Hostname: page-component-586b7cd67f-t8hqh Total loading time: 0 Render date: 2024-11-28T22:37:13.799Z Has data issue: false hasContentIssue false
  • English
  • Français

PZT and Electrode Enhancements of Mems Based Micro Heat Engine for Power Generation

Published online by Cambridge University Press:  01 February 2011

A.L. Olson ,
L.M. Eakins ,
B.W. Olson ,
D.F. Bahr ,
C.D. Richards  and
R.F. Richards
A.L. Olson
Affiliation:
Mechanical and Materials Engineering, Washington State University, Pullman, WA
L.M. Eakins
Affiliation:
Mechanical and Materials Engineering, Washington State University, Pullman, WA
B.W. Olson
Affiliation:
Mechanical and Materials Engineering, Washington State University, Pullman, WA
D.F. Bahr
Affiliation:
Mechanical and Materials Engineering, Washington State University, Pullman, WA
C.D. Richards
Affiliation:
Mechanical and Materials Engineering, Washington State University, Pullman, WA
R.F. Richards
Affiliation:
Mechanical and Materials Engineering, Washington State University, Pullman, WA
Get access

Abstract

The P3 Micro Heat Engine relies on a thin film PZT based transducer to convert mechanical energy into usable electrical power. In an effort to increase process yield for these were used on sputtered Ti/Pt bottom electrodes to compare roughness, grain size, and diffusion for annealing temperatures between 550 and 700 °C. For an optimized bottom electrode, process yield for various sized top electrodes were then studied for PZT thickness between 0.54 and 1.62 for reducing stress concentrations. Two PZT etching geometries on 2.3 μm thick Si/SiO2 membranes, with 1.5-3.5 mm side-lengths, were examined and one was used to increase the strain at failure by at least 40%. Integrating improvements in process yield and strain at failure, single PZT based MEMS devices capable of generating power of up to 1 mW and in excess of 2 volts have been demonstrated operating at frequencies between 300 and 1,100 Hz.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 730: Symposium V – Materials for Energy Storage, Generation, and Transport , 2002 , V5.19
Copyright
Copyright © Materials Research Society 2002

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Xu, C., Hall, J., Richards, C., Bahr, D., and Richards, R., ASME IMECE MEMS Symposium MEMS 2, 261 (2000).Google Scholar
2. Chen, San-Yuan, Chen, I-Wei, J. Am. Ceram. Soc., 77, 2332 (1994).Google Scholar
3. Al-Shareef, H.N., Dimos, D., Tuttle, B.A., Raymond, M.V., J. Mater. Res. 12, 347 (1997).Google Scholar
4. Vélu, G., Rèmiens, D., Journal of the European Ceramic Society 19, 2005 (1999).Google Scholar
5. Klissurska, Radosveta D., Maeder, Thomas, Brooks, Keith G., Setter, Nava, Microelectronic Engineering 29, 297 (1995).Google Scholar
6. Timoshenko, S., Woinowski-Krieger, S., Theory of Plates and Shells, McGraw-Hill, New York (1982).Google Scholar
7. Vlassak, J.J., Nix, W.D., J. Mater. Res. 7, 3242 (1992).Google Scholar
8. Hohlfelder, Robert J., Ph.D. Thesis, Stanford Unversity (1999).Google Scholar
9. Bahr, D.F., Bruce, K.R., Olson, B.W., Eakins, L.M., Richards, C.D., and Richards, R.F., Proceedings of the Materials Research Society 687, 4.3 (2002).Google Scholar
10. Hall, J.D., Apperson, N.E., Crozier, B.T., Xu, C., Richards, R.F., Bahr, D.F., and Richards, C.D., Review of Scientific Instrumentation 73, 2067 (2002).Google Scholar