Efficient electron acceleration by a linearly chirped ultrashort laser pulse in vacuum is investigated using the particle swarm optimization method. By applying this method for optimizing the initial parameters of the laser pulse, a pronounced increase in final energy gain of the electron is obtained compared to that expected from the successive optimization method. Our results also suggest that the value of the optimal chirp parameter is independent of laser polarization and the energy gain could be insensitive to the sign of this parameter when the initial phase is optimally adjusted. In addition, utilizing the chirped laser pulse with optimized conditions for acceleration of an electron bunch reveals that the energy spectrum is shifted to considerably higher energies and the spatial distribution is significantly improved in a polarization-dependent manner.

We study the setting up of relativistic ponderomotive non-linearity in an under-dense collisionless cold plasma. Using the fluid model, coupled system of equations of the laser beam and electron plasma oscillations has been derived. We present the numerical simulation for this coupled system of equations, when the coupling arises through relativistic ponderomotive non-linearity. The filamentation of the laser beam has been found to vary appreciably with perturbation wave number. The results show that with time, localized structures become more complex and the plasma oscillation frequency spectra have several harmonic peaks at terahertz frequencies when the electron plasma frequency is in terahertz range and laser frequency is around 2.35 × 1015 rad/s. We also present the semi-analytical model to capture the underlying physics.

Thermal imaging diagnostics was used as a surface temperature mapping tool to characterize the energy density distribution of a high-intensity pulsed ion beam. This approach was tested on the TEMP-6 accelerator (200–250 kV, 150 ns). The beam composition included carbon ions (85%) and protons, and the energy density in the focus was 5–12 J/cm2. Targets of stainless steel, titanium, brass, copper, and tungsten were examined. Our observations show that the maximum energy density measured with the thermal imaging diagnostics considerably exceeds the ablation threshold of the targets. An analysis of the overheating mechanisms of each target was carried out, including metastable overheating of the target to above its boiling temperature during rapid heating; formation, migration, and the subsequent annealing of fast radiation-induced defects in the target under ion beam irradiation. This expands the range of energy density measurement for this thermal imaging diagnostics from 2–3 J/cm2 up to 10–12 J/cm2 but introduces error into the results of measurement. For a stainless steel target, this error exceeds 15% at an energy density of more than 4 J/cm2. A method of correcting the results of the thermal imaging diagnostics is developed for a pulsed ion beam under conditions of intense ablation of the target material.

The formation of a collisional shock wave by the light pressure of a short-laser pulse at intensities in the range of 1018–1023 W/cm2 is considered. In this regime the thermodynamic parameters of the equilibrium states, before and after the shock transition, are related to the relativistic Rankine–Hugoniot equations. The electron and ion temperatures associated with these shock waves are calculated. It is shown that if the time scale of energy dissipation is shorter than the laser pulse duration a collisional shock is formed. The electrons and the ions in the shock-heated layer may have equal or different temperatures, depending on the laser pulse duration, the material density and the laser intensity. This shock wave may serve as a heating mechanism in a fast ignition scheme.

We present a broad study of linear, clustered, noble gas puffs irradiated with the frequency doubled (527 nm) Titan laser at Lawrence Livermore National Laboratory. Pure Ar, Kr, and Xe clustered gas puffs, as well as two mixed-gas puffs consisting of KrAr and XeKrAr gases, make up the targets. Characterization experiments to determine gas-puff density show that varying the experimental parameter gas-delay timing (the delay between gas puff initialization and laser-gas-puff interaction) provides a simple control over the gas-puff density. X-ray emission (>1.4 keV) is studied as a function of gas composition, density, and delay timing. Xe gas puffs produce the strongest peak radiation in the several keV spectral region. The emitted radiation was found to be anisotropic, with smaller X-ray flux observed in the direction perpendicular to both laser beam propagation and polarization directions. The degree of anisotropy is independent of gas target type but increases with photon energy. X-ray spectroscopic measurements estimate plasma parameters and highlight their difference with previous studies. Electron beams with energy in excess of 72 keV are present in the noble gas-puff plasmas and results indicate that Ar plays a key role in their production. A drastic increase in harder X-ray emissions (X-ray flash effect) and multi-MeV electron-beam generation from Xe gas-puff plasma occurred when the laser beam was focused on the front edge of the linear gas puff.

The multi-petawatt (PW) lasers currently being built in Europe as part of the Extreme Light Infrastructure (ELI) project will be capable of generating femtosecond light pulses of ultra-relativistic intensities (~1023–1024 W/cm2) that have been unattainable so far. Such laser pulses can be used for the production of high-energy ion beams with unique features that could be applied in various fields of scientific and technological research. In this paper, the prospect of producing ultra-intense (intensity ≥1020 W/cm2) ultra-short (pico- or femtosecond) high-energy ion beams using multi-PW lasers is outlined. The results of numerical studies on the acceleration of light (carbon) ions, medium-heavy (copper) ions and super-heavy (lead) ions driven by a femtosecond laser pulse of ultra-relativistic intensity, performed with the use of a multi-dimensional (2D3 V) particle-in-cell code, are presented, and the ion acceleration mechanisms and properties of the generated ion beams are discussed. It is shown that both in the case of light ions and in the case of medium-heavy and super-heavy ions, ultra-intense femtosecond multi-GeV ion beams with a beam intensity much higher (by a factor ~102) and ion pulse durations much shorter (by a factor ~104–105) than achievable presently in conventional radio frequency-driven accelerators can be produced at laser intensities of 1023 W/cm2 predicted for the ELI lasers. Such ion beams can open the door to new areas of research in high-energy density physics, nuclear physics and inertial confinement fusion.

High inductive helical support provides a solution to controlling the alignment error of inner electrodes in magnetically insulated transmission lines (MITLs). Three-dimensional particle-in-cell simulations were performed to examine the current loss mechanism and the effects of structural parameters on electron flow in an MITL with a helical inductor. An empirical expression related to the ratio of electron current loss to anode current and the ratio of anode current to self-limited current was obtained. Electron current loss caused by helical inductor with different structures was displayed. The results indicate that the current loss in an MITL, near an inductive helical support, comprises both the inductor current and the electron current loss. The non-uniform structure and current of a helical inductor cause an abrupt change in the magnetic field near the helical support, which leads to anomalous behavior and current loss of electron flow. In addition, current loss in the inductive helical-supported MITL is negligible when the inductance of the support is sufficiently high. This work facilitates the estimation of electron current loss caused by the inductive helical support in MITLs.