Hostname: page-component-78c5997874-fbnjt Total loading time: 0 Render date: 2024-11-02T19:00:47.835Z Has data issue: false hasContentIssue false

Microstructures in Cold-Rolled Ni3Al Single Crystals

Published online by Cambridge University Press:  26 February 2011

Kyosuke Kishida
Affiliation:
Materials Engineering Laboratory, National Institute for Materials Science, 1–2–1 Sengen, Tsukuba, Ibaraki 305–0047, JAPAN
Masahiko Demura
Affiliation:
Materials Engineering Laboratory, National Institute for Materials Science, 1–2–1 Sengen, Tsukuba, Ibaraki 305–0047, JAPAN
Toshiyuki Hirano
Affiliation:
Materials Engineering Laboratory, National Institute for Materials Science, 1–2–1 Sengen, Tsukuba, Ibaraki 305–0047, JAPAN
Get access

Abstract

Microstructure evolution during cold rolling of binary stoichiometric Ni3Al single crystals was examined by the optical (OM) and transmission electron microscopy (TEM). In the case of the <001> initial RD, the banded structure is formed. Inside each matrix band, the localized shear deformations occur alternately on two {111} planes. In addition, huge amounts of widely extended superlattice intrinsic stacking faults (SISFs) are observed from relatively early stage of cold rolling. The occurrence of the localized shear deformation is considered to be controlled by the SISFs since they must be strong obstacles for the dislocation motion on the other glide plane. The extensive formation of the SISFs is therefore considered to be one of the most important microstructural features which control the cold rolling behavior of Ni3Al.

Type
Research Article
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Sun, Y.Q. and Hazzledine, P.M., “Geometry of dissociation glide in L12 γ’- phase”, Dislocations in Solids Vol. 10: L12 Ordered Alloys, ed. Nabarro, F.R.N. and Duesbery, M.S. (Elsevier, Amsterdam, 1996), chapter 49, pp. 2768.Google Scholar
2. Veyssiere, P. and Saada, G., “Microscopy and plasticity of the L12 γ’ phase”, Dislocations in Solids Vol. 10: L12 Ordered Alloys, ed. Nabarro, F.R.N. and Duesbery, M.S. (Elsevier, Amsterdam, 1996), chapter 53, pp. 253441.Google Scholar
3. Ball, J. and Gottstein, G., Intermetallics, 1, 171 (1993).Google Scholar
4. Chowdhury, S.G., Ray, R.K., Jena, A.K., Mater. Sci. Engng. A, 246, 289 (1998).Google Scholar
5. Kishida, K., Demura, M., Suga, Y. and Hirano, T., Philos. Mag., 83, 3029 (2003).Google Scholar
6. Demura, M., Kishida, K., Suga, Y., Takanashi, M., and Hirano, T., Scripta Mater., 47, 267 (2002)Google Scholar
7. Demura, M., Suga, Y., Umezawa, O., Kishida, K., George, E. P., and Hirano, T., Intermetallics, 9, 157 (2001).Google Scholar
8. Kishida, K., Demura, M. and Hirano, T., unpublished work.Google Scholar
9. Nabarro, F.R.N., Basinski, Z.S. and Holt, D.B., Advances in Physics, 13, 193 (1964).Google Scholar