Hostname: page-component-78c5997874-g7gxr Total loading time: 0 Render date: 2024-11-02T20:36:41.815Z Has data issue: false hasContentIssue false
  • English
  • Français

Silicided Shallow Junction Formation Using Ion Implantation and Thermal Annealing

Published online by Cambridge University Press:  25 February 2011

Leonard M. Rubin ,
N. Herbots ,
D. Hoffman  and
D. Ma
Leonard M. Rubin
Affiliation:
Department of Materials Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139
N. Herbots
Affiliation:
Department of Materials Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139
D. Hoffman
Affiliation:
Standard Microsystems Corp., 35 Marcus Boulevard, Hauppauge, NY 11788
D. Ma
Affiliation:
Standard Microsystems Corp., 35 Marcus Boulevard, Hauppauge, NY 11788
Get access

Abstract

The combination of arsenic and boron implantation with rapid thermal annealing (RTA) has been investigated to form shallow p-n junctions under a titanium silicide (TiSi2) metallization. The use of TiSi2 as a connection material can lead to the destruction of the junction if the kinetics of silicidation and doping are not well controlled. The purpose of this study is to better understand and control these kinetics, using far-from equilibrium processing such as ion implantation and RTA. The structures were characterized by Rutherford Backscattering Spectometry (RBS) for arsenic and silicide profiling, Secondary Ion Mass Spectometry (SIMS) for boron profiling, Scanning Electron Microscopy (SEM), and electrical sheet resistance measurements. Two procedures were investigated. Both involved the thermal reaction of Ti thin films, sputter-deposited with thicknesses ranging between 40 and 80 nm. In the first experiment, the as-deposited films were implanted with either 115 keV arsenic or 28 keV boron to form the junction, disperse the native oxide, and ion beam mix the Ti and Si. The films were then subjected to an RTA at 750°C for 15 to 60 seconds, which leads to TiSi2 formation in unimplanted films. Implantation was found to actually prevent TiSi2 formation. Ion transport calculations indicated that dopant pile-up at the interface might inhibit silicidation while higher energies and larger implant doses can more effectively ion beam mix Ti and Si. A more attractive solution consists of first forming TiSi2 from the as-deposited Ti by RTA, and then implanting to form the junction. This resulted in better control of the junction thickness. A sharp increase in the TiSi2 resistivity was found after implantation but the original value could be restored by a second RTA. This RTA also electrically activated the dopants and recrystallized the junction. The material properties of Ti/Si and TiSi2/Si under ion bombardment, RTA, doping, and conventional furnace annealing will be discussed.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 128: Symposium A – Processing and Characterization of Materials Using Ion Beams , 1988 , 641
Copyright
Copyright © Materials Research Society 1989

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Murarka, S. P., Read, M. H., Doherty, C. J., and Fraser, D. B., J. Electrochem. Soc. 129 293 (1982).10.1149/1.2123815Google Scholar
[2] Murarka, S. P., J. Vac. Sci. Tech. 17 775 (1980).10.1116/1.570560Google Scholar
[3] Lau, C. K., See, Y. C., Scott, D. B., Bridges, J. M., Pema, S. M., and Davis, R. D., IEDM Tech. Dig., 714 (1982).Google Scholar
[4] Lanerolle, N. de, Hoffman, D., and Ma, D., J. Vac. Sci. Tech. (B) 5 1689 (1987).10.1116/1.583649Google Scholar
[5] Rubin, L., unpublished data.Google Scholar
[6] Biersak, J. P., Eckstein, W., Appl. Phys. A. 34 73 (1984).10.1007/BF00614759Google Scholar
[7] Park, H. K., Sachitano, J., McPherson, M., Yamaguchi, T., and Lehman, G., J. Vac. Sci. Tech. (A) 2 264 (1984).10.1116/1.572576CrossRefGoogle Scholar
[8] Pramanik, D., Deal, M., Saxena, A. N., and Wu, O. K., Advanced Applications of Ion Implantation, SPIE vol.530 159 (1985).10.1117/12.946482Google Scholar
[9] Ommen, A. H. van, Houtum, H. J. W. van, and Theunissen, A. M. L., J. Appl. Phys. 60 627 (1986).10.1063/1.337459Google Scholar
[10] Shukla, R. K. and Multani, J. S., IEEE V-MIC Conf. 470 (1987).Google Scholar
[11] Ting, C. Y., d'Heurle, F. M., Iyer, S. S., and Fryer, P. M., J. Electrochem. Soc. 133 2621 (1986).10.1149/1.2108491Google Scholar
[12] Gas, P., Deline, V., d'Heurle, F. M., and Scilla, G., J. Appl. Phys. 60 1634 (1986).10.1063/1.337252Google Scholar
[13] Ku, Y. H., Louis, E., Lee, S. K., Shih, D. K., Kwong, D. L., Lee, C. O., and Yeargain, J. R., Advanced Processing of Semiconductor Devices, SPIE vol.797. 61 (1987).10.1117/12.941026Google Scholar