Hostname: page-component-78c5997874-94fs2 Total loading time: 0 Render date: 2024-11-03T04:12:38.305Z Has data issue: false hasContentIssue false
  • English
  • Français

The Stability of MoSi2 Films in Vacuum and Oxidizing Atmospheres

Published online by Cambridge University Press:  15 February 2011

L.E. Kolaya ,
D.J. Duquette  and
J.B. Hudson
L.E. Kolaya
Affiliation:
Currently at: Knolls Atomic Power Laboratory, P.O. Box 1072, Schenectady, NY 12301-1072
D.J. Duquette
Affiliation:
Materials Engineering Department, Rensselaer Polytechnic Institute, Troy, NY 12180
J.B. Hudson
Affiliation:
Materials Engineering Department, Rensselaer Polytechnic Institute, Troy, NY 12180
Get access

Abstract

The stability of MoSi2, films with respect to mass loss at high temperature has been investigated in vacuum and dry air environments at temperatures up to 1300° C. Samples were sputter deposited films of approximate composition MoSi3, on sapphire substrates. Post heat treatment analysis by X-ray diffraction, scanning electron microscopy, and electron microprobe analysis indicated that the films recrystallized, and that phase separation of the excess silicon from the MoSi2, occurred early in the heating process. With continued heating, silicon was lost from the films by evaporation, leading to the conversion of the films to Mo5Si3. The rate of mass loss was much less in the air environment due to the formation of a SiO2, layer which served as a diffusion barrier to silicon. Evidence of a reaction along the MoSi2,/A12O3 interface was observed visually, but could not be detected chemically.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 357: Symposium C – Structure and Properties of Interfaces in Ceramics , 1994 , 207
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Cook, J., Khan, A., Lee, E., and Mahapatra, R., Materials Science and Engineering, A155, 182 (1992).Google Scholar
2. Petrovic, J. J., MRS Bulletin, 18, 35 (1993).Google Scholar
3. Umakoshi, Y., Sakagami, T., Hirano, T., and Yamane, T., Acta Metallurgica Materialia, 38, 909 (1990).Google Scholar
4. Srinivasan, S. R. and Schwarz, R. B., J. of Materials Research, 7, 1610 (1992).Google Scholar
5. Yang, J. M. and Jeng, S. M., J. of Materials Research, 6, 505 (1991).Google Scholar
6. Xiao, L., Kim, Y. S., Abbaschian, R., and Hecht, R. J., Materials Science and Engineering, A144, 277 (1991).Google Scholar
7. Chow, T.P., Bower, D.H., VanArt, R.L., and Katz, W., J. Electrochemical Society, 130, 952 (1983).Google Scholar
8. Rastogi, R. S., Vankar, V. D. and Chopra, K. L., Thin Solid Films, 213, 45 (1992).Google Scholar
9. Murarka, S.P., Fraser, D.B., Retajczyk, T.F. Jr., and Sheng, T.T., J. Applied Physics, 51, 5380 (1980).Google Scholar
10. Maissel, L.I. and Glang, R., Handbook of Thin Film Technology, (McGraw-Hill Book Comp., NY, 1983).Google Scholar
11. Ohe, S., Computer Aided Data Book of Vapor Pressure, (Data Book Publishing Company, Tokyo, Japan, 1976).Google Scholar
12. Meschter, P. J., Scripta Metallurgica et Materialia, 25, 1065 (1991).Google Scholar
13. Xiao, L., Kim, Y. S., and Abbaschian, R. in Intermetallic Matrix Composites, ed. Anton, D.L., Martin, P. L., Miracle, D. B., and McMeeking, R., (Mater. Res. Soc. Proc., Pittsburgh, PA, 1991)pp. 399–404.Google Scholar