Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-24T06:20:03.975Z Has data issue: false hasContentIssue false
  • English
  • Français

Yield Point Phenomena During Indentation

Published online by Cambridge University Press:  10 February 2011

D. F. Bahr ,
C. M. Watkins ,
D. E. Kramer  and
W. W. Gerberich
D. F. Bahr
Affiliation:
Mechanical and Materials Engineering, Washington State University, Pullman, WA
C. M. Watkins
Affiliation:
Mechanical and Materials Engineering, Washington State University, Pullman, WA
D. E. Kramer
Affiliation:
Chemical Engineering and Materials Science, University of Minnesota, Minneapolis, MN
W. W. Gerberich
Affiliation:
Chemical Engineering and Materials Science, University of Minnesota, Minneapolis, MN
Get access

Abstract

The transition from purely elastic to plastic deformation during the initial stages of indentation is explored. The yield point is dependent on crystal orientation, and the extent of the transition from elastic to plastic deformation is compared to a model utilizing a superdislocation to accommodate deformation based on a change in shear stress before and after the yield point. The thickness of an oxide film is shown to impact, but not be solely responsible for, this phenomenon. High dislocation densities limit, and eventually eliminate, the ability to sustain elastic loading. Finally, the yield point is clearly both stress and time dependent; yielding occurs when a tip is held at a constant load over a period of time ranging from seconds to minutes.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 522: Symposium T – Fundamentals of Nanoindentation & Nanotribology , 1998 , 83
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Gane, N. and Bowden, F. P., J. Appl. Phys., 39, 1432 (1968).Google Scholar
2. Pethica, J. B. and Tabor, D., Surf. Sci., 89, 182 (1979).Google Scholar
3. Gerberich, W. W., Venkataraman, S. K., Huang, H., Harvey, S. E., and Kohlstedt, D. L., Acta Metall. Mater., 43, 1569 (1995).Google Scholar
4. Mann, A. B. and Pethica, J. B., Appl. Phys. Lett., 69, 907 (1996).Google Scholar
5. Asif, S. A. Syed and Pethica, J. B., Phil. Mag. A, 76, 1105 (1997).Google Scholar
6. Corcoran, S. G., Colton, R. J., Lilleodden, E. T., and Gerberich, W. W., Phys. Rev. B. 55, R16057 (1997)Google Scholar
7. Michalske, T. A. and Houston, J. E., Acta Mater., 46, 391 (1998).Google Scholar
8. Wu, T. W., J. Mater. Res., 6, 407 (1991).Google Scholar
9. Johnson, K. L., Contact Mechanics, Cambridge Press, Cambridge, 93–95, 153–184 (1985).Google Scholar
10. Bahr, D. F., Kramer, D. E., and Gerberich, W. W., Acta Mater., in press (1998).Google Scholar
11. Zielinski, W.,Huang, H. and Gerberich, W. W., Phil. Mag. A, 72,1221 (1995).Google Scholar
12. Bahr, D. F., Nelson, J. C., Tymiak, N. and Gerberich, W. W., J. Mater. Res., 12, 3345 (1997).Google Scholar
13. Kelchner, C. L. and Hamilton, J. C., presented at MRS Fall Meeting, Thin Films: Stresses and Mechanical Properties VII (1997).Google Scholar
14. Hirth, J. P. and Lothe, J., Theory of Dislocations, Mc Graw Hill, New York, p. 688 (1968).Google Scholar