Crossref Citations
This article has been cited by the following publications. This list is generated based on data provided by
Crossref.
Li, Frank Wei
Davis, Tyler
Jensen, C. G.
and
Red, W. E.
2004.
Rapid and Flexible Prototyping Through Direct Machining.
Computer-Aided Design and Applications,
Vol. 1,
Issue. 1-4,
p.
91.
Davis, Tyler A.
Carlson, Shane
Red, W. Ed
Jensen, C. Greg
and
Sipfle, Karl
2006.
Flexible in-process inspection through direct control.
Measurement,
Vol. 39,
Issue. 1,
p.
57.
Li, Wei
Red, Edward
Jensen, Greg
and
Evans, Mark
2007.
Reconfigurable Mechanisms for Application Control (RMAC): Applications.
Computer-Aided Design and Applications,
Vol. 4,
Issue. 1-4,
p.
549.
Huang, Hsu-Chih
and
Tsai, Ching-Chih
2008.
Adaptive Robust Control of an Omnidirectional Mobile Platform for Autonomous Service Robots in Polar Coordinates.
Journal of Intelligent and Robotic Systems,
Vol. 51,
Issue. 4,
p.
439.
Naseath, G. B.
and
Red, W. E.
2008.
Reducing Curvature by Deviating CAM Tool Paths within a Tolerance Band.
Computer-Aided Design and Applications,
Vol. 5,
Issue. 6,
p.
921.
Macek, Kristijan
Philippsen, Roland
and
Siegwart, Roland
2008.
Path following for autonomous vehicle navigation with inherent safety and dynamics margin.
p.
108.
Huang, Hsu-Chih
and
Tsai, Ching-Chih
2009.
Simultaneous tracking and stabilization of an omnidirectional mobile robot in polar coordinates: a unified control approach.
Robotica,
Vol. 27,
Issue. 3,
p.
447.
Natal, G Sartori
Chemori, A
Pierrot, F
and
Company, O
2010.
An experimental comparison of state observers for the control of a parallel manipulator without velocity measurements.
p.
2301.
Zhang, Qin
Wu, Zhibin
Kamiya, Yoshitsugu
and
Wang, Bo
2010.
Lift-down trajectory generation for multi-joint robot based on repeatedly direct kinematics algorithm.
p.
65.
Makhanov, Stanislav S.
2010.
Adaptable geometric patterns for five-axis machining: a survey.
The International Journal of Advanced Manufacturing Technology,
Vol. 47,
Issue. 9-12,
p.
1167.
Zhong, Guoliang
Kobayashi, Yukinori
Emaru, Takanori
and
Hoshino, Yohei
2012.
Intelligent Robotics and Applications.
Vol. 7507,
Issue. ,
p.
366.
Zhong, Guoliang
Kobayashi, Yukinori
Hoshino, Yohei
and
Emaru, Takanori
2013.
System modeling and tracking control of mobile manipulator subjected to dynamic interaction and uncertainty.
Nonlinear Dynamics,
Vol. 73,
Issue. 1-2,
p.
167.
Ajayi, Michael Oluwatosin
Djouani, Karim
and
Hamam, Yskandar
2015.
Bounded control of a full-exoskeleton device with four (4) Degree of Freedom.
p.
2425.
Boryga, Marek
Graboś, Andrzej
Kołodziej, Paweł
Gołacki, Krzysztof
and
Stropek, Zbigniew
2015.
Trajectory Planning with Obstacles on the Example of Tomato Harvest.
Agriculture and Agricultural Science Procedia,
Vol. 7,
Issue. ,
p.
27.
Olejnik, Peter R.
and
Ridgely, D. Brett
2020.
Command Shaping for a Torque, Jerk, and Acceleration Limited System.
Yang, Jixiang
Li, Dingwei
Ye, Congcong
and
Ding, Han
2020.
An analytical C3 continuous tool path corner smoothing algorithm for 6R robot manipulator.
Robotics and Computer-Integrated Manufacturing,
Vol. 64,
Issue. ,
p.
101947.
Byeon, Yong Jin
and
Kim, Byung Kook
2022.
Time-optimal cornering trajectory planning for car-like mobile robots containing actuator dynamics.
Robotica,
Vol. 40,
Issue. 5,
p.
1627.
Boryga, Marek
Kołodziej, Paweł
and
Gołacki, Krzysztof
2022.
The Use of Asymmetric Polynomial Profiles for Planning a Smooth Trajectory.
Applied Sciences,
Vol. 12,
Issue. 23,
p.
12284.
Sun, Hongwei
Yang, Jixiang
and
Ding, Han
2024.
A novel tool path smoothing algorithm of 6R manipulator considering pose-dependent dynamics by designing asymmetrical FIR filters.
Robotics and Computer-Integrated Manufacturing,
Vol. 86,
Issue. ,
p.
102681.