unicode[STIX]{x03BC}\text{m}$ GRIN RFL, respectively. (b) Measured Raman gain profile with corresponding marks illustrating 100- $\unicode[STIX]{x03BC}\text{m}$ GRIN RFL operation with 950-, 954- and 958-nm FBGs[Reference Evmenova, Kablukov, Nemov, Wolf, Dostovalov, Tyrtyshnyy, Myasnikov and Babin16].

The measured Stokes spectrum for all GRIN fibers has a shape close to the hyperbolic secant with exponential wings (see Figure 4(a)), just like the spectrum of conventional Raman lasers based on singlemode fibers[Reference Babin, Churkin, Ismagulov, Kablukov and Podivilov18]. The only sign of higher-order transverse mode impurities consists in visible asymmetry of the spectral profile that is more pronounced for 85- and 100- $\unicode[STIX]{x03BC}\text{m}$ GRIN fibers in correspondence with the beam-quality data (Figure 3(b)). The width of the generated spectrum is defined by the reflection spectrum of cavity FBG (Figure 2) and nonlinear-optical effects resulting in its power broadening. The extracted $-3~\text{dB}$ linewidth grows with increasing power nonlinearly reaching nearly the same value for three core sizes, but at sufficiently different Stokes powers. Taking that the power broadening is defined by the effect of self-phase modulation (SPM) that is proportional to the laser beam intensity, this means that the effective beam area is sufficiently larger in larger-core GRIN fibers. An additional effect reducing the RFL linewidth is the group velocity dispersion (GVD) in relation to the nonlinear effects (SPM, Raman gain). If its relative contribution increases, the power low changes from linear to nonlinear one with a cubic root law in the limiting case of strong dispersion (see Ref. [Reference Babin, Zlobina, Kablukov and Podivilov19] and citation therein). In case of GRIN fibers with different cores, the degree of the root law $x^{a}$ amounts to $a=0.64$ , 0.45 and 0.34 for 62.5, 85 and 100- $\unicode[STIX]{x03BC}\text{m}$ fibers, respectively, thus confirming increasing role of GVD in larger-core GRIN fibers.

It should be also noted that the $-3~\text{dB}$ linewidth remains to be smaller than the corresponding distance between the neighboring groups of transverse modes of GRIN fiber. Besides, in case of 100- $\unicode[STIX]{x03BC}\text{m}$ GRIN fiber the laser spectrum becomes unstable at low powers, but stabilizes at high powers (quite opposite to the mode instability effect in RE-doped fiber lasers[Reference Jauregui, Limpert and Tünnermann20]). At that, both the spectral (Figure 4(a), lower picture) and spatial (Figure 5(a)) profiles exhibit the signs of high-order transverse mode appearance time to time, while at high powers the profiles are stable consisting of constant group of low-order modes with the main contribution from the fundamental modes, just like for smaller-core GRIN fibers in a broad range of powers.

Figure 6. (a) Output power and (b) beam-quality characteristics of 2nd-order random Raman lasing at 996 nm in 100- $\unicode[STIX]{x03BC}\text{m}$ GRIN RFL together with power of the 1st Stokes output at 954 nm.

To clarify the mechanism of the low-power mode instability in 100- $\unicode[STIX]{x03BC}\text{m}$ GRIN fiber, Raman generation with FBGs centered at 950 nm and 958 nm (slightly shifted from the Raman gain maximum to the short and to the long wavelengths, respectively) was tested in Ref. [Reference Evmenova, Kablukov, Nemov, Wolf, Dostovalov, Tyrtyshnyy, Myasnikov and Babin16]. It has been found that the unstable behavior with random appearance of high-order transverse modes is observed in different power domains for different generation lines. The spectrum stabilizes at ${>}$ 35 W for 958 nm, at ${>}$ 18 W for 954 nm and at ${>}$ 8 W for 950 nm, thus demonstrating that the transverse mode competition depends on the FBG wavelength position within the Raman gain spectral profile (Figure 5(b)). The weakest instability effect is observed at the short-wavelength slope of Raman gain at 950-nm operation when the gain coefficient for higher-order modes is lower than that for the fundamental one. Note that the Raman shift between LD and FBG wavelengths slightly decreases with increasing LD power which experience “red” wavelength shift at high powers.

4 Random Raman lasing in GRIN fibers

As shown in the previous section, 2nd-order Stokes wave generation threshold due to the random distributed feedback via Rayleigh backscattering along the GRIN fiber (and probably some reflection from splice points, etc.) limits the maximum power of the 1st Stokes Raman lasing. This limitation may be moved to higher powers by shortening the fiber accompanied by corresponding increase of the coupled pump power and/or by inserting additional losses for the 2nd Stokes wave, similar to singlemode fibers[Reference Song, Xu, Ye, Wu, Zhang, Xu and Zhou21].

However, cascaded generation of the 2nd Stokes order may be treated not only as a limiting effect, but also as an opportunity to obtain new laser wavelengths, similarly to cascaded random lasing in singlemode fibers[Reference Babin, Zlobina, Kablukov and Podivilov19]. In GRIN fibers this regime is also interesting from the point of further beam-quality improvement. Such experiments have been performed by using an additional input HR FBG at 996 nm inserted in the scheme of Figure 1, thus forming a half-open cavity with random distributed feedback for the 2nd Stokes wave. At that, the 1st Stokes wave generated in normal FBG cavity at 954 nm serves as a pump for that. The obtained 2nd Stokes output power at 996 nm is shown in Figure 6(a) together with the 1st Stokes power as a function of input LD pump power. After the 2nd threshold pump power of ${\sim}160~\text{W}$ , the measured output power at 996 nm selected by additional dichroic mirror grows rapidly with an average slope of about 70% that is nearly the same as that for the 1st Stokes wave (before the 2nd Stokes threshold). Maximum power at 996 nm amounts to 27 W. At the same time, the beam quality for random lasing at 996 nm appears to be sufficiently better than that at 954 nm amounting to about $M^{2}\sim 1.6$ without significant changes in all power range. So, random distributed feedback additionally improves the beam quality, as it was also mentioned at low-power 1st Stokes random lasing[Reference Babin, Dontsova and Kablukov8]. This effect may be explained by stronger Rayleigh-backscattering feedback for the fundamental transverse mode, improving its selection in addition to the effects of Raman beam clean-up and mode-selective FBGs. It appears also possible to obtain random lasing at significantly shifted wavelength (978 nm) with relatively good parameters, which are measured to be much better than the normal 2nd-order Raman lasing in the linear cavity formed by two FBGs; for more details of this study, see Ref. [Reference Evmenova, Kuznetsov, Nemov, Wolf, Dostovalov, Kablukov and Babin22]. The obtained high beam quality made it possible to realize efficient frequency doubling in PPLN nonlinear crystal, thus generating blue laser light near 489 nm; the details of this study will be published elsewhere.

5 Conclusion

Thus, we have demonstrated possibilities to develop high-brightness 9xx-nm fiber sources based on the passive MM GRIN fiber directly pumped by high-power MM LDs. All-fiber configuration of such diode-pumped RFL is shown to be possible with the use of FBGs inscribed in the MM GRIN-fiber core and LD coupling via spliced fiber pump combiner. It has been demonstrated that the mode-selection properties of FBGs inscribed by fs pulses in the central part of fiber core (supported by the Raman clean-up effect) result in efficient conversion of MM LD pump radiation coupled to the fiber $(M^{2}\sim 30)$ into a high-quality output beam at 9xx nm with brightness enhancement factor of about 20. GRIN fibers with core diameters 62.5, 85 and $100~\unicode[STIX]{x03BC}\text{m}$ have been compared. With the core enlargement, the pump to Stokes conversion efficiency increases from 47% to 84% at the expense of slight enlargement of beam-quality parameter $M^{2}$ (from 1.3 to ${\sim}3$ ). At that, maximum output power at 954 nm amounts to 18, 49 and 62 W for 62.5, 85 and $100~\unicode[STIX]{x03BC}\text{m}$ GRIN fiber, respectively, pumped by the same 915-nm LDs. The maximum power is defined by the losses at fiber coupling of LDs to corresponding GRIN fiber being lower for larger-core fibers. The laser linewidth appears to be nearly the same $({\sim}0.4~\text{nm})$ for all GRIN fibers at corresponding maximum output power that is reasoned by increasing effective beam area in larger-core fibers. It has been also observed that the beam quality and spectral width are only weakly varying in the broad range of powers (10–60 W for 100- $\unicode[STIX]{x03BC}\text{m}$ fiber), thus indicating the formation of stable group of coupled low-order modes. At that, the power broadening law becomes close to cubic root with increasing core diameter (power degree decreases from 0.64 to 0.34), thus indicating increasing role of GVD in larger-core GRIN fibers. Experiments on 2nd-order random lasing at 996 and 978 nm and second harmonic generation have been also endeavored, which demonstrate a possibility to generate new laser wavelengths with improved beam quality in the developed RFL scheme.

Note that these are only the first steps demonstrating basic principles of the new type of CW high-power fiber laser. The next steps toward a better pump coupling at higher powers and a better fundamental mode selection will result in further improvements in optical efficiency, output power and brightness of such sources. This makes it very attractive for applications, such as efficient/bright source for pumping solid-state/fiber lasers, second harmonic generation with generation of visible light and corresponding application for laser displays and bio-medical imaging. Interesting fundamental challenges also appear, e.g., investigation of mode instability in passive GRIN fibers, which may behave differently from that in step-index active fibers, thus breaking the existing limits of high-power fiber lasers.

Acknowledgements

The author acknowledges financial support of Russian Science Foundation (grant 14-22-00118) and valuable assistance of S. I. Kablukov, E. A. Evmenova, A. G. Kuznetsov, A. Wolf and S. R. Abdullina during the preparation of this paper.

References

Richardson, D. J. Nilsson, J. and Clarkson, W. A. J. Opt. Soc. Am. B 27, B63 (2010).Google Scholar
Dianov, E. M. and Prokhorov, A. M. J. Sel. Top. Quantum Electron. 6, 1022 (2000).Google Scholar
Codemard, C. A. Ji, J. Sahu, J. K. and Nilsson, J. Proc. SPIE 7508, 75801N (2010).Google Scholar
Yao, T. Harish, A. V. Sahu, J. K. and Nilsson, J. Appl. Sci. 5, 1323 (2015).Google Scholar
Baek, S. H. and Roh, W. Opt. Lett. 29, 153 (2004).Google Scholar
Terry, N. B. Alley, T. G. and Russell, T. H. Opt. Express 15, 17509 (2007).Google Scholar
Kablukov, S. I. Dontsova, E. I. Zlobina, E. A. Nemov, I. N. Vlasov, A. A. and Babin, S. A. Laser Phys. Lett. 10, 085103 (2013).Google Scholar
Babin, S. A. Dontsova, E. I. and Kablukov, S. I. Opt. Lett. 38, 3301 (2013).Google Scholar
Zlobina, E. A. Kablukov, S. I. Skvortsov, M. I. Nemov, I. N. and Babin, S. A. Laser Phys. Lett. 13, 035102 (2016).Google Scholar
Zlobina, E. A. Kablukov, S. I. Wolf, A. A. Dostovalov, A. V. and Babin, S. A. Opt. Lett. 42, 9 (2017).Google Scholar
Glick, Y. Fromzel, V. Zhang, J. Dahan, A. Ter-Gabrielyan, N. Pattnaik, R. K. and Dubinskii, M. Laser Phys. Lett. 13, 065101 (2016).Google Scholar
Glick, Y. Fromzel, V. Zhang, J. Ter-Gabrielyan, N. and Dubinskii, M. Appl. Opt. 56, B97 (2017).Google Scholar
Glick, Y. Sintov, Y. Zuitlin, R. Pearl, S. Shamir, Y. Feldman, R. Horvitz, Z. and Shafir, N. J. Opt. Soc. Am. B 33, 1392 (2016).Google Scholar
Jiang, M. Zhou, P. Xiao, H. and Ma, P. High Power Laser Sci. Eng. 3, e25 (2015).Google Scholar
Zlobina, E. A. Kablukov, S. I. Wolf, A. A. Nemov, I. N. Dostovalov, A. V. Tyrtyshnyy, V. A. Myasnikov, D. V. and Babin, S. A. Opt. Express 25, 12581 (2017).Google Scholar
Evmenova, E. A. Kablukov, S. I. Nemov, I. N. Wolf, A. A. Dostovalov, A. V. Tyrtyshnyy, V. A. Myasnikov, D. V. and Babin, S. A. Laser Phys. Lett. 15, 095101 (2018).Google Scholar
Mizunami, T. Djambova, T. V. Niiho, T. and Gupta, S. J. Lightwave Technol. 18, 230 (2000).Google Scholar
Babin, S. A. Churkin, D. V. Ismagulov, A. E. Kablukov, S. I. and Podivilov, E. V. J. Opt. Soc. Am. B 24, 1729 (2007).Google Scholar
Babin, S. A. Zlobina, E. A. Kablukov, S. I. and Podivilov, E. V. Sci. Rep. 6, 22625 (2016).Google Scholar
Jauregui, C. Limpert, J. and Tünnermann, A. Nat. Photon. 7, 861 (2013).Google Scholar
Song, J. Xu, H. Ye, J. Wu, H. Zhang, H. Xu, J. and Zhou, P. Sci. Rep. 8, 10942 (2018).Google Scholar
Evmenova, E. A. Kuznetsov, A. G. Nemov, I. N. Wolf, A. A. Dostovalov, A. V. Kablukov, S. I. and Babin, S. A. Sci. Rep. 8, 17495 (2018).Google Scholar
Figure 0

Figure 1. All-fiber scheme of MM GRIN-fiber Raman laser with cavity formed by HR UV-FBG1 and output fs-FBG2 with LD pumping through the fiber pump combiner (or bulk-optic pump coupling scheme[10] shown in the inset).

Figure 1

Figure 2. Comparison of HR UV-FBG and output fs-FBG inscribed in GRIN fibers of different core diameters: (a) $62.5~\unicode[STIX]{x03BC}\text{m}$[10], (b) $85~\unicode[STIX]{x03BC}\text{m}$[15] and (c) $100~\unicode[STIX]{x03BC}\text{m}$[16].

Figure 2

Figure 3. (a) Output Stokes power at 954 nm (filled symbols) as a function of input (coupled to GRIN fiber) LD pump power and (b) corresponding beam-quality parameter $M^{2}$ as a function of Stokes power for different GRIN-fiber core diameters. Arrows mark the threshold of the 2nd-order Stokes wave generation at 996 nm.

Figure 3

Figure 4. (a) Output spectra for GRIN-fiber Raman laser with 62.5, 85 and $100~\unicode[STIX]{x03BC}\text{m}$ cores at different Stokes powers. (b) Corresponding $-3~\text{dB}$ linewidth as a function of the generated Stokes power at 954 nm fitted by curves ${\sim}x^{a}$ with best-fit parameter $a=0.64$ ($62.5~\unicode[STIX]{x03BC}\text{m}$); 0.45 ($85~\unicode[STIX]{x03BC}\text{m}$); 0.34 ($100~\unicode[STIX]{x03BC}\text{m}$).

Figure 4

Figure 5. (a) Stable and unstable beam profiles at low power (13 W) for operation at 950 nm (left) and 958 nm (right) in 100-$\unicode[STIX]{x03BC}\text{m}$ GRIN RFL, respectively. (b) Measured Raman gain profile with corresponding marks illustrating 100-$\unicode[STIX]{x03BC}\text{m}$ GRIN RFL operation with 950-, 954- and 958-nm FBGs[16].

Figure 5

Figure 6. (a) Output power and (b) beam-quality characteristics of 2nd-order random Raman lasing at 996 nm in 100-$\unicode[STIX]{x03BC}\text{m}$ GRIN RFL together with power of the 1st Stokes output at 954 nm.