This paper presents a new topology for a microwave active mixer using compact microstrip diplexer constituted from two dual-mode open loop resonators. The resonators are tuned to the radio frequency (RF) and local-oscillator (LO) frequencies, respectively, to effectively isolate the two input signals, while the diplexer output port is connected to the gate circuit of a commercial low cost GaAs pHEMT transistor. The drain circuit of the active device is connected to the load via an intermediate-frequency (IF)-modified Chebyshev low-pass filter to remove the unwanted RF and LO signals and reduce other spurious frequencies at the output of the mixer circuit. The circuit has been designed and constructed for an RF of 850 MHz, LO frequency of 1050 MHz, and an IF of 200 MHz. Experimental measurements show that the circuit provides a conversion gain of 18 dB at LO drive power of +2 dBm. It also operates satisfactorily over the RF range from 800 to 900 MHz with good image frequency rejection and stable operation.

This paper presents the radio frequency (RF) design and experimental validation of a multifunctional bandpass filtering (BPF) concept with center frequency tunability and RF codesigned isolator and impedance matching functionality. The multifunctional bandpass filter/isolator (BPFI) concept combines frequency-tunable reciprocal resonators and nonreciprocal frequency-selective stages (NFSs) to realize center frequency tunability and fully directional transfer characteristics. The NFS, as the core component of the BPFI concept, exhibits frequency-selective transmission response in the forward direction and signal cancellation in the reverse direction. Its tunability is achieved by combining a transistor-based network with a tunable capacitively loaded coupled-line section. Furthermore, the NFS facilitates matching of different source loads allowing for the BPFIs to be used as reconfigurable matching networks. For experimental validation, an NFS and two BPFIs were designed, manufactured, and measured at L band. Their features include (i) NFS: center frequency tuning from 1.55 to 1.9 GHz with maximum directivity from 20 to 52 dB and gain from 0.3 to 1.3 dB. (ii) BPFI (topology A): center frequency tuning from 1.52 to 1.9 GHz with maximum directivity from 20 to 44 dB and gain from −1.5 to −0.5 dB. (iii) BPFI (topology C): ability to match complex loads with 26 + j18 Ω and 26 − j14 Ω.

We report on the successful implementation of a photonic-based beam steering approach for point-to-multipoint terahertz (THz) communications. The frequency-agile radiation properties of a THz leaky-wave antenna connected to a photodiode are utilized in the remote transmitter for generating multiple individually steerable THz beams. The approach benefits from the ultra-wide frequency tunability of optical heterodyne systems for frequency-agile THz beam steering. Moreover, the approach allows to exploit high performance and mature optical modulation techniques for generating THz beams with a high data capacity. In the THz receiver, a carrier frequency insensitive envelope THz detector based upon a single Schottky-barrier diode is used. In detail, THz communications in the 300 GHz band (WR3.4) with a maximum steering angle up to 90° is reported. Experimentally, for single steerable THz beam operation, a record high data rate of 35 Gbit/s at a wireless distance of 30 cm is achieved using two-level pulse amplitude modulation. Also, longer wireless distances up to 110 cm with 5 Gbit/s are demonstrated. Furthermore, point-to-multipoint THz communications is reported using two individually steerable THz beams carrying 10 Gbit/s and 5 Gbit/s over 70 cm and 50 cm, respectively.

An isolated low-profile multilayer all-ports-matched broadside-coupled balun (BCB) with arbitrary isolation bandwidth is presented. Analytical relations are derived and provided for the isolation circuit (IC) design in terms of electrical and physical parameters. Accordingly, instructions are given on obtaining optimum bandwidth and isolation responses for the IC. Design procedure for the BCB is presented together with a case study for power amplifier application. The BCB is validated theoretically, analytically, and experimentally, and results are in good agreement. The fabricated balun has insertion loss of 0.27 dB, input and output return losses of 19 dB, isolation of 20 dB at fc, and phase and magnitude imbalance better than 2° and 0.2 dB across the Bandwidth (BW), respectively. The realized isolated balun has dimensions of 0.06λg × 0.03λg.

This work introduces a novel compact ultra-wideband (UWB) antenna designed for wearable applications, employing a bioinspired structure and machine learning (ML) techniques to achieve exceptional performance in the 3.10–10.42 GHz range. The antenna is fabricated by positioning conductive fabric on a polydimethylsiloxane polymer of 1 mm thickness to augment high flexibility and durability. Additionally, it pioneers integrating a complete ground plane to mitigate back radiation toward the human body, presenting a compact (35.5 × 30.5 × 1 mm3) UWB antenna design compliant with IEEE 802.15.6 standards. The design methodology includes using bandwidth enhancement techniques such as chamfering edges, slots, and adding stubs in the feed, along with applying ML to optimize the antenna’s dimensions for desired return loss characteristics. The proposed antenna demonstrates exceptional resilience to human body loading and physical deformation. The simulation and measurement results have good agreement. The K-nearest neighbour method beat the other ML algorithms maximum accuracy of 99.62% to predict the S11. According to the author’s best knowledge, this is the first compact UWB antenna with full ground specified by IEEE.802.15.6 with ML reported.

With the development of the communication field, more and more communication devices need multiple single-frequency antennas to work simultaneously. However, using multiple single-frequency antennas results in larger sizes. The miniaturized and dual-band communication system has become a new development trend. This paper designs a dual-band filtering patch antenna based on a multimode resonator, which is cascaded. The filter resonator part adopts step impedance resonance for branch shunt design, which can flexibly control the center frequency of two frequency bands. The filtering antenna utilizes a dual-layer substrate structure and achieves an integrated design through coupling probe feeding. This reduces the horizontal dimensions and improves miniaturization. Multiple radiation nulls are introduced outside the two-passband, and roll-off characteristics are evident. In addition, this design realizes high selectivity in the operating band. The antenna has large gains of 1.71 dBi and 6.25 dBi. It has good filtering and radiation characteristics.

This research proposes an inexpensive technique for wireless image transfer for security and surveillance applications. The technique uses a 5.8 GHz transmitter and receiver module, along with external antennas in the real-time image transfer within a radius of 100 m. The transferred images are stored in a laptop using a Python code-based graphical user interface application. Different antennas, dipole, circular split-ring resonators, hexagonal split-ring resonators, and metamaterial antennas are utilized for comparison. The Blind/Referenceless Image Spatial Quality Evaluator method is used to assess the picture quality of transferred images to quantify image transfer performance when no ground truth or reference photos are supplied. According to the presented results, images transferred using metamaterial antennas have higher quality than those transferred with other types of antennas. For security considerations, such a system can communicate and store the images in real time.

A 3D-printed polarization-independent low-cost lightweight and flexible frequency selective surface based dual-band microwave absorber is presented in this paper. Two concentric square loops fabricated at different heights using 3D printing technology are responsible for exhibiting dual-band responses at 3.32 GHz (S-band) and 5.46 GHz (C-band) with more than 97% absorptivities. The corresponding full widths at half maximum bandwidths are observed as 230 MHz (3.21–3.44 GHz) and 450 MHz (5.27–5.72 GHz). The proposed topology is polarization-insensitive owing to the four-fold symmetry. The absorption phenomenon is explained with the analysis of current distributions at the surface and impedance curves at the frequencies of resonance. Further, the performance has been evaluated for both planar and curved surfaces with different angles of curvature, and the good agreement between the measured and simulated responses confirms the flexible behavior of the proposed structure.

A novel metasurface offering polarization conversion characteristic in five bands is studied and developed in this paper. To provide the anisotropic feature to the structure, a diagonally placed tapered rod is combined with two semicircular stubs. Due to the controlling ability to convert horizontal to vertical polarization and vice versa, and linear to circular polarization (CP), it serves as a multifunctional polarization converter. Simulation results suggest that the proposed polarizer functions as cross polarizer over 4.74−5.12 and 9.12−13.48 GHz. Additionally, it exhibits a distinct type of rotational sense across 4.24−4.68, 5.24−8.64, and 13.72–15.14 GHz in its linear to CP conversion behavior. The axial ratio of the polarizer is well below 3 dB throughout overall CP bands due to the minimum tolerance level in reflection phases with respect to acceptable limits. Moreover, it is noticed that the sense of CP is left-handed in the first band while right-handed in the remaining two bands. Thus, the suggested polarizer has potential to be integrated with antennas for satellite, defense, industry applications for getting the desired type of polarization in the distinguished bands.

In this article, a low phase noise signal source to be used as local oscillator in pulse Doppler radio frequency (PDRF) sensor is proposed. Innovative design techniques for realization of the low phase noise frequency source using phase-locked loop (PLL) and dielectric resonator (DR) are presented. Qualitative investigations have been carried out on the effect of phase noise in PDRF sensor performance. An X-band vibration resistant PLL-based frequency source with phase noise better than −95 dBc at 1 kHz frequency offset has been designed here. It also presents the design of a 7.6 GHz low phase noise, vibration resistant DR oscillator. Systematic analysis of the key design aspects, their thermal-vibrational stability, and ease of integration with hybrid microwave integrated circuits have been disclosed. A prototype board is fabricated, assembled in a compact mechanical enclosure of dimension 55 × 55 × 15 mm3. Finally, developed module is experimentally validated under 7.6 g rms magnitude random vibration test in three axes and compared results with other state of-the-art similar works. The comparison clearly shows the merit of present research work over other similar existing works.

Liquid crystal microwave phased arrays (LC-MPAs) are regarded as an ideal approach to realize compact antennas owing to their advantages in cost, size, weight, and power consumption. However, the shortcoming in low radiation deflection efficiency has been one of LC-MPAs’ main application limitations. To optimize the steering performance of LC-MPAs, it is essential to model the channel imperfections and compensate for the phase errors. In this paper, a phase error estimation model is built by training a neural network to establish a nonlinear relationship between the near-field phase error and the far-field pattern, hence realizing fast calibration for LC-MPAs within several measured patterns. Simulations and experiments on a 64-channel, two-dimensional planar antenna were conducted to validate this method. The results show that this method offers precise phase error estimations of 3.58° on average, realizes a fast calibration process with several field-measured radiation patterns, and improves the performances of the LC-MPA by approximately 4%–10% in deflection efficiency at different steering angles.

This paper proposes an air-filled substrate integrated waveguide (AFSIW) bandpass filter with a miniaturized non-resonant node (NRN). The NRN structure is introduced between the three resonators, and its size is smaller than the resonator size, which can realize the NRN structure’s miniaturization and reduce the model’s size. The NRN size of this filter is 41% of the NRN size of the existing AFSIW filter. This filter also introduces a transmission zero (TZ) above the passband. The measured results show that the filter’s center frequency is 20.73 GHz, and the bandwidth is 0.86 GHz. The insertion loss in the passband is 0.95 dB, and the return loss is better than 23 dB. Due to the TZ in the upper stopband, the AFSIW filter obtained good selectivity.

This paper presents a design methodology for a broadband high-efficiency power amplifier (PA). The large available impedance space of the extended continuous Class-GF mode is employed. A novel output matching network of the PA consisting of a rectangular double transmission line structure is proposed to meet impedance requirements. To validate the effectiveness of this structure, a high-efficiency PA operating in 0.8–3.0 GHz is designed using a CGH40010F GaN transistor. The measured results demonstrate that the drain efficiency falls within the range of 63.2%–71.9%, the output power varies from 40.2 to 42.2 dBm, and the gain ranges from 9.4 to 11.3 dB within the frequency band of 0.8–3 GHz. The realized PA exhibits an extremely competitive relative bandwidth of 115.8%.

A multiresonance metasurface antenna is proposed which has wide bandwidth and low-profile. The characteristic mode theory is used to design antenna structure. Three ideal modes are obtained by adjusting the mode currents to optimize the radiation performance of the antenna. The characteristic mode analysis is used to model, analyze, and optimize the antenna, revealing the physical characteristics of the metasurface antenna. The slot is not only used as the feeding structure for exciting characteristic modes but also introduces a slot mode. Combining the slot mode with the metasurface modes, the bandwidth of the antenna is broadened. The antenna element has a relative bandwidth of 43.7%. To obtain higher gain, a 2 × 2 antenna array is proposed. The antenna array is simulated, fabricated, and measured. The results show that the relative bandwidth of the proposed metasurface antenna array is 31.6% with the gain of 12.3–15.8 dBi over the operating bandwidth.

This research article proposes a dual-sense dual-port wideband circularly polarized (CP) multi-input multi-output (MIMO) antenna designed for Wi-Fi 6E applications. The main novelty lies in achieving CP for both ports using a truncated rectangular-shaped aperture. By incorporating design and spatial diversity and defective ground structure between the two radiators, the design improves isolation and enables the antenna to generate Left-Hand Circular Polarization (LHCP)depending on the selected feed port. The proposed MIMO rectangular dielectric resonator antenna demonstrates an impressive impedance-matching bandwidth (IBW)from 5.5 to 8.0 GHz (37.10%) as well as an axial ratio bandwidth (ARBW) covering from 6.0 to 6.55 GHz (12.20%). Additionally, the dual-port wideband CP MIMO antenna exhibits satisfactory diversity performance parameters. To validate the simulated results, a physical prototype is fabricated and subjected to experimental testing. The measured outcomes of the fabricated model align closely with the simulated results, confirming the accuracy of the design. With both MIMO and CP capabilities and improved isolation, this proposed model proves beneficial in reducing latency and minimizing the impact of multipath fading. Therefore, it stands as an excellent choice for future devices utilizing the Wi-Fi 6E band due to its broad IBW and overlappingAR.

A systematic design approach is presented for the design of broadband high-efficiency power amplifiers (PAs) by combining an improved ring-resonant filter matching network with a series of continuous modes. The improved ring-resonant matching network presented can effectively enhance out-of-band attenuation and sharp roll-off characteristics by adding a compensation structure with parallel stub. To verify the proposed design theory, a 10-W GaN HEMT device is designed and fabricated. The test results indicate that from the operating frequency band of 0.55−3.3 GHz with a relative bandwidth of 142.9%, a saturated output power of 38.5−42 dBm, drain efficiency of 58.2−70.3%, and a gain of 8.5–12 dB can be achieved under 3 dB gain compression, indicating the rationality of the design theory.

Large reflector antennas, such as the European Space Agency deep space antennas (DSAs), practically always require struts to support the sub-reflector. While inevitable, they deteriorate the antenna performance. To minimize this deterioration, it is pivotal to understand the role played by different features, including struts diameter and shape. This paper proposes a detailed numerical investigation on the impact of these features on antenna efficiency and side lobes, for a test case comprising both DSA3 and DSA4. It is demonstrated, for the first time in a comprehensive and quantitative way that includes different permutations for the strut design, that both features are significant to define the deterioration, thus providing a significant feedback for struts design.

Path loss prediction (PLP) is an important feature of wireless communications because it allows a receiver to anticipate the signal strength that will be received from a transmitter at a given distance. The PLP is done by using machine learning models that take into account numerous aspects such as the frequency of the signal, the surroundings, and the type of antenna. Various machine learning methods are used to anticipate path loss propagation but it is difficult to predict path loss in unknown propagation conditions. In existing models rely on incomplete or outdated data, which can affect the accuracy and reliability of predictions and they do not take into account the effects of environmental factors, such as terrain, foliage, and weather conditions, on path loss. Furthermore, existing models are not robust enough to handle the real-world variability and uncertainty, leading to significant errors in predictions. To tackle this issue, a novel ultrahigh frequency (UHF) PLP based on K-nearest neighbors (KNNs) is developed for predicting and optimizing the path loss for UHF. In this proposed model, a KNN-based PLP has been used to predict the path loss in the UHF. This technique is used for high-accuracy PLP through KNN forecast route loss by determining the K-nearest data points to a particular test point based on a distance metric. Moreover, the existing models were not able to optimize path loss due to complex and large-scale machine learning models. Therefore, the stochastic gradient descent technique has been used to minimize the objective function, which is often a measure of the difference between the model’s predictions and the actual output that will fine-tune the parameters of the KNN model, by measuring the similarity between data points. This model is implemented using Python to make it a lot more convenient.

Resonant Bessel-beam launchers (BBLs)are radiating devices constituted by a cylindrical metallic cavity with a partially reflecting sheet (PRS) on top. Millimeter-wave resonant BBLs typically exhibit transverse magnetic (TM) polarization due to the use of coaxial probes as feeders and homogenized metasurfaces as PRS. Launchers showing either a purely transverse electric (TE) or a hybrid (quasi-TE) polarization have recently been proposed for realizing wireless power transfer (WPT) links in the radiative near-field region at millimeter waves. The former are obtained by means of a radial slot array as a feeder and a homogenized metasurface as a PRS. The latter are obtained by using a loop antenna as a feeder and an annular strip grating in the homogenization limit as radiating aperture. In this work, based on an original semi-analytical model, such a metasurface is demonstrated to show a dichroic behavior. This interpretation explains the improvement in terms of polarization purity with respect to more nondichroic conventional homogenized metasurfaces. The behavior of the annular strip grating under a pure TM polarization is tested with a coaxial feeder, whereas its behavior under a pure TE polarization is tested by means of the radial slot array feeder. Results confirm the validity of the proposed analysis, which is finally exploited to evaluate the WPT performance.

A bandwidth expansion strategy for ultra-wideband power amplifiers (PAs) is presented in this letter by adopting a parallel impedance matching architecture. This design strategy can effectively reduce the impedance conversion ratio between the load and the target impedance of the PA, thereby providing a feasible solution for broadband impedance matching. Subsequently, a commercially available 10 W gallium nitride device and a two-stage Wilkinson power divider network are combined to achieve the verification of the proposed theory. The results of the measurement show that within the target frequency band of 0.9–3.9 GHz, 58.5–71.2% of the drain efficiency and 9.1–12 dB of gain can be achieved with a saturated output power of 39.1–42 dBm.