Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-28T01:55:58.129Z Has data issue: false hasContentIssue false
  • English
  • Français

Temperature and Time-Dependent Ion Diffusion Across Stainless Steel-Zirconium Film Interface Studied by Scanning Surface Potential.

Published online by Cambridge University Press:  08 February 2012

M.E. Hawley ,
K.J. Hollis  and
P.O. Dickerson
M.E. Hawley
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545, U.S.A.
K.J. Hollis
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545, U.S.A.
P.O. Dickerson
Affiliation:
Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545, U.S.A.
Get access

Abstract

Zirconium is of interest in the development of high-density diffusion barriers in nuclear reactor applications because of its low thermal neutron absorption cross section and good thermal and mechanical properties. It is used in these applications to protect the low enriched fuel from interacting directly with the cladding material to prevent swelling and cracking of the fuel. In this work, we investigated the use of plasma spraying as a method to produce high quality, dense Zr barrier coatings over large surface areas. A thin sheet of 21Cr-6Ni-9Mn stainless steel (SS) was used as the substrate material. Both sides of the SS sheet were coated, one side at a time. A transfer arc (TA) current between a torch and the substrate was used to vary the substrate temperature to explore the effect of temperature and time on the film grain size, interface quality, and film porosity. The films were characterized using light optical microscopy (LOM), scanning probe microscopy (SPM) and Kelvin probe force microscopy (KPFM) and EDS-SEM Although the film quality did improved with temperature, at the elevated substrate temperatures used in this study, metal atoms from the substrate diffused into and, at the highest temperature and longest time, through the Zr coatings.

Keywords

barrier layerplasma depositionscanning probe microscopy (SPM)
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1383: Symposium A – Material Challenges in Current and Future Nuclear Technologies , 2012 , mrsf11-1383-a08-16
Copyright
Copyright © Materials Research Society 2012

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Herman, H., “Plasma Spray Deposition Processes,” MRS Bulletin 13(12), 60 (1988).Google Scholar
2. Sampath, S. and Herman, H., J. Therm. Spray Technol. 5(4), 445 (1996).Google Scholar
3. Hollis, K.J., Adv. Mat. & Processes 168(11), 57 (2010).Google Scholar
4. Hollis, K.J. and Pena, M.I., in Thermal Spray: Global Solutions for Future Application, edited by Marple, B.R. et al. . (DVS-ASM International, Singapore, 2010), pp. 439–444.Google Scholar
5. Nonnemacher, N., OBoyle, M.P., Wickramasinghe, H. K., Appl. Phys. Lett. 58(25), 2921 (1991).Google Scholar
6. Jacobs, H. Resolution and Contrast in Kelvin Probe Force Microscopy. J.Appl. Phys. 84, 1168 (1998).Google Scholar
7. Hawley, M.E., Hill, M.A., Wang, Y.Q., and Schulze, R.K., Mat. Res. Soc. Symp. Proceed. 986, p.149–155 (2007).Google Scholar
8. Perez, R.A., Nakajima, H., Dyment, F., Mat. Trans. 44(1), 2 (2003).Google Scholar