Hostname: page-component-78c5997874-t5tsf Total loading time: 0 Render date: 2024-11-08T02:31:11.189Z Has data issue: false hasContentIssue false
  • English
  • Français

Properties of Films Prepared from Low Surface Area/Density Alumina-Silica

Published online by Cambridge University Press:  28 February 2011

S.L. Hietala ,
D.M. Smith ,
V.M. Hietala ,
G.C. Frye ,
A.J. Hurd  and
C.J. Brinker
S.L. Hietala
Affiliation:
Unm/Nsf Center For Micro-Engineered Ceramics, University of New Mexico;
D.M. Smith
Affiliation:
Unm/Nsf Center For Micro-Engineered Ceramics, University of New Mexico;
V.M. Hietala
Affiliation:
Sandia National Laboratories, Albuquerque, NM
G.C. Frye
Affiliation:
Sandia National Laboratories, Albuquerque, NM
A.J. Hurd
Affiliation:
Sandia National Laboratories, Albuquerque, NM
C.J. Brinker
Affiliation:
Sandia National Laboratories, Albuquerque, NM
Get access

Abstract

A sol-gel method was used to prepare bulk, closed pore, amorphous alumina-silica. Films prepared from this 47wt% A12O3-SiO2 composition were examined by SAW, ellipsometry and electrical measurements. The films were found to have a surface area of 1.1 cm2/cm2, a refractive index of 1.44 at 633 nm, and a relative permittivity of 6.2 at 200 KHz. These properties indicate potential applications as hermetic seals, barrier coatings, dielectric layers for capacitors and passivation coatings for electronic circuits.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 180: Symposium A – Better Ceramics Through Chemistry IV , 1990 , 433
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Hietala, S.L., Smith, D.M., Golden, J.L. and Brinker, C.J., J. Amer. Cer. Soc. 721, 2354 (1989).Google Scholar
2. Hietala, S.L., Smith, D.M., Brinker, C.J., Hurd, A.J., Dando, N. and Carim, A.H.. J. Amer. Cer. Soc. in press (1990).Google Scholar
3. Glaves, C.L., Frye, G.C., Smith, D.M., Brinker, C.J., Datye, A., Ricco, A.J. and Martin, S.J., Langmuir 5. 459 (1989).Google Scholar
4. Pouxviel, J.C. and Boilot, J.P. in Ultrstrueture Proceesing of Advanced Ceramics, edited by Mackenzie, J.D. and Ulrich, D.R. (1988) pp. 197–209.Google Scholar
5. Kingery, W.D., Bowman, H.K. and Uhlmann, D.R., Introduction to Ceramic, 2nd ed. (John Wiley & Sons, 1976) chapter 18.Google Scholar
6. Weast, R.C., ed., CRC Handhook of Chemistry and Physics, 63rd ed. (CRC press, 1982–1983) p. B-143 Google Scholar
7. Wefers, K. and Bell, G.N., Technical Paper #19. Alcoa Research Laboratories, 1972.Google Scholar