As simulation has become an integral part of the overall life-cycle support of aircraft, the need for effective Virtual Engineering (VE) tools to support these activities has increased. FLIGHTLAB is a state-of-the-art, aircraft modelling and simulation software tool, that has been designed to address this need and is widely used in rotorcraft design, analysis, test and evaluation, and full-flight simulation applications. This VE tool supports the development and analysis of both fixed and rotary wing aircraft with an extensive library of modelling components which have been successfully used and validated in numerous, real-world applications. These components provide comprehensive modelling of aerodynamic, structural, control and propulsion disciplines. Analyses include performance, dynamic response, stability and control, airloads, and structural loads. Graphical User Interfaces and an interactive scripting language provide user-friendly operation. This paper describes the capabilities and validation activities that have been undertaken to support the development of the commercial VE toolset FLIGHTLAB over the last 20 years and discusses future rotorcraft challenges that could be addressed by enhancements to current generation VE tools.

Supersonic civil aircraft present a unique noise certification challenge. High specific thrust required for supersonic cruise results in high engine exhaust velocity and high levels of jet noise during take-off. Aerodynamics of thin, low-aspect-ratio wings equipped with relatively simple flap systems deepen the challenge. Advanced noise reduction procedures have been proposed for supersonic aircraft. These procedures promise to reduce certification noise levels, but they may require departures from normal reference procedures defined in noise regulations. The subject of this article is a take-off performance and noise assessment of a notional supersonic business jet. Analytical models of an airframe and a supersonic engine derived from a contemporary subsonic turbofan core are developed. These models are used to predict take-off trajectories and certification noise levels. Results indicate advanced take-off procedures are helpful in reducing noise along lateral sidelines.

It is a challenge for small, fixed-wing aerial vehicles to maintain flight stability under gusts. Inspired by the geometric features and the structural dynamic characteristics of the gliding bird wing, an elastic wing with similar characteristics was designed and optimised for use as part of unmanned aerial vehicle. A flight dynamic model, which includes the coupling of the longitudinal flight modes and the aeroelastic modes of the flexible wing, was built to analyse the mechanisms of specific coupling for the structural characteristics of the wing design, and how these specific couplings affect flight dynamics. The results showed that the bio-inspired elastic wing effectively allows alleviation of the gust response of the prototype through coupling effects of the short period and the first aeroelastic mode, even with a considerable frequency gap. These effects become more significant when the airspeed becomes larger. The conclusions of this research can facilitate further development of bird-sized unmanned aerial vehicles to extend their applications and make these vehicles more adaptive for flight in complex atmospheric environments.

In this paper, a new type of fixed-wing vertical take-off and landing, unmanned aerial vehicle (UAV) has been designed. Thrust-vector direct force control has been introduced in three axes to make UAV exhibit superior manoeuverability in transition flight. Considering the characteristics of UAV's dynamic model, which are non-linear, non-affine, and have redundant input, a two-stage progressive optimal control allocation method is developed, which can optimise position and attitude control in synthetical, and motivate effectors to generates desired force and moments. A task-oriented weight selection scheme is proposed to make objective function suitable for different tasks and flight conditions. In addition, a general constraint strategy is designed to guarantee the feasibility of optimal allocation results, which can largely reduce the onboard computation time. Simulations show that UAV can adjust flight attitude and use control effectors in an optimal way, and demonstrating satisfactory tracking of low-speed high-manoeuver flight paths.

The purpose of this paper is to outline the structure of the DLR integrated rotorcraft design process. The complexity of rotorcraft design requires the development of the tools directly by the specialists of the respective institutes, where the tools are continuously refined and published to authorised users. The integration of the tools into a suitable software framework by means of distributed computation and the harmonisation of the tools among each other are presented. This framework delivers a high level of modularity making the layout and testing of the process very flexible. This design environment covers the conceptual and preliminary design phases. Not only conventional main/tail rotor configurations can be designed, but also some other configurations with more than one main rotor. The fundamental concept behind the layout of the tools is demonstrated, especially the use of scaling and optimisation loops in connection with the different levels of fidelity and the different phases of design.

Non-axisymmetric endwalls in turbine stages have shown to be a robust method to improve the performance of turbines in both power generation and aero-derivative applications. Non-axisymmetric endwalls target the control of secondary flows and are designed using detailed computational fluid dynamics coupled with a variety of optimisation algorithms and utilising a number of objective functions according to the engine company or researcher's preference. These numerical predictions are often backed up by detailed measurements in linear and annular cascades and later proven in full-scale engine tests. Relatively little literature is available describing their performance in rotating test rigs or at conditions other than design, apart from that of the authors. This study comprehensively revisits the low-speed, model turbines used in the earlier study, replacing all of the 5-hole probe data with more accurate results and additional hot-film measurements. These results together with computational fluid dynamics solutions are used to show the success of the method across a large incidence range and to compare to earlier cascade results for a similar endwall and blade profile to establish the usefulness of cascade testing in this application. In addition, a comparison to two other off-design studies is made. Results indicate that the endwalls successfully improve the rotor total isentropic efficiency at all test conditions and that the improvement increases with increased turning in the blade row, from 0.5% to 1.8% across the incidence range. The results also compare well to the estimation of isentropic efficiency improvement that can be drawn from the cascade testing which stands at 1.55%.

Speculation on near-term scientific reasons for the exploration of lunar pits is offered alongside comments on possible longer-term human exploitation. It is proposed that in order to determine whether or not one or more of the pits offer access the large subsurface voids e.g. a non-collapsed lava tube, a preliminary reconnaissance mission solely focused on obtaining lateral images (and/or LiDAR maps) is needed. Possible concept options for such a preliminary reconnaissance mission are discussed. It is suggested that one of the best possible strategies is to employ a micro-sized probe (~0.3 m) that would hop from a nearby main landing spacecraft to the selected pit. After the surface position of the main lander is determined accurately, the probe would perform a ballistic hop, or hover-traverse, a distance of ~3 km over the lunar surface using existing propulsive and guidance technology capability. Once hovering above the pit, the probe or a separate tethered imaging unit would then be lowered into the pit to acquire the necessary subsurface void topology data. This data would then be transmitted back to Earth, directly, via the lander, or via a store-and-forward orbiting relay. Preliminary estimates indicate that a probe of ~14 kg (dry mass) is viable using a conventional hydrazine monopropellant system with a propellant mass fraction of less than ~0.2 (20%) including margins, suggesting a piggyback architecture would be feasible.