Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-28T20:04:55.539Z Has data issue: false hasContentIssue false
  • English
  • Français

Functional Passive Sensor System Using Reflective SAW Delay Line

Published online by Cambridge University Press:  01 February 2011

Tooru Nomura ,
Tomoe Kosaka  and
Atushi Saitoh
Tooru Nomura
Affiliation:
[email protected], Shibaura Institute of Technology, Faculty of Engineering, 3-9-14 Shibaura, Minato-ku, Tokyo, N/A, 108-8548, Japan, +81-3-5476-2480, +81-3-5476-3164
Tomoe Kosaka
Affiliation:
[email protected], Shibaura Institute of Technology, Faculty of Engineering, Japan
Atushi Saitoh
Affiliation:
[email protected], Shibaura Institute of Technology, Faculty of Engineering, Japan
Get access

Abstract

A new passive and remote SAW sensor system having ID tag function is presented. Surface acoustic wave (SAW) devices have been widely used as a chemical and physical sensor for measuring the environment. SAW devices have been also used as identification tags (ID tags). The majority of the work reported on SAW sensors to date has used Rayleigh mode SAW and are concerning a delay line. The other hand, it has been shown that the sensors utilizing the shear horizontal mode SAW (SH-SAW) can be designed to sense the liquid properties. The SH-SAW has the unique characteristic of complete reflection at a 90 degree edge normal to the direction of the propagation. This characteristic makes it possible to construct a reflective delay line using the edge reflection. The reflective delay line can be used for as passive and remote sensing.

In this paper, a passive and remote SAW sensor with a function of identification tags has been designed by using the reflective SH-SAW delay line. The reflective delay line was constructed on the 36 YX LiTaO3 substrate having a 90 degree edge normal to the direction of the SAW propagation. Passive and remote SAW sensor consists of several reflective delay lines having different propagation length. The passive sensor and ID tags were made by the multi-channel delay line. The responses of the sensor and ID tags using the edge reflection of SH-SAW are obtained in time domain. Several experiments were performed to verify the performances of the multi-channel edge reflection sensor. The basic characteristics of the reflective SAW sensor were obtained by measuring the amplitude and phase of reflected wave. The obtained results showed that the reflective SH-SAW sensor was very effective for sensing the physical and chemical properties.

Wireless systems are also suggested for the effective operation of the passive SAW sensor. A novel and simple electronic circuit system for accurately measuring the phase characteristics of responses form multi-channel is proposed. In the application, the reflective delay line has been mounted on cantilever to monitor the strain experimentally. The variation of the SH-SAW velocity on the delay line caused by a strain was measured as the passive SAW sensor response. The velocity varied in proportion to the strain applied to the propagation surface. The results showed that the passive sensor was very effective to measure the strain in a wireless mode and it was found that the system is very suitable to health and safety monitoring of building or airplane wing.

Finally it will be shown some applications of the wireless sensor with ID tags on the measurement of the conductivity and viscosity of same liquids.

Keywords

sensoracousticdevices
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 888: Symposium V – Materials and Devices for Smart Systems II , 2005 , 0888-V10-01
Copyright
Copyright © Materials Research Society 2006

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Wohltjen, H. and Dessy, R., Analytical Chem., 51, no.9, pp.1485–0000 (1979).Google Scholar
2. Motamedi, M.E. and White, R.M., IEEE Trans. Ultrason. Ferroelec. Freq. Contr., UFFC–34, no.2, p.122 (1987).Google Scholar
3. Wohltjen, H. in Surface acoustic wave microsensor, Proc. of 4th International Conference on Solid sensors and actuators, Tokyo, p.471 (1987).Google Scholar
4. Grate, J.W., Martin, S.J., and White, R.M., Analytical Chem., 65, pp.940A–948A (1993).Google Scholar
5. Grate, J.W., Martin, S.J., and White, R.M., Analytical Chem., 65, pp.987A–996A (1993).Google Scholar
6. Pohl, A., IEEE Trans. Ultrson. Ferroelec. Freq. Conr., 47, no.2, pp.317–332, March, 2000.Google Scholar
7. Reindl, L., Scholl, G., Ostertag, T., Scherr, H., Wolff, U. and Schmidt, F., IEEE Trans. Ferroelec. Freq. Contr., 45, no.5, pp.1281–1292(1998).Google Scholar
8. Nakamura, K., Kazumi, M. and Shimizu, H. in SH-type and Rayleigh-type surface waves on rotated Y-cut LiTaO3, Proc. 1977 IEEE Ultrasonics Symposium, pp.37–40(1977).Google Scholar
9. Kadota, M., Ago, J., Horiuchi, H. and Morii, H., Jpn. J. Appl. Phys., 39, pp.3045–3048 (2000).Google Scholar
10. Nomura, T., Saitoh, A. and Tokuyama, H. in Wireless sensor system using surface acoustic wave device, Proceedings of the 20th Sensor Symposium, pp.191–194 (2003).Google Scholar
11. Nomura, T., Saitoh, A. and Miyazaki, T. in Gas sensor using complete reflection at free edge of SH-SAW, Ferroelectrics, 273, pp.113–118 (2002).Google Scholar
12. Nomura, T. and Saitoh, A. in Liquid sensor system using reflecting surface acoustic wave delay lines, Proc. of IEEE Sensors 2002, pp.507–510(2002).Google Scholar